This thermal cut-off kit for a dryer includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse (309 degrees). This kit also includes flat heaters with jumper wires.
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
This high-limit thermostat with Terminal Extension Arm acts as as safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches 221 degrees Fahrenheit, this piece will shu...
The blower wheel is a squirrel cage type wheel whose purpose is to move the air through the room or appliance. The blower wheel spins on the motor shaft to blow air through the dryer drum and out through the exhaust.
This is a replacement bearing ring kit for your dryer. The bearing rings are found on the top and bottom lips of the dryer drum. If your dryer is unusually noisy, or the drum will not turn during oper...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Rodney
December 8, 2019
It’s showing i can’t get a heating element for this model??
For model number 11065102310
Hello Rodney,
Thank you for your question. The heating element for your model is under part PS334313. Hope this helps!
The door has a seal that was slightly torn and then a shirt got caught in it ripping it off the door. I hope to replace it
For model number 11065102310
Hi Marjorie,
Thank you for your question. The part number listed under your model number for the door seal is PS11766744. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Ray
March 1, 2023
There are 2vents with holes on the back panel. One has rust and sharp edges on the holes. Can this vent be replaced. It is on the left side of back panel.
For model number 11065102310
Hi Ray, thank you for contacting us. If the back panel has rust and sharp edges on the holes we would recommend replacing it with part number PS896465. The rear panel covers the wiring and other components at the back of the dryer. We hope this solves your problem!
Why are there two thermostats under this model? Are there two in the dryer? If there is one, how do I know which one to use?
For model number 11065102310
Hello Rose, thank you for the great question. We have found that your model comes in 2 different thermostats. The one is cycling thermostat, part number PS11741405. The cycling thermostat monitors and regulates the temperature inside the dryer. And the other one is a high-limit thermostat, part number PS11742185. The high-limit thermostat shuts off the heating element or burner when the dryer overheats. You may need to replace the one that is faulty. We hope this information is useful!
First tried heating element and thermal fuse with no luck. Ordered thermal cutoff and fixed problem. Had I used an ohm meter first I would have determined problem before having ordered heating element and fuse, as both had resistance. I wast just lazy and ordered the took the most common failed components first before taking dryer back off.
I ordered all the thermal sensors for the dryer. They arrived two days later and they were the correct parts. It took me about 1/2 hour to replace all three sensors and now the dryer works like new again. My wife was very pleased, so was I.
I basically took the back offo the drive, then detach the heating coil. Afterwards had to go back in and change the thermal regulator an the job was completed.