Product Description
Replacement Ice Maker Specifications
This part is the replacement heat-release ice maker unit only. This kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female and one round male connectors.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Refrigerator Replacement Ice Maker
Troubleshooting
This part fixes the following symptoms:
Ice maker not making ice | Ice maker won’t dispense ice | Leaking | Noisy
This part works with the following products:
Refrigerator, Freezer, Ice Maker.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Westinghouse.
Part# 5303918277 replaces these:
AP3160597, 941760, 5303918277, 218226700, 218699501, 218713500, 240352401, 240352403, 3206306, 5303291912, 5303918277
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Denise C - May 10, 2021
Verified Purchase
The part arrived very fast and it was the right part.
Great quick service very happy!
Andre' D - April 14, 2021
Verified Purchase
Part worked well
I installed it and we have ice again.
Steve J - February 3, 2021
Verified Purchase
Easy Repair
Pulled out the old broken one, put in the new one. Adjusted the screw as per instructions. Waited a couple of hours - nothing ??? Removed the cover and turned the plastic wheel until it started running on its own. Works great now !
Claudia M - October 29, 2020
Verified Purchase
Works as expected!
The Ice Maker works great!! It was very helpful to get the video and watch how to install it. In addition it was very easy to order the part online. I received it very quickly. The entire process from order to replacement was so easy. I love my new ice maker!
Barry D - July 4, 2020
Verified Purchase
Ice maker replacement
This is about the fourth time i have used this site. Parts have always arrrived quickly. The repair went smooth and am very happy with all.
Edward A - July 4, 2020
Verified Purchase
Worked was expected
Easy install, arrived faster than expected in good condition and making ice within the hour.
Deanna N - June 12, 2019
Verified Purchase
Easy
Ordered part received in no time and installed.....working great....Thanks
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 4.0 / 5.0, 50 reviews.
What's this?
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Ice Maker Stopped Working
It was pretty straight forward. Remove the two screws that hold the unit to the wall of the freezer. In my case, I had to use a different ice maker than what came with the frig. In order to install the replacement unit they sent a wire adaptor so it would attach to the existing wiring. That too was all fine and dandy. The only problem was that the end of the wire adaptor did not fit through the existing hole in the rear of the frig. I used a utility knife to cut through the thin metal lining. That worked just fine. However, I could not cut through the insulation because I could not reach it through the small hole. The excess wire was supposed to be pulled through the hole and out through the back of the unit. So now the excess is between the wall of the freezer and the insulation. The unit is working wonderfully. In fact, it is making more ice than I can use. I am very pleased with the replacement unit. This is the 3rd ice maker that has been in this frig. All the others had a design flaw that had a leak in the rear of the unit. This caused all the ice to form into a big block. The replacement unit has not had this problem so far. Thank you for allowing me to explain my situation so that maybe others may benifit from my experience. Thank you. Jack
Other Parts Used:
-
JACK from MESA, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
163 of 180 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker died!
The repair for this was very simple, although it was a tight squeeze. The model I replaced the ice maker on was a side by side. First I removed the ice bucket so I could have more room to work with. Then I unscrewed 2 screws on the left side wall holding the ice maker in place. These screws had a 1/4" nut top on them so I used my socket driver for this. Then a quick disconnect of the wiring harness. Very Simple. I did the reverse to install the new unit. Total time was around 5 minutes or so. I now have ice again.
Other Parts Used:
-
John from Las Vegas, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
45 of 49 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old ice maker had stopped working properly. The cycle was inconsistent, and inlet water would run over existing cubes in the tray, before they were dumped into the dispenser box.
This was really simple, much like changing a light bulb. Two bolts loosened beneath the old unit to allow it to be lifted off and free. The power supply plug was easily disconnected. The new unit was then placed onto the loosened bolts, power supply reconnected and secured with the supplied wire tie. A small angled bracket was removed from the old and reattached to the new as a support toward the from of the unit. The cycle adjuster was backed off a 1/2 turn as per the instructions....and the next morning....new automatic ice. Life is good!
Other Parts Used:
-
Daniel from Baldwin City, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
28 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old icemaker would not cycle to make ice.
I had already removed the ice maker by loosening the two screws with a 1/4" nut driver, in order to compare the design and style to the intended replacement for size and critical measurements. The replacement was almost identical. The wiring harness was 2-3" longer than the original, but after snaping the wire plugs together I simply curved the wire up and to the left to be out of the way. The hanging brackets are slotted and it was easiest to slip the back hanger over the head of the screw and let it slip down, then the front hanger was already to line up even though you can't see the screw with the ice maker in the way. I had to transfer an L-shaped metal bracket to the bottom side, matching the old assembly, and adjusting it to hold the bottom side away from the freezer compartment a little so it would hang level and secure. You have to snug the two screws with a screw driver or 1/4" nut driver by feel, since you can't see them with the icemaker in place. It took about 10 minutes to take out the old and another 10 to put in the new. We now have a full bin of ice, and the old plastic trays have been retired. I should have done this a year ago.
Other Parts Used:
-
David from Cedar City, UT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
24 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water in the ice bin freezing all the existing ice into clumps
You have to blindly unscrew the two screws along the side of the ice maker. Once that is done simply remove the ice maker to the side to gain access to the electrical plug. Undo the plug and remove the ice maker completely. Install the adapter on the new ice maker and install it in much the same way you removed the old. I started the (2) 1/4" screws before installing the new ice maker to make it easier to hang. Pay careful attention to the wire harness and dress it out of the way. Finally tighten the two screws and make sure the bail wire is down to begin ice making once again.
Other Parts Used:
-
John from Mount Royal, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
20 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Our Ice Maker drove us nuts with noise from cubes getting stuck.
I purchased the replacement part (no instructions sheet) from another company, not this one, that cost 2X's a much as this company. So I sent it back and ordered from this company. Got it faster then the post office sends us the stamps we order by internet and this ice maker had instructions.
Our's is a side by side refrig, so working space is limited but do-able. The old ice maker has made a clicking noise for years while trying to push the cubes out of the tray. They would get stuck and refreeze, sticking half way out of the tray.
I loosened the 2 screws with a socket driver (which are difficult to see), raised the unit up and off the screws. Unplugged the power & out it came. Removed the bracket on the side as instructed to attach to the new ice maker and in the trash the ol' ice maker went. Set the new ice maker on the screws, plugged in the power, tightened the screws and walla. A quiet ice maker. In fact, it would startle us the first day as we didn't hear the clicking noise indicating it was stuck. All of a sudden the cubes just dropped into the container. Alright! Don't know why I didn't do this years ago.
Our's is a side by side refrig, so working space is limited but do-able. The old ice maker has made a clicking noise for years while trying to push the cubes out of the tray. They would get stuck and refreeze, sticking half way out of the tray.
I loosened the 2 screws with a socket driver (which are difficult to see), raised the unit up and off the screws. Unplugged the power & out it came. Removed the bracket on the side as instructed to attach to the new ice maker and in the trash the ol' ice maker went. Set the new ice maker on the screws, plugged in the power, tightened the screws and walla. A quiet ice maker. In fact, it would startle us the first day as we didn't hear the clicking noise indicating it was stuck. All of a sudden the cubes just dropped into the container. Alright! Don't know why I didn't do this years ago.
Other Parts Used:
-
Dee from Central Point, OR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
17 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Would Not Work - But Water Disp Did
Shut off water/power - pulled tray -loosened two screws holding ice maker - lifted it up and off - unhooked power connection installed new maker in reverse of above - power supply line was much to long but just pushed it under the ice tray ( away from the maker ) prior to ordering looked at comments from others regarding installation
Other Parts Used:
-
JAMES from HENDERSON, NV
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
17 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker burned out
Removing the old unit was easy enough, just loosened two screws that attach unit to side of freezer and disconnected the wiring harness. But the new unit never goes in quite as easily because it's always just a little different from the original. In this case, the wiring ended up being about six inches longer and the excess had to be stuffed behind a shield at the rear of the unit. Theoretically, the wire could have been pushed back through the opening, but it got jammed and wouldn't go. I had to remove side rails and pry the shield forward in order to get the wiring back out of the way. The unit is a narrow side by side, so there wasn't a lot of room to move around. But it wasn't difficult, just tedious. I had to make sure the wiring did not come into contact with the heating element at the bottom of the icemaker. Once installed it worked great.
Other Parts Used:
-
John from Alexandria, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
17 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker would not make ice
un plug fridge. removed ice maker from fridge. loosen 2 mounting screws. lift unit in slots to get over heads of screws. unplug wire harness. remove cover. remove 3 screws from control housing. remove 2 motor mounting screws. unplug motor wires from switches w/needle nose. installation is the reverse. plug in fridge turn on icemaker. takes 10 to 15 min to start to cycle.
easy and cheaper than new fridge or ice maker
easy and cheaper than new fridge or ice maker
Other Parts Used:
-
paul from traer, IA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
16 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice make just stopped
I want to first say that before I ordered this part from "Part Select" I first went and talked with a local appliance repair shop. They quoted me a $120 charge to come out and check the problem. Then $30 and hour service fee, plus parts. He provided me a quote of about $250 for the job.
I found this part easily on the web site $77. It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.
I found this part easily on the web site $77. It was very easy to instal. The only problem I had was the fact that in the side by side it was very difficult for me to get two hands inside the freezer to install it. (I have wide shoulders). Two screws loosened, no need to remove them. Just life the entire unit straight up. Unplug wire harness. Then just reverse order. Could not be easier. If you can change a light bulb you can do this.
Other Parts Used:
-
David from Beavercreek, OH
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
16 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- 3
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Norman
November 30, 2017
My icemaker (part no. 241642511) is slightly overfilling and the cubes are stuck together. I noticed an adjusting screw after removing the cover and indicates + and -. Which way is screw turned to reduce the amount of water dispensed.
For model number FRS3R5ESB3
Hi Norman,
Thank you for contacting us. I believe that perhaps turning it toward the - would lessen the flow of water. I hope that helps. Good luck with your repair.
16 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
April 11, 2018
How do i check if the water inlet valve is operating properly!
Hi Michael,
Thank you for your question. Before you begin to test your icemaker's water inlet valve, make sure you disconnect the appliance's power supply. The easiest way to do this is to unplug the unit from the wall. Alternatively, you could trip the appropriate switch in the circuit breaker panel, or you could remove the appropriate fuse from your home's fuse box.
Consult with an appliance repair technician if you do not feel you have the skill or the ability to successfully complete this test.
Locate your icemaker's water inlet valve, it is typically located behind a refrigerator. Gently pull your refrigerator away from the wall. You may want to place scraps of carpet, of some other soft material below the fridge to prevent damage to the floor. Turn of the water valve's water supply by closing the shut-off valve in the waterline leading to the water valve. Remove the lower access panel on the back of the refrigerator using a screwdriver or a nut driver.
Place a container under the valve to catch any water that may spill from the water valve and its fill tube. Remove the water valve's fill tubing. Loosen the flare nut on the brass fitting that is found on the inlet side of the water valve. You can use a wrench to loosen the flare nut.
Your water inlet valve is held in place on your refrigerator by means of a metal bracket. Use a screwdriver or a nutdriver to remove the screw that holds the water valve's bracket to the refrigerator cabinet. Gently pull the water valve out of the cabinet, and remove the tube from the outlet port.
There are two wires connecting to the terminals of your water inlet valve. If yours is a double solenoid water valve, it will have four wires. Be sure to label each wire so that you know where to reconnect them later. Firmly grasp the metal connector of the wires in order to remove the wires. You may need to use a pair of needle-nosed pliers. Do not pull on the wires themselves.
Set your multitester to the R X 1 ohms setting to test for continuity. Place each of the multitester's leads on a terminal. Your multitester should display a reading between 200 and 500 ohms. Closely examine your water inlet valve. The exact ohm resistance rating you should test for may be marked on the valve.
If the test you conduct with your icemaker water inlet valve does not produce these results, then you should replace the component. I hope this helps. Thank you and have a great day!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Elias
October 11, 2017
I have a Frigidaire fridge/freezer combo purchased in 2009. I have watched the video and read most of the comments associated with this replacement ice maker, but no one seems to have the problem I am having.My problem is not that the ice maker will not make ice. It does that really well. Our ice maker tries to spit out ice at any old random time.We'll sit down for dinner and all of a sudden the thing starts spitting out ice.The downspout on the freezer door is closed so the ice does not spill on the ground but gets backed up in the freezer so that when you open it and try to fix it, a whole bunch of ice dumps on the ground.The only way i have been able to fix this is by trying to defrost the back section.Somehow it stops after that.What is broken on my unit?Please help.
For model number Glhs66eeb4
Hi Elisa, Thank you for the question. Sounds like you need the Dispenser Switch Board,PartSelect Number PS1526487. It is also to take the front off the dispenser and check the Ribbon Cable Harness,PartSelect Number PS1526364. Normally it is one of the two parts.Hope this helps!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Tim
November 14, 2017
What is the difference in this ice maker and the one that comes in your kit # ps10057479?This is $103 and the kit with valve is only $98 or so.
For model number E32AF75FPS0
Hi Tim,
Thank you for your inquiry. The replacement ice maker, part number PS735469, replaces the heat-release ice maker unit only. The kit comes with four round female connectors at the end of the wire harness. It also comes with the adaptor that converts the harness to three round female, and one round male connectors. The add on ice maker assembly, part number PS10057479, includes an icemaker that makes eight radius ice cubes, the water valve, an ice bucket, the fill tube, the harness, and installation instructions. Note: This icemaker assembly will fit most Frigidaire models manufactured from 2001 to present. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Eddie
March 3, 2018
Ice maker doesn't any make ice. Inlet valve works perfect. It can be fix or needs to be replaced??thank you
For model number FFHS2622MWF
Hello Eddie, Thank you for your inquiry. It could be the ice maker or the ice maker control. Most heat release ice makers will have a removable cover at the front. Behind the cover is a series of electrical test points that can be used to diagnose the ice maker. The unit can be manually operated by inserting an insulated jumper wire into test points “T” and “H” to initiate a “test harvest”. The jumper should be insulated 14 gauge solid wire that has the insulation stripped back about 3/4 of an inch on both ends, and bent into a “U” shape. When inserted into the test points for 5 to 10 seconds, the motor should start and the cycle will continue on its own. You may have to manually close the freezer door switch for this to operate.
This test will simulate a real harvest cycle and will operate the ejector blades, shut off arm and the fill valve in the proper sequence, and will allow you to do a proper diagnosis. This is a live voltage test and should only be performed by a qualified person. If the motor does not start, you can verify that you have power to the ice maker at test points “L” and “N”. If the ice maker is getting power and does not perform a cycle, then the ice maker will need to be replaced since the module comes as part of the ice maker assembly. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
William
September 20, 2019
Water leak inside freezer at the back where icemaker connects runs down back of the inside of freezer
For model number FRS26H5ASB4
Hello William, Thank you for the question. I suggest checking the Water Fill Tube PartSelect Number PS7783975. This tube fills the ice maker mold. Make sure it is not damaged or cracked and causing the leak or just need to be readjusted into the correct position. Also make sure the ice maker is not over filling and causing it to overflow and leak. If this is the case you may need to replace the Water Valve Part #: PS7784018. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Gil
October 31, 2019
Hello, my ice maker shutoff lever stopped working, when I put it up in off position the ice maker is still making ice, which means ice is piling up. How do I stop it?Thanks
For model number WWSS2601KW
Hello Gil, Thank you for the question. Unfortunately this would indicate the Ice maker is defective and will need to be replaced. Thank you for your inquiry, good luck with this repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
EDDIE
March 6, 2018
Hi. What's the part number for the ice maker to model number ffhs2622mwf. So i can ordered and replaced myself. Thank you
For model number model number FFHS2622MWF
Hello Eddie, thank you for your question. The icemaker replacement for your specific unit is part number 241798224. Please enter the part number into the site for current price and availability. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
George
January 21, 2019
Is there a curtain way that the connector has to plug in left right or right left to line up same color wires, also why do you need to turn the screw on the new icemaker a half turn to the left.
For model number ffhs2611LW0
Hello George , Thank you for the question. There is no right to left for the harness, you just need to plug it in. You turn the screw half way to adjust the timer as explained in the video. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Gene
April 12, 2018
Is a repaclement ice maker dispenser unit still available for this older model? The auger will not feed the ice to the door and it appears the end bushing has broken loose from the bin.
For model number GLRS264ZA
Hi Gene,
Thank you for your question. If the auger will not feed the ice to the door and the end bushing has broken loose from the bin, we can provide you with a new ice container with auger. The part number listed under your model number for the ice container with auger is PS1991428. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- 2
- 3
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS735469
Manufacturer Part Number: 5303918277
Manufacturer Part Number: 5303918277
Brand
Model Number
Description