Part Location Diagram of 5303281153 Frigidaire Rear Drum Bearing Kit
See part 30 in the diagram
Replacing your Frigidaire Dryer Rear Drum Bearing Kit
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Rear Drum Bearing Kit

★★★★★
★★★★★
60 Reviews
$73.24
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS459829
Manufacturer Part Number 5303281153
Manufactured by Frigidaire
Product Description

Rear Drum Bearing Kit Specifications

This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Dryer Rear Drum Bearing Kit

Replacing your Frigidaire Dryer Rear Drum Bearing Kit
Troubleshooting
This part fixes the following symptoms:
Noisy | Marks left on clothes
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Kelvinator.
Part# 5303281153 replaces these:
AP2142648, 1851, 5303281153, 08015113, 08015324, 131378400, 131777700, 137088600, 137088620, 137088630, 3281019, 3281020, 3281153, 5303281019, 5303281020, 5303281153, 5303286875, 8015113, 8015324, 902088 ... Show more , Q000022224, Q000142850, Q000500537, Q142850, WQ142850, WQ22224, WQ500537 Show less
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
60 Reviews
4.8
Filter By Rating:
  • 5 Stars
    51
  • 4 Stars
    7
  • 3 Stars
    1
  • 2 Stars
    1
  • 1 Star
    0
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
  • 2
  • 3
Customer Repair Stories
 Average Repair Rating: 2.9 / 5.0, 139 reviews. What's this?
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Dryer squealed like a pig and at times the drum stopped rotating
First thought the problem was a stretched drum belt or bad idler pulley. Ordered a new belt and idler assy plus spring. Replaced those items with relative ease following suggestions obtained at this site.However, problem persisted and I now suspected a bad drum bearing. Odered the bearing kit and replaced same using the following procedure.
1. Removed the cover from the back of the dryer (held in place via two phillip head screws)
2. Pushed down on the idler assy and removed the idler spring to release the drum belt.
3. Inserted flat tip screwdriver between the top panel and the dryer main body in the front of the dryer to pry the top loose from the two retaining clips.
4. used phillips screwdriver to remove the two retaining screws (one left, one right) that hold the front panel to the main body of the dryer. (about a foot down from the top of the dryer).
5. disconnected the wiring plug on the top right hand side at the top of the dryer.
6. lifted the front panel slightly removing it from the main body and placed it to the side.
7. lifted the rear of the drum to release it from the bearing bracket and removed the drum belt.
8. Pulled the drum through the front of the dryer body and moved it to an open work area.
9. Reached into the Dryer and loosened the two
bearing bracket screws with a nut driver. Here's where another pair of hands would have come in handy. Holding the ground bar on the back of the drum with on hand, reached into the dryer and finished removing the bracket screws somehow managing not to drop the tiny grounding ball (size of a BB) Removed the badly damaged plastic bracket, grounding bar, and grounding ball and set
them aside to be discarded later.
10. Used impact driver with phillips attachment to remove two of the three screws that hold the bearing to the back of the drum (these are on the inside) The third screw's head stripped out and I had a very difficult time removing it. Had it not been for that, the job would have taken less than an hour.
11. I had my wife hold the bearing in place while I started the three retaining screws.
12. My wife also got behing the dryer and held the grounding bar in place while I installed the new bearing bracket . (this kept me from loosing the grounding ball)
I just reversed the rest of the procedures to install the drum belt, drum, front panel, etc.
The dryer works like new now, doesn't squeal.
Also replaced the on/off switch knob (just pulled the old one from the stem and slid the new one on.
Other Parts Used:
Selector Knob
  • charles from new holland, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
689 of 706 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
squeeking like crazy
well, i started at the top and worked my way down. by taking the top off, it gave me more room to get the dryer tub out. took the two screw`s out of the vented plate on the back of the machine to undo the belt. this is a stackable washer-dryer combo, so next i took off the white plate on front between washer & dryer. took off the control panel, unpluged it, then took dryer door front off. then removed the two screw`s that hold that bracket on ,in the back of dryer, pulled the drum out & replaced the belt, but before replacing anything i took the shopvac to it , there was alot of lint in there.when replacing the Grounding Ball Clip & Grounding Ball, i took a one inch by two inch magnet and used it to hold the Grounding Ball & Clip in place so i could get the two screws started in the Drum Support Bearing & Bearing Bracket. after installing that i put the shaft in place & lined the dryer tub up with the 3 screw hole`s ,and boom, bang, pow...nothing to it. it`s easy...parts came very fast....Thx PartsSelect.com...i`ve told all my friend`s about PartsSelect
Other Parts Used:
Multi-Rib Drum Belt Drum Support Bearing Dryer Drum Bearing Bracket
  • Steve from Wheelersburg, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Wrench set
393 of 456 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Other Parts Used:
  • Frank from Boyertown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
332 of 348 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clothes got caught , burned and ripped on front of drum
I felt ,if I was going to replace the top drum glide and lower basket seal, I might as well replace the belt ,bearing assembly and the idle pulley assembly and avoid having to replace these sooner than later. All of the parts showed alot of wear and the belt like all drive belts, should be changed every 5-6 years.
DISCONNECT ELECTRICITY and GAS LINES
1.popped top by pushing and prying at front /top clips about 2-3in. in from side edges. lifted it off
2. removed the front panel by removing the 2 top front screws from the inside, then the two lower screws from the front after removing the small white plastic hole covers. disconnected the multiplug electric connector top right. set panel aside.
3.remove small back panel.and loosened belt.(observe belt path and idle pulley assy.
4. lifted drum and slid it out the front.
5. using socket, removed rear plastic bearing housing and replaced the same. be careful of observing the small ball bearing and the small piece on outside back panel. replace the same. you wil probably need a second set of hands to hold the piece on the outside when screwing in the screws from the inside.
6. unscew the "bearing" from the rear of the drum and replace with new one.(the screws are self-tapping and go in HARD!!)
7. apply lubricant liberally to plastic bearing holder
8. place new belt around drum(rubber side against drum cloth side out.
9. idle pulley assy. is removed by removing spring and just sliding assy out of holder. replace with new
10. replace drum and belt
11. take front panel and remove top drum glide and lower basket seal.( i marked where the two seal/glide come together with a marker )
12. scrape and remove as much felt and possible. I then used "goo gone" to remove all the glue. clean well and using the provided high temp adhesive reattached glide and seal.
13. reassemble and enjoy your NEW? dryer
Other Parts Used:
Drum Belt Upper Drum Glide Front Lower Drum Seal Idler Arm Assembly Idler Arm Spring
  • john from owego, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set, Wrench set
160 of 238 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer squealed loudly
First, I removed the top panel which is held on at the front by pressure clips. Second, I removed the entire front panel which entailed removing 2 screws and 2 wire couplings. Third, I removed the 3 screws on the inside center of the drum which turned out to be unnecessary. Fourth, I slid the drum forward in order to access the rear bearing. Lastly, I replaced the entire bearing assembly including the shaft, bracket, bearing, grounding ball and clip. Again, probably not needed but I had ordered the parts in advance in preparation for the worst.
Other Parts Used:
Drum Support Bearing Dryer Drum Bearing Bracket SCREW
  • Glenn from Fort Worth, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
99 of 129 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
rear support bearing squeeking
removed top and front of machine. removed drum. replaced shaft, bearing bracket, and support bearing from inside. replaced grrounding ball and clip from outside. reassemble.
this should be available as a kit, and should include high temp grease to put in bearing bracket
Other Parts Used:
Drum Support Bearing Dryer Drum Bearing Bracket
  • Paul from Mont Pelier, VT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
96 of 2058 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
retainer around drum dryer was wore, back bearing squeeks
I look up on the internet on how to disassemble dryer to get to the parts needed. Took off top, found screws to take off front. Removed existing drum riding seal and lower seal. Used laquer thinner to remove excess glue. Cleaned throughly with soap and water. Reapplied new seals.

At the same time removed drum and parts in the back of the dryer for ball bearing. great, expeditious help from your store. Thank you
Other Parts Used:
Upper Drum Glide Front Lower Drum Seal Drum Support Bearing
  • Timothy from Manlius, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
90 of 2578 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer making squeeking sounds and clothes getting caught in drum causing brown spots
I followed others suggestions with numbered steps and listened to others suggestions about replacing other parts while in the dryer. I took the dryer apart and cleaned it out well. I used acetone to remove the glue from the felt and Drum Glide at the top of the Drum. It worked much better than Goo Gone. By doing the clean up and evaluation one day, I ordered all the parts that I saw were worn or difficult to get to. I replaced the Heating Element only because the old one was very brittle and to get to it again would be difficult. Also, I followed other's advice to photograph the parts before removing. It was easy to remember how things went if I had a photo to refer to.

When the parts arrived it only took about 30 minutes to install them all because the glue removal, lint removal, and parts removal had been done another day. I should add that I am a 66 year old woman and found the job quite simple. Excellent web site. Thanks to others for the step-by-step instructions. Oh, to hold the Drum Glide and felt in place while the glue cured, clothes pins work great. I let the glue cure overnight to make sure that it was really secure.
Other Parts Used:
Drum Belt Upper Drum Glide High Temperature Lubricant Front Lower Drum Seal Drum Support Bearing Heating Element Assembly
  • Ann from Blanco, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
75 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had 2-seperate problems; 1st was a high pitch squeel, 2nd was the cover overheating
The high pitch squeel was the result of a failing drum bearing. It was particularly evident when first turning on the dryer, but became softer as the dryer heated up. In order to replace the drum bearing, I removed the top panel and front door panel.

The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.

The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.

From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.

Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.

The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.

I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.

I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.

Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.

After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.

THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base
Other Parts Used:
Blower Housing with Blower Wheel
  • Gerald from Cumming, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
73 of 95 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bearing and heating element broke
Had to first remove the top of the dryer this was done by removing the clamps on the back. Next I removed the front of the dryer by removing the two nuts the frong in the inside, these are somewhat hard to reach. Next the drum was removed. then the heating element shield. Replaced, the heating element then secured it into place. replaced the drum bearing assembly, and put back together.
Other Parts Used:
Heating Element Restring Coil with 1/4" Terminals
  • Kevin A Frech from Sidney, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
65 of 91 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

29 questions answered by our experts.
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Seamus
July 20, 2017
I cannot seem to detach the drum to install my drum bearings. Do you have any tips or tricks?
PartSelect logo
Hi Seamus, if you are having troubles detaching the drum we suggest lifting it from the back to lift it out of the cup, and remove it. I hope this helps!

31 people found this helpful.

Was this helpful?
Thank you for voting!
Katie
July 20, 2017
I think I am installing the rear drum bearings incorrectly because they keep failing prematurely. Is there something different I should be doing? Is there another part I should be checking that could affect the performance of the bearings? Thanks
PartSelect logo
Hello Katie, the most common reason for this happening is a restricted or overly long dryer ducting. If there is too much heat and not enough air flow it will cause a blow back into the cabinet, which would greatly affect your bearings. This is also harmful to other mechanical and electrical features in your dryer. We recommend inspecting your dryer ducting before replacing the drum bearings again. Best of luck with this repair!

20 people found this helpful.

Was this helpful?
Thank you for voting!
Beth
July 20, 2017
I’m replacing the drum bearings but I also need to replace the felt seal (front). Do you have any advice on how to do this?
PartSelect logo
Hello Beth, to replace the felt seal you will need to remove the top panel and the mounting screws on the back. After that the control panel assembly should come off. Then the front panel of the dryer can be removed. From here you can install the new felt seal 134440200 (which can be glued down). To get to the bearings you will need to remove the belt, then the tub can be lifted out of the front of the unit. From there you can change the bearings. Please let us know if you have any further questions.

16 people found this helpful.

Was this helpful?
Thank you for voting!
Manny
November 4, 2017
I order a rear drum bearing kit about two years ago its going bad again is this normal or should it last longer?The drum glide is this one piece or do I need upper and lower.
For model number GLGR642AS5
PartSelect logo
Hi Manny, Thank you for the question.Normally the bearing will last longer. I suggest making sure the appliance is level and The appliance requires 2 and they are sold individually. Hope this helps!

10 people found this helpful.

Was this helpful?
Thank you for voting!
Carlos
January 28, 2018
Hello, I replaced the rear drum kit. The loud squeaking stopped, but the noise has now been replaced with a loud robust sound. I took the drum out and tried resetting it. What should I check now?
PartSelect logo
Hello Carlos, Thanks for your question. Without the dryer model number we can only give general information, but you may wish to also check the drive belt, the drum roller axles, the blower wheel, drum glides, and the idley pulleys for any signs of wear and tear. If all else fails, it could be the drive motor. I hope this helps.

7 people found this helpful.

Was this helpful?
Thank you for voting!
Jerry Jasso
March 28, 2018
Do you all sale rear drum bearing kit for my dryer.
For model number Kenmore 417.97812701
PartSelect logo
Hello Jerry, thank you for your question. The rear drum bearing kit for your model is part number 5303281153. Please enter the part number into the site for current price and availability. Good luck with your repair!

7 people found this helpful.

Was this helpful?
Thank you for voting!
Jennifer
November 13, 2018
Hello, My Frigidaire dryer gler341as2 started making a thumping noise with each rotation. will replacing the rear drum bearing fix this? are there any other parts that i need to replace? i replaced the dryer drum belt 2 years ago and the drum glides 8 months ago, in case that helps. thank you! jennifer
For model number Frigidaire gler341as2
PartSelect logo
Hello Jennifer, Thank you for the question. We would recommend replacing the Rear Drum Bearing Kit Part Number: PS459829. Sounds like an issue with the small ball bearing and clip or the support, both come with this kit. Hope this helps, good luck with this repair!

7 people found this helpful.

Was this helpful?
Thank you for voting!
Fred
October 5, 2017
My dryer makes a low-pitch rumbling sound -- not the high-pitch screech -- and the exhaust of air seems to pulse. Is a bad rear drum bearing likely to be my problem? Thanks.
For model number 4178204101
PartSelect logo
Hi Fred, Thank you for your inquiry. There are some parts that you will need to check to see which one is causing the issue. You will need to check the rear drum bearing kit, the drum support bearing, the drum belt, the drum glide, the front lower drum seal, the bearing bracket, and the ball hitch. I hope this helps. Thank you and have a great day!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Trevor
July 9, 2019
Hi what is the white plastic piece that appears to attach to the interior of the dryer connecting to the barrel and front at the top
For model number GLER341AS2
PartSelect logo
Hello Trevor, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS5574052 Drum Glide. Please note: these are sold individually, however there are two of these in your appliance. We recommend that these be replaced at the same time, this allows for optimal performance and ensures they wear evenly. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Stephen
January 9, 2019
Front of drum dropped down clothes are getting ruined. What could be the problem ? I can push up on the front of the drum.
For model number FSE747GES1
PartSelect logo
Hello Stephen, Thank you for the question. I suggest checking the support for the rear bearing, Part Number: PS418807 and other parts of the Read Drum Bearing kit, Part Number: PS459829, If they are wore or or damaged, it will cause the drum to fall or to be loose. Thank you for your inquiry, good luck with this repair!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
  • 2
  • 3
;
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS459829
Manufacturer Part Number: 5303281153
Brand
Model Number
Description
Frigidaire
41749012890
Dryer - Residential, Electric
Frigidaire
41749022890
Dryer - Residential, Electric
Kenmore
41759012890
Dryer - Kemore Dryer 41759012890
Frigidaire
41759022890
Dryer - Gas
Kenmore
41761712510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41761722510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41761722511
Washer Dryer Combo - Laundry Center
Kenmore
41761723510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41761723511
Washer Dryer Combo - Laundry Center
Kenmore
41761732810
Washer Dryer Combo - Laundry Center
Kenmore
41761732811
Washer Dryer Combo - Laundry Center
Kenmore
41761733810
Washer Dryer Combo - Laundry Center
Kenmore
41764182300
Dryer
Kenmore
41769042990
Dryer
Kenmore
41769042991
Dryer
Kenmore
41769052990
Dryer
Kenmore
41769052991
Dryer
Kenmore
41771712510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771712511
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771712512
Washer Dryer Combo - Laundry Center
Kenmore
41771722510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771722511
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771722512
Washer Dryer Combo - Laundry Center
Kenmore
41771723510
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771723511
Washer Dryer Combo - LAUNDRY CENTER
Kenmore
41771723512
Washer Dryer Combo - Laundry Center
Kenmore
41771732810
Washer Dryer Combo - Laundry Center
Kenmore
41771733810
Washer Dryer Combo - Laundry Center
Kenmore
41771733811
Washer Dryer Combo - Laundry Center
Kenmore
41774182300
Dryer
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service