This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$71.08
In Stock
Order within the next 3 hrs and your part ships today!
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.73
In Stock
Order within the next 3 hrs and your part ships today!
This white dryer lint filter screen collects lint as it passes through the dryer vent.
$36.35
In Stock
Order within the next 3 hrs and your part ships today!
Questions And Answers for FSE446RHS2
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wayne
July 25, 2021
Dryer comes on, starts heating and spinning then shuts off after a few seconds.
For model number FSE446RHS2
Hello Wayne, Thank you for the question. The appliance could be over heating. We suggest testing the Thermal Limiter and the High Limit Thermostat. You can test the parts with a multi meter to check for continuity. We hope this helps!
Hello Larry, thank you for your question. We have a link to the manual in hopes that the information you are seeking may be in there. If not, this may be a question of the manufacturer. https://partselectcom.azureedge.net/assets/manuals/09EDFFC7C67CA55E29BA1A2E43E864785F3008F1.pdf. We hope this helps.
Was this helpful?
Thank you for voting!
Kim
March 13, 2020
Stacked washer/dryer. Dryer functions. Washer will drain, but won't spin.
For model number FSE446RHS2
Hello, Thank you for your question. If your washer fills with water but doesn't agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. You will want to check the washing machine's spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn't work, the belt may be loose or broken. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.