This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 6 hrs and your part ships today!
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
$72.93
In Stock
Order within the next 6 hrs and your part ships today!
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$69.34
In Stock
Order within the next 6 hrs and your part ships today!
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$110.95
In Stock
Order within the next 6 hrs and your part ships today!
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
$56.72
In Stock
Order within the next 6 hrs and your part ships today!
Order within the next 6 hrs and your part ships today!
Questions And Answers for ATW4676BQ1
Ask our experts a question about this model and we'll get back to you as soon as possible!
9 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Melinda
December 14, 2021
How do I reset this machine
For model number ATW4676BQ1
Hello Melinda, Thank you for the question. To rest the Washer, you just need to unplug the appliance for 5 mins. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bobby
February 19, 2022
Bangs when spinning jumps up and down like tub coming up hitting lid loud banging at end of each spin it is level
For model number ATW4676BQ1
Hello Bobby, Thank you for the question. We suggest checking the Suspension Rods for wear or damage. The Rods prevent the drum from moving and jumping around while in use. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Hello Wanda, thank you for the question. According to our research, we would recommend checking the drive belt, part number PS11747978, to fix the issue. We hope this helps!
Stopped in spin cycle. Water pumped out ok. Recently, before spin stopage problem, system made loud noise while spinning. Awhat is my problem?Thanks
For model number ATW4676BQ1
Hello Joseph, thank you for your question. That would probably be an issue with the actuator Part #: PS11769864. We would recommend replacing that part. I hope this helps!
Was this helpful?
Thank you for voting!
Cornell
February 29, 2024
Pump hose does pipe come with camps
For model number ATW4676BQ1
Hello Cornell, thank you for getting in touch. According to our research, the drain hose, part number PS12578897, for your model comes with the clamp. The tub to pump hose, part number PS11765836, does not come with the clamp. The tub to pump hose clamp is part number PS11740613. If you need help placing an order, customer service is open 7 days a week!
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
