Models
>
AE7133
AE7133 Dryer - Overview
Models starting with AE7133
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Multi Rib Belt
PartSelect #: PS11742271
Manufacturer #: WP40111201
This dryer drum belt from Amana has five ridges and is 93-3/8" inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber.
$12.04
In Stock
Door Catch Kit
PartSelect #: PS2162263
Manufacturer #: LA-1003
This kit comes in two pieces: the catch and the clip.
$41.24
In Stock
Idler Pulley Wheel with Bearing
PartSelect #: PS11757553
Manufacturer #: WPY54414
This two inch wide idler pulley wheel is beige in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center.
$28.46
In Stock
Door Switch Kit
PartSelect #: PS1964648
Manufacturer #: W10169313
This part replaces older two terminal switches.
$38.18
In Stock
Thrust Washer
PartSelect #: PS11740482
Manufacturer #: WP233520
This washer is 3/4 inches in diameter.
$10.14
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$6.91
In Stock
Retaining Ring
PartSelect #: PS11740487
Manufacturer #: WP23748
This metal retaining ring is well under an inch long. Use it for your Maytag brand clothes washer or your clothes dryer.
$17.32
In Stock
Spring Retaining Clip
PartSelect #: PS11739294
Manufacturer #: WP22001650
This front cover spring retaining clip is not quite an inch long. It is made entirely of metal and is used for some washing machines.
$14.15
In Stock
Hex Nut
PartSelect #: PS11742711
Manufacturer #: WP488130
Part may differ in appearance, but functions same as original.
$12.19
In Stock
Blower Wheel
PartSelect #: PS2052494
Manufacturer #: 56000
Part may differ in appearance, but functions same as original part.
$78.67
In Stock
Screw, 8-18 x 1/2
PartSelect #: PS11741443
Manufacturer #: WP3390631
This screw is sold individually.
$10.00
In Stock
Common Symptoms of models starting with AE7133
[Viewing 7 of 7]Noisy
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace drive belt
Remove front panel, lint basket, motor mounts,exhaust hood, front drum brackets. Then slip serpentine belt around drum, pressure w/ tension idler pulley and slip around drive motor spindle. Replace all parts in reverse order (a two person job).
Vacuumed inside of dryer (full of lint.)
Vacuumed inside of dryer (full of lint.)
Parts Used:
-
Robert from Skokie, IL
-
Difficulty Level:Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver
304 of 354 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Switch sticking in on position
FIRST unplug dryer from electrical source, CAUTION, the top of this dryer does not open with clips, do not pry on top to open! On the front of the dryer look under the lower panel, and find two screws, one on the left side, and one on the right, remove these screws, and pull slightly down on panel to remove. Behind this panel find two screws holding the door panel, one on the left, and one on the right, remove the left, and support the door panel while removing the right side. Gently pull the bottom of door panel outward, and the clips on top of door panel will unhinge from top, carefully rotate left side of door panel to floor, and note the wire connections on switch, and orientation of switch, then unplug wires, and move door panel to a comfortable working positon. Door must be open to remove switch, then depress the two plastic retaining keepers on each side of switch, and push switch through toward door. Replace with new switch, reconnect the wires, and reassymble in reverse order. Remember, door assymbly must be inserted in dryer top at an angle, and then bottom rotated downward, and bottom panel nylon guildes inserted into door panel bottom.
Parts Used:
-
Don from Jacksonville, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
99 of 133 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
catch mounted on door broke
The door had always opened with the wrong swing and it wasn't til I needed to repair this that I noticed you could change the swing. I changed the swing of the door and then noticed that the clip was included on both sides so i did not need to repair the catch. I still have the part so when it breaks again, I can just pop it in.
Parts Used:
-
Paul from Mt. Pleasant, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
93 of 123 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!