The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
$45.60
In Stock
Order within the next 8 hrs and your part ships today!
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
$47.19
In Stock
Order within the next 8 hrs and your part ships today!
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
$8.76
In Stock
Order within the next 8 hrs and your part ships today!
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
$41.19
In Stock
Order within the next 8 hrs and your part ships today!
Order within the next 8 hrs and your part ships today!
Questions And Answers for FFCD2413UB3A
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
September 23, 2023
Cannot change run mode. Ie stays on heavy wash all the time and heated dry. Does it need a a new contact strip? Machine is two years old.
For model number FFCD2413UB3A
Hello Mike, thank you for contacting us. According to our research, if the unit is stuck on heavy wash or heated dry, then there is an issue with the user interface control board, part number PS12585627. However, before replacing it, unplug the dishwasher or flip the circuit breaker off to the dishwasher and use a hair dryer to heat up the user interface control board. Rub your thumb over the heated dry button and wait 5 minutes for it to cool. Now plug the dishwasher back in and see if the issue clears up. If not, then the entire user interface control board would have to be replaced to resolve the issue. Glad to be of assistance!
Frigidaire dishwasher fills with water but then does not start the wash cycle. It fills and then stops. When I hold in the start button for 3 seconds to cancel, dishwasher drains normally. What could cause this?
For model number FFCD2413UB3A
Hi Chad, thank you for reaching out. Based on the description that you have provided, we would recommend checking the following parts: motor and pump assembly, part number PS12712308, and lower spray arm, part number PS12585623. If checking these does not fix the issue, then you may need to replace the electronic control board, part number PS12585627. We hope this sorts out your problem!
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.