This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
This dryer lint screen is for laundry centers.
Dryer lint screen captures lint and debris from the exhaust air flowing from the dryer.
Follow the instructions in the owner's manual when installing this part.
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
$119.16
In Stock
Questions And Answers for CFLE1011MW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
February 8, 2023
What is the Cu size for the Washer and Dryer?
For model number CFLE1011MW0
Hello James, Thank you for your inquiry. Researching the model number that you have provided, we show that the washer has a 3.4 cubic foot capacity, and the dryer has a 5.5 cubic foot capacity. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joe
April 5, 2023
Why do I have to reset the breaker in the wall panel to get the washer to work?
For model number CFLE1011MW0
Hi Joe, thank you for reaching out. We believe the most likely reasons for this problem are an overloaded circuit, overheated appliance, electrical short, or ground fault issue. You may need to check the motor, part number PS5574018, to ensure it is not overloading. Before replacing it, we suggest checking the wire connections to make sure they are connected properly. We hope this solves your problem!
serial number is 4E34915731, my model number reads FFLE1011MW (no 0)
This is a Washer/Dryer combo. The washer does not drain, which says I need a pump. But also the dryer does not heat up. I don't see any symptom checkers for the dryer not heating. Can you assist?
For model number CFLE1011MW0
Hello Rachael, thank you for writing in. Our research has found, there are several reasons why your dryer may not be drying correctly. Some situations that may cause your dryer to not heat properly include a lack of power, an issue with the size of the load or its wetness, an issue with the heating element, part number PS5574028 or a blown thermal fuse, part number PS2349395. We hope this helps.
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.