Heater Coil with 5/16 Inch Terminals Specifications
Coil only.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Gibson, Tappan, Kelvinator.
Part# 5300622034 replaces these:
AP2135128, 351, 5300622034
Customer Reviews
Average Rating:
★★★★★
★★★★★
8 Reviews
5.0
Filter By Rating:
5 Stars
8
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Jean-Philippe G - December 11, 2020
Verified Purchase
Perfect fit
Fast shipping, great packaging, genuine part, easy to install.
★★★★★
★★★★★
Denise M - October 11, 2020
Verified Purchase
I love my dryer is back to normal
Thank you soo much my dryer is drying my clothes again in 40 minutes instead of not drying at all
★★★★★
★★★★★
Dany R - July 28, 2020
Verified Purchase
Easy repair...
The part was in great condition and came fast. My dryer is back in working order! The instructions was usefull to replace the heater coil.
★★★★★
★★★★★
Petro P - February 29, 2020
Verified Purchase
Easy repair - worked as expected
The part was in grearr condition and came fast
★★★★★
★★★★★
Morgan S - September 27, 2019
Verified Purchase
dryer is working again
The part was the correct part and fit well. It was delivered on time and was cheaper than some other sites. It was fairly easy to find the part considering that the paperwork we kept didn't have a list of part numbers. Seeing the picture helped a lot. I helped my husband put the dryer back together in about one and a half hours.
★★★★★
★★★★★
Darren H - May 8, 2019
Verified Purchase
Worked as expected
I live in Alberta but the parts came from Nova Scotia.
★★★★★
★★★★★
Marten B - April 1, 2019
Verified Purchase
perfect
exactly as described, brand new, instructions for installation were bang on, had dryer working in no time. very grateful dryer has returned to life!
★★★★★
★★★★★
Norman P - August 22, 2018
Verified Purchase
Easy shopping
Great, as expected. Thanks
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.3 / 5.0, 5 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Dryer would not heat
First..kudos to PartSelect for their fantastic support! Great work folks.
While greasing the bearing in the back of the drum, I found my heating coil was broken. Steps to replace:
1) Unplug the unit 2) Remove the top panel. Note, do not remove the center front screw that does not go into the door. 3) Remove front outer panel 4) Remove interior front panel 5) Remove front control panel 6 screws, pushing downward the panel and disconnecting connection to door. 6) Remove door by removing the screws on the top and pull door straight off. (I left the air duct attached to the door) 7) Remove the back access panel to the motor 8) Release the belt from the idler pulley and remove the belt. 9) I removed the three screws in the center of the drum as I found it difficult to remove the drum from the bearing. Remove the drum. 10) disconnect the coil terminals by first bending the tabs outward to allow you to be able to pull them off the block 11) remove the old coil 12) carefully stretch the new coil so that it measures 48 inches (no more) 13) Plug new coil into terminals and bend tabs to lock in place. 14) Divide heater coil in half and install coil onto center support on the opposite side from where it connects to the block/back wall of dryer 15) Install remaining coils onto supports. 16) reinstall all parts in reverse order.
Other Parts Used:
Mark from Normalville, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
107 of 126 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No Heat From Dryer
Repair requires nearly complete dis-assembly of the cabinet.Starting with the steel panel directly below the control panel, remove 2 screws. Next, remove the screws on the lower corners of the control panel. The control panel can drop down now and be removed from the cabinet. The door frame must be removed next. Start by disconnecting the door interlock connector from the wiring harness and then removing the screws on the top of the cabinet that hold the frame. remove the frame. The dryer tub is next and is removed by extracting the three screws in the back of the tub that bolt it to the bearing. The tub is now free and is pulled out of the front of the cabinet. Now comes the challenging part. The actual bearing is a sphere that is held in place by a spring loaded socket. The bearing must be removed in order to access and heater assembly. The bearing is removed by pushing it with considerable force upward toward the top of the cabinet. This strong force is necessary in order to overcome the force of the springs that hold the ball bearing in in place. I found removal of this bearing perplexing because no mention is mentioned anywhere of the amount of upward force that it takes to remove it and I was afraid of breaking it by forcing it. Now the heater assembly can be easily removed and replaced. This whole process is challenging and time consuming. At the same time you can feel a degree of satisfaction when you are done.
Other Parts Used:
C. William from Milford, NY
Difficulty Level:
Difficult
Total Repair Time:
More than 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable)
29 of 32 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drum turns but no heat
Frigidaire / electrolux stack washer dryer Removed door panel,top,control panel not sure all needed to be removed except door then removed 3 screws in center at rear of drum this disconnects the drum to shaft that secures it in place ( could not find info on that step and is the reason for writing this hope it helps , reassemble in reverse
Other Parts Used:
Reed from Seatac, WA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
20 of 28 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced heater coil and thermal limiter switch
Followed the excellent instructions for the heater coil. There weren’t any for the TL switch as to which of the two TL terminals gets power. Took a guess, reassembled the dryer (many hours) and it worked. I was either lucky, or it didn’t matter. Wish it had come with specific installation instructions.
Other Parts Used:
Chuck from STERLING, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No heat, element bad
With the excellent replacement parts sold by this site, it went like silk. The dryer is not only working great, but actually quieter.
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Leeann
July 12, 2019
My heating element coil is broke. Do I have to replace the whole element; or can I just replace the coil?
For model number FER641FS0
Hello Leeann, Thank you for the question. You can replace just the Coil, PartSelect Number PS451032. Thank you for your inquiry, good luck with this repair!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Binh
February 8, 2022
Is this an OEM Coil?
For model number FDE336RES2
Hello Binh, Thank you for your inquiry. All of the parts we sell are OEM parts direct from the manufacturer and have a 1 year warranty. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Chuck
December 27, 2023
Which heating element coil will fit my Frigidaire dryer?
For model number FEQ332CES0
Hi Chuck, thank you for reaching out. The compatible heating element coil for your model is part number PS451032. We hope that helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS451032
Manufacturer Part Number: 5300622034