
Tension Idler Pulley
$25.43
Special Order



Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
PartSelect Number PS418897
Manufacturer Part Number 131862900
Manufactured by
Frigidaire
Product Description
Tension Idler Pulley Specifications
This idler arm assembly comes with the pulley wheel.

How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Burning smell | Will not agitate | Spins slowly
This part works with the following products:
Washer, Washer Dryer Combo.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Westinghouse.
Part# 131862900 replaces these:
AP2107757, 780774, 131312800, 131825500, 3204422, 5303311337
Customer Reviews
Filter By Rating:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Ted R - November 20, 2019

Easy Repair
Back in working order.
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The primary problem was that the tub seal assembly was leaking.
1. I began by removing the two screws that hold the front panel in place. I then lifted the top free of the front panel and tilted it back to get it out of the way.
2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.
3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.
4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.
5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.
6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.
The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy.
2. Using my fingers, I released the tabs that connect the tub cover to the tub. It took some effort to remove the cap("Mechanism") over the bolt connecting the agitator to the agitator drive block because I didn't want to break the tab. Once removed, I removed the bolt and the agitator. I then removed the two bolts that clamp the Trunnion to the agitator shaft.
3. It took a little more effort to remove the tub because of corrosion, however, by rocking the tub back and forth I was able to work it free and remove it. I then removed the bolts connecting the Trunnion to the tub. It took a hammer to remove the Trunnion from the tub, once again because of corrosion.
4. After removing the tub, the seal assembly was next and it was easy to remove. I cleaned the agitator shaft with steel wool before beginning the reassembly to remove the corrosion. Before installing the new seal, I lubricated the agitator shaft and the inside of the seal with a silicone grease that is normally used for water faucets. The seal installed easily although care was required to insure that the seal did not twist out of place when sliding it down the agitator shaft.
5. The rest of the reassembly went easily. Since my old filter on the bottom of the tub was clogged, I replaced it with a new one. It took a little time to get every tab on the filter aligned properly so that it could be rotated into place, but it went easily. Everything else reassembled with no problems.
6. It took considerable time to figure out how to replace the drive belt idler arm assembly because I could not figure out how to remove the pin that the idler arm pivots on. I finally reviewed the parts list on-line again and determined that there is a small C-clip that holds it together. Once I knew that. I was able to see the clip and remove it. From that point on, it was very easy to remove the old assembly and reinstall the new one. If I had to do it over again, I would have changed the sleeve at the same time that I changed the idler assembly because the assembly still wobbles on the pin more than I would like. However, it works fine so I won't worry about it until other repairs are needed.
The parts that I ordered from Parts Select were exact matches for the parts that I removed. They were in stock and were shipped the next business day. I would rate the repair as very easy.
Other Parts Used:
-
Rick from Walkerton, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
253 of 317 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nicole
April 2, 2018
When the clothes are done with the first wash and, they being to spin out the dirty water. The washer makes a squeaking sound for a couple of seconds, then the noise stops. When the washer is in the rinse cycle it doesn't make the squeaking noise. I changed the belt and i'm still having the same problem. Please help
For model number CWS3600AS0

Hello Nicole, thank you for your question today. I would suggest replacing the Tension Idler Pulley 131862900 and the PULLEY Part Number: 131498301. These parts work with the belt, and since the belt was replaced the noise is probably coming from one of those parts. I hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Christopher
April 5, 2019
It wont spin unless I start it by hand. What is it?
For model number CRWS5700AS0

Hello Christopher, thank you for contacting us. For this symptom you will want to replace either the Drive V-Belt part PS1146950 or the Tension Idler Pulley part PS418897. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Zach
July 12, 2021
Might this be the culprit of my squeaky top-loader? I've been trying to tune in to a squeak taking place as the washer's drum is agitating. I hear a high pitched squeak each time the drum rotates ccw while agitating. The noise is even more prominent during the 'normal' wash cycle versus 'gentle'. It also randomly occurs as the drum slows down from the spin cycle. I have replaced the drive belt, although the original was showing no real signs of failure. While doing so, I inspected and lubricated/greased all mating components. I was unable to recreate the noise with manual movements. On the surface, the original tension idler pulley appears to be in fair condition. Unless I were to operate the washer without its front panel, I cannot precisely detect where the squeak is coming from. Thank you for any assistance you may be able to provide!
For model number GLWS1749AS4

Hello Zach, Thank you for the question. We suggest checking for wear to the Tub Seal Assembly, Spin Bearing, Pulley and the Trunnion. we hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
Cheryl
January 30, 2023
My machine only makes noise when the spin cycle is stopping - like a car squealing it's brakes.
For model number FWX833AS1

Hi Cheryl, thank you for contacting us. We recommend checking the following parts: the spin bearing, part number PS446536, the drive v-belt, part number PS1146950, and the tension idler pulley, part number PS418897. If these parts do not solve your issue, the transmission assembly, part number PS1524603, is probably defective. Please reach out to customer service if you need help placing an order. Glad to be of help!
Was this helpful?
Thank you for voting!
Related Parts:
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS418897
Manufacturer Part Number: 131862900
Manufacturer Part Number: 131862900
Brand
Model Number
Description
