This is a replacement mullion rail for your French door-style refrigerator. You will typically find the mullion rail on the left side refrigerator door. The mullion rail helps to keep the refrigerator door closed. If the door will not close properly or if you notice leaking on your floor, you may need to replace the door mullion. A faulty mullion can gather moisture, resulting in a leak. To replace the mullion, simply disconnect the old mullion from the wire harness and unscrew it. Re-attach the wire harness to the mullion and screw it back into place.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Kristina D - December 27, 2023
Verified Purchase
Worked great
This part came quickly and was really easy to install. Way cheaper than buying a new fridge!
★★★★★
★★★★★
Mark H - November 24, 2023
Verified Purchase
Exact fit
Less than 5 minute to install ,and the part has been updated , so it will not fail like original
★★★★★
★★★★★
Christine C - June 15, 2023
Verified Purchase
Very easy repair
This part arrived really fast and I was able to replace the broken piece in 5 minutes. This flapper fit the older model of fridge I have and is a better quality and designed piece. I have confidence that this part will not wear out and break like the original flapper did.
★★★★★
★★★★★
Anson L - June 1, 2023
Verified Purchase
Easy to replace and install. Works as expected.
The part came in great condition and is easy to install. It’s a super important part as it keeps the fridge sealed properly.
★★★★★
★★★★★
Terry M - March 1, 2023
Verified Purchase
Flipper Plate
Part fitted perfectly. Very easy to install. Took about 5 minutes. Very pleased with this product.
★★★★★
★★★★★
Paul J - August 14, 2022
Verified Purchase
Arrived quick. Worked perfectly.
Perfect fit, upgraded from the original design where the spring failed. Quick, easy, saved money. Couldn't be happier.
★★★★★
★★★★★
MIKE B - April 20, 2022
Verified Purchase
Easy repair, done in minutes.
It wasn't difficult to replace this part. Just a few screws and easily lifted away. Installation was no trouble at all.
★★★★★
★★★★★
Harvey H - March 20, 2022
Verified Purchase
Great part
Worked well.
★★★★★
★★★★★
André T - October 30, 2021
Verified Purchase
Easy ton change 5 minutes
Perfect easy ton instal fit on perfect
★★★★★
★★★★★
Mathieu G - October 1, 2021
Verified Purchase
Easy install
Not exactly like original part but does the same job.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 17 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
My nephew accidentally forced the door closed last year, which resulted in the door having to be re closed manually folding back the flap. Ugh!
Unscered 2 screws, unplug electrical connection under the screws, slide her flap into grooves, realign screw holes , and rescrew in. Done.
Other Parts Used:
Tiziana from WARWICK, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
23 of 36 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken Door Mullion Spring
Had to buy the entire door mullion because the spring broke, wasn't happy. Got the new part very quickly and it was a new replacement part number. Somewhat tentative. Took it out of the box and looked it over. No spring! Groan! Thought I got the wrong part. Flipped the bottom hinge and it snapped open, no need for a spring! Two screws, disconnect the wire harness, throw away the old, get new, connect the wire harness, connect hinges, put in two screws! Super easy. Watch the video for some pointers along the way.
Other Parts Used:
Maurice from SEATTLE, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
13 of 17 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken spring door million torn door gasket
Door million undid 2 screws in plug wire easy no need for directions. Gasket pull off old one fit New in with index finger no tools needed.
Watched a YouTube video on how to replace the door flipper (mullion). Very easy to unscrew the plate and disconnect the electrical circuit. Then gently slide up the flipper and replace with a new one.
Other Parts Used:
Patrick from AUGUSTA, WV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plate Assembly Spring Broken
Remove 2 screws holding to door. Slide assembly up. Unplug connector. Remove old Plate Assembly. Do reverse to reinstall. Plug connector. Push in wires. Slide plate on. Fasten screws. Done
Other Parts Used:
Jim from WELLINGTON, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front Plate Assembly Not Closing Properly
Found the part on Parts Select. Ordered the part, which came quickly. While waiting for delivery. I watched a short video on how to replace this part. I'm a 73 yr. old female, and no trouble at all. I really felt a sense of accomplishment. Thank you Parts Select.
Other Parts Used:
Brenda from WEATHERFORD, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring on old mullion fell out
Replaced with new mullion
Other Parts Used:
MIKE from ATLANTA, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The spring on the mullion door broke for the last time
This was an incredibly easy repair! 1 phillips screwdriver and two screws. Disconnect the small adapter, and you are good to go!
Other Parts Used:
Sonya from VAIL, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spring broke on Mullion
Watched the video. Took the screws out, unplugged the connection and slid mullion off. Then plugged the new one in, slid it on and attached the two screws.
Other Parts Used:
Michael from MONTGOMERY, AL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Mullion (flapper) - spring broke
The spring broke on the flapper (mullion) on my refrigerator. I sent a chat message to PartsSelect (they answered right away) to see if they had a replacement spring but it was not available so had to order the whole mullion. They gave me the part # I would have to order. It arrived quickly. The new mullion didn’t have a visible spring but it worked the same if not better. I just had to remove 2 screws on the center plate on the existing mullion, pull the plate out enough so you will be able to slide the mullion (the wires are under the plate kind of like the ones you see on a ceiling smoke detector) but you can’t get under the plate until you release the mullion. Push up on the mullion so that the plastic tabs on the top and bottom are released. Once the mullion is released (you have to hold it), you’ll see the wires. Unhook the wire part by just pushing down on the little tab and remove it. To install the new one, just reverse the steps. Align the top and bottom plastic tabs to fit into the slots, just enough to hold it in place. If the plastic tabs are not already flipped out, you’ll have to just flip them out. The top tab does not have tension but the bottom tab has tension so just push on it with your finger to flip it out. The plate covering the electrical is a rather tight fit and you have to make sure the little tab on the inside of the plate is above and behind the tab on the inside where the wires are so it slides behind it so you can get it in position before sliding the mullion back down into place and the electrical plate is in place too. Then screw the 2 screws back in. The hardest part is holding the mullion while un-attaching the electrical and just make sure you stuff the wires in enough so you can get the plate back in position. I’m a 75 yr old woman and managed fine by myself. At first when installing the new one, I couldn’t slide the mullion down enough to get the electrical plate in position and then realized I had to have the little tab inside the electrical plate behind the tab inside the wire compartment so they didn’t hit one another when pushing the mullion back down. Then, all went fine.
Other Parts Used:
Sonia from CALIF CITY, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
12 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sandra
November 21, 2021
Is the mullion flap suppose to open or stay flat when the door is closed? We installed a new one and the flap stays flat against the mullion. Thought it would have opened to seal the opening between the two doors.
For model number LFX25978st/00
Hello Sandra, thank you for writing. We have researched the model you have provided and have found a video for PS12374439. The video shows exact positioning for you. We hope to hear from you soon.
11 people found this helpful.
Was this helpful?
Thank you for voting!
Butch
July 20, 2021
What is the dimensions of the door latch.
For model number 7951033010
Hello Butch, Thank you for the question. The Front Plate is about 37" Long. We hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
James
October 14, 2021
The photo looks like this part has a gray colored front surface. Is there a version in white?
For model number LFX25978SW/00
Hello James, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11708993 for the White Flipper Assembly. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Vivian
October 16, 2021
Do you know if this mullion will fit this 2 door, bottom freezer model with manufacturing date of 2013?
For model number 795.71033
Hello Vivian, Thank you for your inquiry. We have researched the partial model number you have provided and as there are two versions beginning with this model number, we show two different part numbers for the mullion. This mullion will fit model number 79571033010, and for model 79571033110 the part number for the mullion assembly is PS11708993. We do not receive the manufacturing dates from the manufacturer, so we would advise checking for the complete model number or checking with the serial number for the date. We hope this helps.
Left door plate assembly does not spring into place to allow for hands free door closure
For model number LFC25765ST
Hello Mark, thank you for writing. You have chosen the correct part for your model LFC25765ST. The Front Plate Assembly is PartSelect Number PS12374439. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mark
May 5, 2022
Looking to replace the door flapper. Can you confirm the correct part number?
For model number LG lfc25765sw /00
Hi Mark,
Thank you for your question. The part number listed under your model number for the door flipper assembly is PS11708993. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dale
October 23, 2023
What is the part number for the door mullion for this model with stainless exterior
For model number LFX25778
Hello Dale, Thank you for your inquiry. Researching your model, we confirm that PS12374439 is the compatible stainless door mullion. We hope this helps
1 person found this helpful.
Was this helpful?
Thank you for voting!
Martie
January 31, 2024
Is the wire harness in the door mullion replaceable or do I need to buy the entire door flap?
For model number LFX25974ST
Hi Martie, thank you for reaching out. The wire harness in the flipper assembly does not come separately. You may need to order the complete flipper assembly, part number PS12374439. If you need help placing an order, customer service is open 7 days a week!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ken
August 12, 2022
The spring that provides the auto return on the flap broke. Unfortunately, a simple spring replacement does not appear to be offered anymore. Do I need the Plate or Flipper assembly?
For model number LFX25978SW /00
Hello Ken, thank you for writing. There is the Flipper in White as part PS11708993 or the Flipper in Stainless Steel color as part PS12374439. You are correct in that the spring is not sold separately. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
Hello Jarrod, thank you for contacting us. The compatible flipper mullion for your model in black color is part number PS9865158. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you!
