This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. The main reason you would replace this screw is if the old screw is missing or damaged. This part is sold individually and is an OEM part sourced directly from the manufacturer.
Average Repair Rating: 3.3 / 5.0, 6 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Drying too slowly
Removed access plate from back bottom left Removed belt from motor Needed to lift up top of dryer Inserted flathead screwdirver in front under top to push in two metal clips holding top down Lifted up top of dryer Removed 2 screws holding on front of dryer Removed front of dryer Broke Door Switch removing front of dryer. I should have depressed the metal sides in and pulled switch through hole. Instead, I tried to remove the leads. This broke the fragile prongs. Started dryer (with belt removed so drum doesn't spin) Verified ignightor came on every heating cycle Gas turned on properly Gas turned off after 90 seconds Gas never came back on Indicitive of bad coils New coils solved the problem Replaced door switch and lint trap cover in the process.
Inserted new vane into slots in the drum. I then held the front of the drum while I slid the vane tabs in place by pushing the vane to the back of the drum. Once the vane was in place, I screwed in the screw that came inside the vane kit.
I googled and found parts select, listed model make and found parts diagram, found suspected parts from trouble shooting blog. I read repair stories, people who performed identical repairs, followed their lead, made notes ordered parts and easily repaired my dryer for a fraction of the cost of replacing dryer.
I took off the front of the dryer where the felt liner was located. Took off the old glide and scraped off the old glue with the razor blade. Took the tube of glue from the package and put glue where the old was and pressed the new felt on the dryer front. I then put it together and waited till morning to do a load of clothes. It works fine.
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sherry
January 2, 2018
Can you please tell me what size this screw is?
For model number GLTF1670AS0
Hi Sherry,
Thank you for your question. The screw is approximately half an inch. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Lawrence
January 12, 2018
What is the screw threads size
For model number PS417463
Hi Lawrence, Thank you for the question. Very sorry but we do not have the thread size.This is the screw that screws in from outside of the drum into the vane/baffle. Hope this helps!
Was this helpful?
Thank you for voting!
Sue
April 8, 2019
The cage that you put the lint filter in is missing a screw on one side, I am not sure what number is after the es, I took the number off the invoice
For model number agq6000es
Hello Sue, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS417463. Thank you for your inquiry, good luck with this repair!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
