The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, me...
$69.21
In Stock
Order within the next 5 hrs and your part ships today!
The drum roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter...
$163.39
In Stock
Order within the next 5 hrs and your part ships today!
This is an authentic dryer lint filter cover sourced directly from the manufacturer. It protects the more delicate lint filter in your dryer, so that it doesn’t get damaged and lint can’t mix in with ...
$74.40
In Stock
Order within the next 5 hrs and your part ships today!
This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are not...
$54.63
In Stock
Order within the next 5 hrs and your part ships today!
Order within the next 5 hrs and your part ships today!
Questions And Answers for DLEX3370W
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry
August 12, 2021
Hit start and you get two clicks and nothing else. I have no idea what to could be?
For model number DLEX3370W
Hello Jerry, Thank you for the question. We suggest testing the Door Switch, PartSelect Number PS3529308. If this doesn't activate the unit will not start its cycles. We hope this helps!
Hello Sid, thank you for writing. Here is a link to the page on what parts to check when this issue occurs and how to check them: https://www.partselect.com/Repair/Dryer/Will-Not-Start/ . Good luck with your repair!
Was this helpful?
Thank you for voting!
Ray
January 26, 2023
Do you have any leveling legs that work with this model LG dryer-dlex3370w?
For model number DLEX3370W
Hi Ray,
Thank you for your question. The part number listed under your model number for the leg is PS3523560. If you would like to place an order for it, please call our customer service line and anyone will be happy to assist you. We look forward to hearing from you!
The rubber gasket on my dryer door is falling off, is it possible to buy a replacement gasket and, if so, how do I attach it? Any information you can provide would be greatly appreciated. Thank you!
For model number DLEX3370W
Hi Nora, thank you for reaching out. The door gasket, part number PS3535212, is compatible with the given model. Firstly, take a screwdriver to unthread the screws of the door hinges securing the door. Detach the door, now remove all the screws from the inner panel. Separate the inner panel, pull off the gasket, and install a new one by aligning the lip of the gasket on the inner panel. When the gasket is properly joined to the inner or outer panel, thread all the screws again with the same orientation and attached the door to the door hinges. We hope this information helps!
I have a problem with my dryer, the drum runs when it is plugged in. Just started
For model number DLEX3370W
Hi Duane, thank you for the question. Based on our understanding of the issue, we would suggest you check the display control board, part number PS11710911, as it is most likely faulty and may need to be replaced. We hope this information is useful!
Had to replace front drum support rollers. Removed screws underneath top in back that held bracket that keeps top in place. Slid top towards rear and lifted up. Removed 4 screws that hold plastic front panel in place (inside..2 on each corner) Unplugged front panel electric plugs to remove panel. Opened door..removed 2 screws at bottom of door opening. Removed screws on top of front panel. Unplugged door switch plug. Removed front panel. Removed right front roller with 9/16th wrench for nut. Adjustable for back of stud. Lifted up on drum to get roller out. Reversed to install. Left roller a bit harder to get to stud. Removed and installed same as right side. Did not attempt to replace rear rollers. Have them if needed but very much more involved to replace.
I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.
Removed existing parts using screwdriver, positioned new parts in dryer and re-inserted screws, tightened - done. Piece of cake, even for someone who cannot saw a straight line with a chop saw.
