This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. This part is located in the blower housing.
$63.58
In Stock
Questions And Answers for FFLE4033QT0
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Thom
January 4, 2020
The washer will run but won't spin
For model number FFLE4033QT0
Hello Thom, thank you for your question. The first part we would recommend testing to correct this issue is the lid lock PartSelect Number: PS11703541. If this part does not activate, the unit will not go into the spin mode. If that part is fine, the next parts we would recommend testing/replacing are the sensor PartSelect Number: PS11770422 and actuator PartSelect Number: PS8746947. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Andrea
January 17, 2020
The washing machine is leaking a small amount of water during the wash cycle?
For model number FFLE4033QT0
Good Day Andrea. Thank you for your question in regards to your unit (Model Number FFLE4033QT0). Based on our research we have found the following potential issues that you may be having along with their solutions: 1) Loose fill hose connection at faucet or washer (Solution - Check and tighten hose connections. Install rubber sealing washers provided). 2) House drain pipes are clogged (Solution - Unclog drain pipes. Contact plumber if necessary). We hope this helps. Best Regards.
Was this helpful?
Thank you for voting!
Patrick
September 22, 2023
Power was restored after power outage and the Dryer works well but, only the pump and lid latch work on the Washer..
Washer does not operate.. Plz advise..
For model number FFLE4033QT0
Hi Patrick, thank you for reaching out. We would recommend checking the electronic control board, part number PS12364902, it manages the washer's functions such as filling, washing, draining and spinning. Good luck with your repair!
does not drain water, It's full of water and I don't know what to do.
For model number FFLE4033QT0
Hello Karmen, thank you for contacting us. You may need to disconnect the hose from the drain pump to take the water out from the washer tub. We would recommend checking the drain hose for cleaning. If the issue arises again, then you may need to replace the drain pump, part number PS16218540, to solve the problem. Glad to be of help!
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.