Models
>
6435A
6435A Norge Washer - Overview
Models starting with 6435A
Click on the best match to narrow your results.
- 6435A Norge Washer (WASHER)
- 6435A (REV D) Norge Washer (WASHER)
- 6435A (REV B) Norge Washer (WASHER)
- 6435A (REV C) Norge Washer (WASHER)
- 6435A (REV A) Norge Washer (WASHER)
- 6435A REV A Norge Washer (Norge Washing Machine Model 6435A REV A (6435AREVA) Parts)
- 6435A REV B Norge Washer (Norge Washing Machine Model 6435A REV B (6435AREVB) Parts)
- 6435A REV C Norge Washer (Norge Washing Machine Model 6435A REV C (6435AREVC) Parts)
- 6435A REV D Norge Washer (Norge Washing Machine Model 6435A REV D (6435AREVD) Parts)
Keep searches simple, eg. "belt" or "pump".
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
$11.68
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
This hose clamp is sold individually.
$14.16
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$6.91
In Stock
Screw
PartSelect #: PS11740978
Manufacturer #: WP3196164
This screw is sold individually.
$9.79
In Stock
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$27.46
In Stock
Lid Switch Actuator - Black
PartSelect #: PS11742355
Manufacturer #: WP43-0057
This is part of the lid switch actuator mechanism and activates the lid switch, when the lid is closed, to start the wash cycle and when the lid is open, it stops the cycle.
$72.73
In Stock
Affresh Washing Machine Cleaner - 3 pack
PartSelect #: PS1960673
Manufacturer #: W10135699
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
$16.07
In Stock
Leveling Leg and Pad
PartSelect #: PS2026623
Manufacturer #: 25001119
This part includes locknut.
No Longer Available
Leveling Leg and Pad
PartSelect #: PS11740563
Manufacturer #: WP25001119
This part includes locknut.
No Longer Available
Screw, 8-18 x 1/2
PartSelect #: PS11741443
Manufacturer #: WP3390631
This screw is sold individually.
$9.99
In Stock
Common Symptoms of models starting with 6435A
[Viewing 5 of 5]Leaking
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Intermittent problem with lid switch, no high speed spin/pump out
Disconnect power, unsnap and raise machine top cover w/lid, remove old switch - two screws under lid, taking care to not drop loose actuator lever into machine. Remove control panel back and disconnect switch wire connector. Intall new switch, taking care to not drop loose actuator lever into machine, connect switch wires inside control panel. Replace panel cover and lower machine top cover w/lid and snap into place, reconnect power, verify operation...
Parts Used:
-
Linda from La Porte, IN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
46 of 61 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of the water inlet vaqlve
First I disconnected the inlet hoses. After lifting up the cover the electrical wires were marked and disconnected from the old valve. Next the short hose from the old valve to the tub was removed. Then the old valve was removed from the washing machine by removal of two mounting screws. The new valve was installed in the reverse order. New hose clamps were installed on the short hose from the valve to the tub. New washers were installed on the hoses which connected to the valve. A test was made to check for any leaks.
Parts Used:
-
William from Chester, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
11 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid switch had deteriated over time and no longer made contact
removed the screw holding the actuator, ordered the new part and replaced it when it arrived. Shipping was really fast and I even received it one day early.
Parts Used:
-
James from Rochester, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!