This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. This part is located in the blower housing.
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
INCLUDES 5304523151 SHAFT, 5304523152 ROLLER, 5304523153 NUT, 5304523154 SPACER.
$93.76
In Stock
Questions And Answers for FAQE7001LW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Donald
December 9, 2019
Dryer finishes drying cycle but does not shut off. Control panel is blank because cycle has completed. Open door, shut door, dryer runs without setting dryer.
For model number FAQE7001LW0
Hello Donald, Thank you for the question. This is normally an indication the cycle timer is defective. The timer for this model is built into the Control Board, PartSelect Number PS12724038. Hope this helps!
Our dryer requires several starts before it finally runs. Lights flash, sometimes beeps for no reason & will not shut off completely at end of cycle. Control board?
For model number FAQE7001LW0
Hello Lee, thank you for your question. Yes, we would suggest the control board also. The part number is PS12724038. We hope to hear from you soon.
My dryer makes thump and spin sound. Will replacing belt fix problems
For model number FAQE7001LW0
Hi Karen, thank you for reaching out. Yes, based on our research, the most likely cause of this issue is a worn-out or damaged belt, part number PS2349294, which may need to be replaced. Please submit a new question if you have any follow-ups!
Hi Knial, thank you for contacting us. Based on our understanding of the issue, we would recommend checking the belt, part number PS2349294, as it is most likely faulty and may need to be replaced. We hope this sorts out your problem!
Hi Carlos, thank you for your inquiry. Based on the description that you have provided, we would recommend replacing the control board, part number PS12724038, to fix the issue. We hope that helps!
When I described the noise to a YouTube appliance diagnostician, I was directed to check the felt seals front and back of the rotating drum for wear, tears, or foreign objects. As it happens the felt seals looked find and there were foreign objects so, not wanting to disassemble and reassemble the dryer more than I had, I ended up replacing all the replaceable moving parts that I considered possible culprits: The idler tension spring, the idler tension bracket (which includes a nylon pulley wheel), the drum belt, the five rubber-tipped bearings that support the drum and keep it in place, and the foam seal on the blower housing which seemed a little brittle and old, as well as high-temperature adhesive for the latter. The instructional videos here and on YouTube were extremely helpful (I doubt that I would have attempted this job at all, had I not watched these ahead of time). The most time-consuming aspect was waiting for the arrival of the parts as I didn't order them all at the same time or all from the same place (I ordered from whomever could ship me a given part the fastest. Disassembly took less than an hour. Re-assembly with the new parts in place took about the same but was a little more awkward because this appliance sits in a very narrow closet and it's difficult to ensure that the 4" flexible duct stays in place when sliding the appliance back into the closet. No regrets. Now I know the basics if this dryer needs attention in future and I also know all the parts that I can eliminate as suspects in any future maintenance (the parts that I replaced)