This 3-coil 5500 watts heating element with housing is used to produce heat to dry the clothes in your dryer. The heating element is strung with a coiled wired. The wire receives, but resists a contro...
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. This part is located in the blower housing.
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
INCLUDES 5304523151 SHAFT, 5304523152 ROLLER, 5304523153 NUT, 5304523154 SPACER.
$93.76
In Stock
Questions And Answers for FASE7021NW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michelle
October 11, 2023
Control knob will only work when you have it set to heavy duty, while putting slight pressure to set for time to read 1:05 minutes. If pressure is not on knob only 15 minute cycle shows. Temp button is set at high, will not change, Dry level will only set at high. Unable to select any other option. After drying cycle completed it reads error code E64. End of cycle chimes for 5-10 minutes after pushing cancel button numerous times. Is this fixable? Thank you.
For model number FASE7021NW0
Hello Michelle, thank you for getting in touch. According to our research, error code E64 indicates that the heating element in your dryer is not functioning properly. We recommend checking the heating element. If the problem still continues, we suggest replacing the control board, part number PS10057458, to fix the issue. It manages the functions of the dryer such as drying time and temperature. We hope that helps!
Good Day Julian. Thank you for your question in regards to your unit (Model Number FASE7021NW0). Based on our research, "LOC" is an indication that the Child Lock on your unit has been engaged. We have found the following information that should assist you in disengaged this function: Press and hold the Options and Select buttons for 10 seconds or until the “LOC” on the display is cleared. We hope this helps! Best Regards.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)
