Part Location Diagram of 5303279394 Frigidaire Tub Seal Assembly
See part 26 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Tub Seal Assembly

★★★★★
★★★★★
5 Reviews
$100.53
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS459481
Manufacturer Part Number 5303279394
Manufactured by Frigidaire
Product Description

Tub Seal Assembly Specifications

This seal helps prevent any leaking around the transmission of washing machines.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Westinghouse, Gibson.
Part# 5303279394 replaces these:
AP2142342, 461, 5308027482, N8027481, N8027482, NF141842-100, NF141842-200, NF14184210, NF14184220
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
5 Reviews
5.0
Filter By Rating:
  • 5 Stars
    5
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.5 / 5.0, 7 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
The primary problem was that the tub seal assembly was leaking.
1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.

2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.

3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.

4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.

5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.

6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.

The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy.
Other Parts Used:
Tension Idler Pulley TRUNNION FILTER
  • Rick from Walkerton, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
253 of 318 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noisy spin cycle
1) Unplugged washer and disconnected the hot and cold hoses.
2) removed the 2 phillips screws at the bottom of the front panel then removed front panel, you need enough clearance by the floor, this is tricky because you have to lean washer back and push down on the front panel.
3) removed the agitator from the washer
4) lifted top of washer and leaned back against the wall and removed the splash tub cover one clip at a time with a flat screw driver.
5) removed the trunion, this is difficult and will take some time due to the corrosion from many years of use use a hammer (3Lb short handle) and tap one side then the other. You will need to rock it back and forth awhile.
6) lift the basket out of splash tub
7) I removed the hose for water level and removed the 3 bolts that hold the splash tub to the three base mounts (support arms).
8) remove the splash tub
9)change the plastic washer that is between the splash tub and the transmission in the bottom of the splash tub
10) change the bearing(metal sleeve) on the bottom of splash tub and lightly grease w/ a thin film of teflon grease
11) install splash tub and install the 3 bolts along w/ the water level tube
12) install the larger seal (w/ spring in it) and push into the splash tub firmly
13) use some tub and faucet silicone grease on the smaller seal because you don't want to damage this main seal, install the main seal (sits on top of the larger one that's in the tub already) be careful when getting to flat part of the shaft when installing ( spin around the shaft as you pass this point) it will keep the seal from coming out.
14) install trunion (sits down on top of the seal) you will feel the tension of the spring when bolting the trunion back into place.
15) install basket and bolt it to the trunion (I installed a new filter on the bottom of the basket and required some special glue, ask for "3M" GMGA600 adhesive.
16) installed splash tub cover, agitator and front cover.
Washer works great and is quieter than it was new.
Other Parts Used:
Upper Spin Bearing Washer Spin Bearing Outer Tub Upper Outer Tub Cover FILTER
  • Patrick from Humble, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set
137 of 162 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bearing and seal at top of transmission went bad causing oil from transmission to stain clothes
I removed front and top of washer to get acess to the tub. removed cap to tub along with inner tub and agitator. the hardest part is removing the springs on the bottom and tilt it forward to get tub out. removed belt, pulley and bolts holding transmission in place. reassemble using silicone grease on seals and washers. works great now
Other Parts Used:
Transmission Assembly Agitator Drive Block
  • dave from port sanilac, MI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
56 of 84 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer not spinning, water leaking out bottom
My first step was to download and print out the parts diagrams from the manufacturer's website. With a basic idea of what I needed to get to I first removed the agitator cap and the agitator and right off I found a broken bolt on plate lock bracket that holds trunnion which supports and connects the tub to the transmission drive shaft. I replaced the bolt and put it back together and gave it a test run. Spun very nicely now but water was going everywhere. Unfortunately I found that when the bolt broke the tub had slipped down and ripped the rubber "tub seal assembly". To get to the seal I ended up tearing the machine completely down and removing the whole motor and transmission assembly out of the unit. It may be possible to get at the seal without doing this but I'm not 100% sure. To get the whole unit apart I did the following: Remove the front panel by removing the two screws located at the very bottom of the panel and lifting up and out .Remove the top/lid by removing two screws underneath the top toward the front, and disconnecting lid switch, or i found it easier to just unscrew and remove it, then lift off the top/lid assembly. Remove the agitator cap and the agitator. Remove the splash cover (this is not easy- I popped each tab with a flat screw driver- the ones at the rear were very difficult). I tried to remove the fill spigot but could not get at one of the screws so getting the splash cover out was not as easy as it could have been. Remove the bolts in the bottom of the tub and lift it out. Unhook the drain hose and the level or "pressure tube". Remove the 3 large and 3 small springs from the motor assembly ( I needed a strong spring hook but all I had was vice grips, they work but it was not easy). remove any other wires etc. (mark things with tape and matching numbers if needed) and pull out the whole barrel and motor assembly. Unbolt the splash tub and remove, unbolt the trunnion and remove. And finally replace the seal. Reassemble in reverse order. Important!! Clean shaft well (I used some 300 grit fine sandpaper to remove the little bit of rust scale that had accumulated) and lubricate everything. be very careful when reassembling, as to not scuff up the seals at all. I used a silicone spray. This might not be the best thing for the job but I know at least not to use anything petroleum based such as WD-40 when you are lubricating rubber or plastic. Reinstalling the springs was very difficult and again a spring hook would have been great. Everything else went together reasonably easy. The unit works fine now. many thanks to the websites I researched to get this done.
Other Parts Used:
  • Michael from Springfield, VT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
29 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Tub was leeking
Lifted top
removed adgetator
removed tub top
removed inside tub
removed inside tub holder bracket
repaced seal
replaced,replaced.....
Other Parts Used:
  • Gregory from Fort Worth, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
13 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water from machine
This repair is realy very easy
As discribed by the others
Other Parts Used:
  • Martinus from Fort Lauderdale, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set, Wrench set
10 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking through the main tub seal
-Remove front panel - 2 screws
-Remove the top panel - 2 screws
-Disconnect the lid switch from the top panel - 2 screws
-Remove the agitator cap - unscrew
-Remove the agitator - This was a bit difficult and required a lot of jiggling but it eventually came off
-Remove the inner drum - 5 bolts at the bottom
-Remove the drum mount - 2 bolts and then it got really difficult. A lot of penetrating blaster, wire brushing, jiggling, and some strategically placed hammer taps (don't damage the threads.
-Remove the seal
-Clean up the inner and outer seal seating surfaces
-Rinse and repeat in reverse (pun intended)
Other Parts Used:
  • Rob from DACULA, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

8 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Phillip
August 27, 2017
How do i remove the washer tub from a Westinghouse washer dryer combo
For model number MLXE42REW0
PartSelect logo
Hi Phillip, Thank you for your inquiry. First, disconnect the power and the water from your appliance. You will have to remove the end caps from the right and left side of your control panel to give yourself access to the screws holding your control panel in place. Once you unscrew those you will be able to flip your control panel back to reveal the retaining clips. Disconnect the lid switch wiring. Using a flat head screw driver, unclip the retaining clips from your machine. Then, lift the lid, grab the inside of your machine and lift the whole body off of the rest of the cabinet at a 45 degree angle. Use your foot to brace the bottom. Once you have that out of the way, remove the hose from the vacuum break. Then to remove the vacuum break you will have to flex the tabs and then pull out gently from the bottom so that you can pull down to release the rest of the tab. After that you will remove your agitator. Remove your fabric dispenser and you will see a bolt at the bottom of your agitator. unscrew that bolt and you will be able to remove the agitator. After that, use a spanner wrench to remove your spanner nut. To remove the tub cover, press down above the tabs that are around your tub and then gently pull off the tabs. Be careful to not be to rough. Once you have that cover off you will be able to remove your tub. Good luck with your repair.

3 people found this helpful.

Was this helpful?
Thank you for voting!
Bill
February 9, 2020
How to replace tub seal assembly
For model number MWX111REW0
PartSelect logo
Hello Bill, Thank you for your question. We suggest to take pictures of each step to make sure they are assembled back together. Remove the front panel by removing the two screws attached at the bottom. Remove the lid by removing the two screws underneath the lid toward the front. Remove the agitator cap and the rest of the agitator, then remove the splash cover by popping out each tab with a flat head screwdriver. Then remove the bolts at the bottom of the tub, and lift out the tub. Unhook the drain hose and the pressure tube, then remove the springs from the motor assembly, and any other wires attached. After pulling out the barrel and motor assembly, unbolt the splash tub and the trunnion, then you should be able to replace the seal. Make sure before reassembling the machine to lube everything so the seal is not scuffed up or damaged using a simple silicone spray. We hope this helps.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Dave
September 4, 2019
Hi, my combo washer/dryer is leaving drops of oil underneath the washer. Do you know how to fix it? Replacing the tub seal assembly seems to only fix water leaks. Thank you! Dave
For model number GLGT1031FS0
PartSelect logo
Hello Dave, Thank you for the question. If the appliance is leaking oil it is coming form the Transmission and it will need to be replaced. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Paul
November 2, 2017
How to replace tub bearing.
For model number 417.44142400
PartSelect logo
Hi Paul, Unfortunately we do not have instructions on how to replace that bearing as your tub bearing is not sold separately from your rear outer tub. Thank you for contacting us.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Shirley
October 8, 2017
I can see what looks like metal shavings from location of where transmission goes down to shaft with belt
For model number GLWS1979AS2
PartSelect logo
Hi Shirley, Thank you for your question. You may have to replace your transmission or have a technician come and take a look at your appliance. Good luck with you repair.

Was this helpful?
Thank you for voting!
Jerry
November 2, 2017
It is a Kenmore laundry center made by Frigidaire company. I need the seal at the top of the transmission. I believe the number is 4,5,and 27. Can you help me. Sears don't sell the parts.
For model number 417.93862200
PartSelect logo
Hello, Thank you for contacting us. Checking your model number the seals you are asking for are only sold as part of the Transmission.Hope this helps!

Was this helpful?
Thank you for voting!
Glen
March 13, 2019
Will this part work with my Frigidaire Electrolux commercial heavy duty washer /dryer combo
For model number GLET1031CSO
PartSelect logo
Hello Glen, thank you for your question. Yes, Tub Seal Assembly PS459481 is compatible to model GLET1031CS0.

Was this helpful?
Thank you for voting!
Veronica
August 1, 2019
I have a washer and dryer combo, Frigidare. The washer drains the water but does not want to spinning. It makes the noise as if it were spinning, but it does not.
For model number FLSE72GCSA
PartSelect logo
Hi Veronica, Thank you for your question. If the washer is draining, but not spinning, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door lock with external safety switch, the belt, the motor and the pump. I hope this helps. Thank you and have a great day!

Was this helpful?
Thank you for voting!
  • 1
;
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS459481
Manufacturer Part Number: 5303279394
Brand
Model Number
Description
Kenmore
41790802990
Washer Dryer Combo
Kenmore
41790802991
Washer Dryer Combo
Kenmore
41790802992
Washer Dryer Combo
Kenmore
41790807990
Washer Dryer Combo
Kenmore
41790812990
Washer Dryer Combo
Kenmore
41790812991
Washer Dryer Combo
Kenmore
41790812992
Washer Dryer Combo
Kenmore
41790814000
Washer Dryer Combo
Kenmore
41790814001
Washer Dryer Combo
Kenmore
41790814002
Washer Dryer Combo
Kenmore
41790817990
Washer Dryer Combo
Kenmore
41790862990
Washer Dryer Combo
Kenmore
41790862991
Washer Dryer Combo
Kenmore
41790862992
Washer Dryer Combo
Kenmore
41790872990
Washer Dryer Combo
Kenmore
41790872991
Washer Dryer Combo
Kenmore
41790872992
Washer Dryer Combo
Kenmore
41791702000
Washer Dryer Combo
Kenmore
41791702001
Washer Dryer Combo
Kenmore
41792702200
Washer Dryer Combo
Kenmore
41793702200
Washer Dryer Combo
Kenmore
41793702201
Washer Dryer Combo
Kenmore
41793802200
Washer Dryer Combo
Kenmore
41793802201
Washer Dryer Combo
Kenmore
41793812200
Washer Dryer Combo
Kenmore
41793812201
Washer Dryer Combo
Kenmore
41793814200
Washer Dryer Combo
Kenmore
41793814201
Washer Dryer Combo
Kenmore
41793862200
Washer Dryer Combo
Kenmore
41793862201
Washer Dryer Combo
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service