Troubleshooting
This part fixes the following symptoms:
Little to no heat when baking | Oven is too hot | Touchpad does not respond | Little to no heat when broiling
This part works with the following products:
Range.
This part works with the following products:
Frigidaire.
Part# 5304495520 replaces these:
AP5807223, 316560105
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Laureta P - November 10, 2020
Verified Purchase
Worked perfect
The part arrived the next day and it was so easy to install. Saved me 200$.
Shelley B - July 3, 2020
Verified Purchase
Easy repair
easy repair works as described
Leo O - May 27, 2020
Verified Purchase
Better packaging and some instructions
Well, I was not impressed with how it was packed. It was into a plastic bubble wrap and in box which was too big so consequently the part was loose in the box and bouncing from side to side. More bubble wrap or some Styrofoam would have corrected the problem.Also when I took the part out of the box at first I could not figure out that I had to remove the front label off the old part and stick it onto the new part. It would have been nice if there was some instructions with it to tell me to do this. I had to figure this out on my own. Other than that it seems to be okay.
Cheryl W - November 13, 2019
Verified Purchase
Worked great easy to install
We received the order quickly and repair was completed in an hour. It was easy to order and find part on website
Florin F - April 19, 2019
Verified Purchase
easy to replace.Part received as expected
I finally have the oven working. It wasn't the sensor, it was the electronic board of course.
Majid I - April 5, 2019
Verified Purchase
Oven range
Works perfect fast delivery service
Mike I - January 14, 2019
Verified Purchase
Easy repair
Very easy to replace this part it takes about 10 minutes
Sharron C - October 23, 2018
Verified Purchase
Speedy delivery
The part arrived well packaged. Delivery was great, shipping cost reasonable. Part as described and it excellent working condition. Part easy to replace and done without costly service charges from repair tech.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.5 / 5.0, 4 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven temp runaway tempreture, oven light out, sensor was changed for temp drifting low
The light and sensor were straight forward and easy. The EOC was as well but there was one glitch. You have to also purchase the black panel overlay, you cannot use the old one. While the adhesive will still adhere, the keypad is different and REQUIRES the new cover. This would have been good to know when I ordered parts as I did not know until I got the three parts and had to reorder the overlay creating a weeks delay in it's repair.
Other Parts Used:
-
Kenneth from LIBERTY, MO
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Runaway heating during warmup
Initially replaced the thermostat and the problem continued. Website was spot-on with follow-up procedures and ordered the ECB. Installation was simple. Of particular note is that the digital touch pad from the old unit must be removed and reinstalled on the new one BEFORE you install it. Remove the old touch pad carefully as the sticky backing will peel off the black paint on the back of the touch pad and reveal the circuitry board on the new ECB. Other than that, the process was a simple "plug in and go" install. Super easy!
Other Parts Used:
-
Vic from LACEY, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven control board went bad
ordered control board from PARTSELECT if you need it fast over night it remove rear of back guard with NUTDRIVER 4 phylips screws hold the control board in place it helps if you have a phone to take pictures to see where the wires go when you connect them to the new board the overlay is not to hard you have to make sure to start at one end and get the end lined up use your fingers to feel the edge of the control board at one end put overlay in place and gently lay it in place and start laying it down slowly making sure it is going strieght once your at the other end and its down i used a soft cloth to press it down across the face and happy to say the syove is working once again
Other Parts Used:
-
Robert from SCRANTON, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electronic Control Board Oven not heating timely or at all.
Watched You Tube 3 times. Removed the stove back covers top and bottom.
Ordered the new electronic control board and overlay.
Took picture of existing control board and connections.
Viewed parts select online schematic of the stove, make and model.
Ordered the new black overlay, did not want to take time to try to save old black overly.
Parts arrived.
Re-watched You Tube.
Installed the new electronic control board and included electronic filter as per You Tube.
Tested the oven.
Works like new.
Saved $ 200 to $ 300.
Great fun.
Hero to my wife !
Ordered the new electronic control board and overlay.
Took picture of existing control board and connections.
Viewed parts select online schematic of the stove, make and model.
Ordered the new black overlay, did not want to take time to try to save old black overly.
Parts arrived.
Re-watched You Tube.
Installed the new electronic control board and included electronic filter as per You Tube.
Tested the oven.
Works like new.
Saved $ 200 to $ 300.
Great fun.
Hero to my wife !
Other Parts Used:
-
Charles from AURORA, CO
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gentry Wade
December 7, 2018
Error message f11 & f12. Continuous beeping
For model number LGEF3045KFN
Hello Gentry, thank you for your question. The F11 code in regards to a bad touch pad connection. We would recommend replacing the touch pad and board which are part numbers Part Number: PS2364031, and Part Number: PS9494055. The F12 is in relation to the board/oven sensor. We would recommend testing the sensor part number PartSelect Number PS11731755. With the probe at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080–1090 ohms at room temperature. If the sensor is not within that range it should be replaced as well. I Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Brian
November 8, 2017
The buzzer for the time will just start buzzing all different times of the day. Do i need a whole new control board? Or is there a separate part for this. My oven is only two years old and it’s very disappointing that i bought all Frigidaire appliances and i’m already having issues. Thanks for any help you could provide me.
For model number LGEF3045KFK
Hi Brian,
Thank you for your inquiry. If the buzzer on your oven is constantly going off, hit the cancel button to see if that helps. If not hit the timer off button. If this does not work try unplugging the oven or turning the power off to it for a few moments to see if this helps. If not you may have to check the touchpad, the wiring between the touchpad and the electronic control board and the electronic control board to see which part is causing the issue. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Ryan
February 26, 2018
Where do I buy the electronic overlay I need a new one.
For model number LGEF3045KFC
Hello Ryan, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is Part Number: PS2364031 for the Overlay and the electronic board behind the overlay is Part Number: PS9494055. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Marla
October 16, 2019
When the oven is plugged in the broiler automatically comes and and will only shut off if the fuse breaker is turned off. “pf” message is displayed. What could be causing this?
For model number 665.95829003
Hello Marla, thank you for your question. The most likely issue is the main oven control board, PartSelect Number: PS11746059. We would recommend replacing this part. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Allen
December 13, 2019
My oven and display do not work after power surge,but all 4 eyes work on top. I have disconnected power cord and replugged ,but still the panel and oven do not work. I have removed the rear top panel and do not see any loose wires or melted wires. Does this model have a fuse or reset button/switch. Thanks.
For model number LGEF3045KFJ
Hello Allen, Thank you for the question. In this case the surge may have caused the Control Board to burn out and it will need to be replaced. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Randy
June 30, 2021
My oven temp goes up on its own. It will not shut off I have to un plug it. What part do I need. And is it easy to do myself
For model number CGEF3055KBA
Hello Randy, Thank you for the question. This is normally an indication the Oven Electric Control Board is defective and will need to be replaced. We hope this helps, good luck with this repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Patricia
January 6, 2020
Puting out code 11
For model number LGEF3045KFK
Hello Patricia,
Thank you for your question. The F11 error code means there was a shortage on the control board touch pad, we suggest unplugging the oven for two minutes to reset it and then see if there is any change, if not then the control board would need to be replaced under part PS9494055 for your model. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
RAYMOND
April 5, 2023
The clock started gaining time and can't set it.
For model number LGEF3045KFH
Hi Raymond, thank you for contacting us. Based on our research, the issue is probably due to the control board, part number PS9494055. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Adren
April 29, 2023
The stove does not heat or broil. The small fan comes on inside the oven. I have test both the broil and oven elements and they are fine. I have tested the power to the stove and it is fine. The clock displays and when I turn on the oven the temperature displays as if it were doing something. However, the display showing the fan turning does not appear for both broil and normal oven use. I think the board is bad but I'm not sure.
For model number LGEF3045KFC
Hello Adren, thank you for getting in touch. Based on our understanding of the issue, we would suggest you replace the oven control board, part number PS9494055, to fix the issue. We hope this information is useful!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Steve
November 8, 2019
The oven heats very slowly at about 1 degree per minute. I noticed that the broil element was not heating at all, and when i pulled the bottom pan, i was also able to verify that the bottom element is not heating either. Yet the oven will eventually reach 250 degrees after about three hours. What is the source of the heat that is occurring, and what part(s) need to be replaced to fix this problem? Does the convection fan have a small heating element? Thanks much for your help!
For model number FGEF3044KFB
Hello Steve,
Thank you for your question. The part our sources recommend is under part PS1528542 for your model. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- 3
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS9494055
Manufacturer Part Number: 5304495520
Manufacturer Part Number: 5304495520
Brand
Model Number
Description