Frigidaire 5308000010 - Evaporator Fan Blade | PartSelect.ca
Evaporator Fan Blade – Part Number: 5308000010
( Grid squares measure 1x1 inch )
Evaporator Fan Blade – Part Number: 5308000010 Evaporator Fan Blade – Part Number: 5308000010 Evaporator Fan Blade – Part Number: 5308000010 https://partselectca.azureedge.net/Schematics/Frigidaire/UXRVGK3I.gif

Evaporator Fan Blade

Your Price

CAD$46.40
In Stock

PartSelect Number PS473177
Manufacturer Part Number 5308000010
Manufactured by Frigidaire

This part works with the following brands: Frigidaire, Kenmore, Gibson, Kelvinator, Crosley, Electrolux, Westinghouse, Tappan, Uni.

This part works with the following products: Refrigerator, Freezer.

This part fixes the following symptoms: Noisy | Fridge too warm

Videos For installing this part.

Questions & Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Comstock
August 27, 2017
Is there video to walk me through this process? What tools are required?
For model number FRS26RC3JS3
Hi Comstock, Thank you for the question, The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers. Here is a link to our video. https://www.youtube.com/watch?v=Hj_ojPQebcw Hope this helps!

3 people found this helpful.

Was this helpful?
Pamela
November 24, 2017
Hi I recently purchased the defrost kit from you and it seemed to work immediately for about two weeks. Now I am experiencing the same issues as before. Fridge and freezer are too warm and a clicking sound was being heard, frost has built up on the bottom half of the freezer panel in this short time. What would be my next step?
For model number flsc238js1
Hi Pamela, Thank you for the question. With the information provided, you may have an issue with the Main Power Control Board,PartSelect Number: PS2339026.You can also test the Defrost Thermostat. The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!

2 people found this helpful.

Was this helpful?
Earl
December 11, 2017
Evaporator fan making noise.
For model number FFHS2611WHA
Hi Earl, Thank you for the question. If the fan is making noise, I suggest having it replaced. Good luck with the repair!

2 people found this helpful.

Was this helpful?
Mary
August 4, 2018
Lights are on and i hear refridgerator running but it does not cool down at all and then it shuts off
For model number 25370413414
Hi Mary, Thank you for your question. If the refrigerator is too warm, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the evaporator fan blade, the evaporator fan motor, the temperature sensor and the filter-drier. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Phay
November 21, 2018
Hello, is this fan blade (evaporator fan blade 5308000010) compatible with the evaporator fan motor kit 5300158289?Thank-you
Hello Phay, thank you for your question. Yes, the blade part number 5308000010 is compatible with that fan motor. Good luck with your repair!

1 person found this helpful.

Was this helpful?
Gerald
June 26, 2019
Have ice build up behind panels in back of freezer side. Ice hits fan and noise starts. Fan works but wondered if thermostat would be problem. Have had sy ef reading on control board but unplugged and defrosted and went back to working.
For model number FGHS2631PE3
Hello Gerald, Thank you for the question. I suggest testing the Defrost Thermostat Kit, PartSelect Number PS469522. The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!

1 person found this helpful.

Was this helpful?
Related Parts

Defrost Thermostat Kit

CAD$23.48
In Stock
Jerry Burkhart
October 2, 2019
Is this freezer. Frost free?
For model number FFU1466GW1
Hello Jerry, thank you for writing. A frost buildup can occur from either a faulty Defrost Thermostat, part number PS2350702, or Timer, part number PS12585793 for your model. Good luck with your repair!

1 person found this helpful.

Was this helpful?
Joanne
February 13, 2020
Fridge and freezer will not sustain correct temperatures, keeps defaulting to 'h' or '1' and '1'
For model number FFHS2322MBLA
Hello Joanne, thank you for writing. We advise checking the Run Capacitor. When testing a capacitor with a multimeter, you will need to set the meter between 10K and 1m ohms. Touch the leads from the multimeter to the corresponding leads on the capacitor. The red lead to positive and the black lead to the negative. The meter should start at zero and then moving slowly toward infinity. This means that the capacitor is in working condition. If the meter stays at zero, the capacitor is not charging through the battery of the meter, meaning it is not working. I hope this helps.

Was this helpful?
Jerry
August 5, 2019
Frezzer will not defrost
For model number fphb2899lfb
Hello Jerry, thank you for contacting us. You will want to replace the Defrost Heater part number PS2369212 for your model. Good luck with your repair!

Was this helpful?
Laura
September 24, 2019
I'm getting a sound which sounds like a wail, then settles into a normal fan sound after about 20 seconds. It's getting more frequent so something is wearing out. Is this just the evaporator fan slipping on the motor shaft or the fan motor? I haven't noticed the freezer/fridge not keeping proper temperature.
For model number FRS26KF6EMK Fridge
Hello Laura thank you for writing . It sound more like the motor is wearing out You should be able to test this with a multimeter. motor Part Number : PS11726595 is in the list of compatible items for your model. Hope this helps . Please contact us anytime.

Was this helpful?

Customer Repair Stories

Average Repair Rating: 3.3 / 5.0, 4 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Jordan from Maumee, OH
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver
Parts Used:
5308000010, 5300158289
Noisy fan
1. Removed the 7 nuts using the nut driver from the freezer back panel inside the freezer.
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including the brackets.
6. Install the new motor and fan onto the mounting bracket.
6a. Attach the green ground to the mounting bracket.
7. Screw the two gold screws back into the freezer.
8. Attach the new wiring harness. Note, the old harness had a mounting hole/space for it to connect to the wiring harness of the freezer. The new motor's harness was not long enough for this, so it is connected freely to the freezer harness.
9. Use the hair dryer to melt any ice that may have formed on the coils and hole where the fan goes.
10. Turn the freezer on to see if the fan turns on.
11. Reinstall the back panel.
All done!
144 of 166 people found this instruction helpful.
Was this instruction helpful to you?
keith from villa rica, GA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
5303918549, 5303918476, 5308000010
lighting hit the house
first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered,
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts
30 of 56 people found this instruction helpful.
Was this instruction helpful to you?
ROY from PENSACOLA, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
Parts Used:
5308000010, 5300158289
The Evaporator Fan Burnt Up
The fan motor all but caught the inside of the freezer on fire . Had to remove then clean, and I mean clean the walls of the freezer . Then had to pry out the old fan without breaking anything . Replacement of new fan was quick and easy because all the parts that I needed were in the bag
26 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Greg from NAVARRE, FL
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
Parts Used:
5304436055, 5308000010
Freezer making annoying high pitched sound (like a whine)
Parts Select included a video, and I watched a couple more that were on YouTube. Watch the video and do the repair . . . it's very easy took me about 35 min once I got the freezer emptied, including cleaning the freezer. I used a Philips head screw driver and I think it was a 5/16 nut driver . . . you can do this. Freezer running fine, no noise. One thing I would be careful on is removing the back plate that covers the fan and motor, the edges can be sharp and you could cut yourself removing the back plate. Also don't try to put the rubber gasket in before you replace the back plate, install the back plate and the rubber gasket goes in easy peasy :)
1 person found this instruction helpful.
Was this instruction helpful to you?

Model Cross Reference

Brand
Model Number
Description
Frigidaire
15304-0A
Refrigerator - REFRIGERATOR
Frigidaire
15304-7A
Refrigerator - REFRIGERATOR
Frigidaire
177040A
Refrigerator - REFRIGERATOR
Frigidaire
177047A
Refrigerator - REFRIGERATOR
Frigidaire
17714-0A
Refrigerator - REFRIGERATOR
Frigidaire
17714-7A
Refrigerator - REFRIGERATOR
Frigidaire
178040A
Refrigerator - REFRIGERATOR
Frigidaire
178047A
Refrigerator - REFRIGERATOR
Kenmore
25314772100
Freezer
Kenmore
25314772101
Freezer
Kenmore
25314772102
Freezer
Kenmore
25314772103
Freezer
Kenmore
25316562100
Freezer
Kenmore
25316562101
Freezer
Kenmore
25316572100
Freezer
Kenmore
25316572101
Freezer
Kenmore
25321021100
Freezer
Kenmore
25321021101
Freezer
Kenmore
25321021102
Freezer
Kenmore
25321021103
Freezer
Kenmore
25321021104
Freezer - UPRIGHT FREEZER
Kenmore
25321021105
Freezer
Kenmore
25321041100
Freezer
Kenmore
25321041101
Freezer
Kenmore
25321041102
Freezer
Kenmore
25321041103
Freezer
Kenmore
25321041104
Freezer
Kenmore
25321041105
Freezer
Kenmore
25321041107
Freezer
Kenmore
25321041108
Freezer

All brand logos are trademarks of their respective owners.

The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.

Copyright © 1999-2021, Eldis Group Partnership. All rights reserved.