Maytag/Maytag_Thumb/LTB0UTYQ.gif
See part 4 in the diagram
Replacing your Whirlpool Dishwasher Thermal Fuse and Harness play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.ca

Thermal Fuse and Harness

★★★★★
★★★★★
13 Reviews
$44.59   In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

 Fits your 66513599K600!
 Fits your 66513599K600!
PartSelect Number PS382828
Manufacturer Part Number 675813
Manufactured by Whirlpool
Product Description

Thermal Fuse and Harness Specifications

*Please Note - When changing the fuse always use a new wiring harness.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Not draining
This part works with the following products:
Dishwasher.
This part works with the following products:
Whirlpool, Kenmore, Estate, Maytag.
Part# 675813 replaces these:
AP3115186, 679723, 3375557, 3376359, 675813
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

6 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dan
November 18, 2017
When we push any button the light comes on for that selection, but when we the push start button it will not start the dishwasher. Any suggestions?
For model number 66515762000
Hello Dan, The thermal fuse and harness should be tested with a multimeter for continuity and replaced if it is not showing continuity, as that is the most common reason for the dishwasher not starting. It is also worth testing the door switch (part number PS358749) for continuity and replacing it if it is not showing continuity, as that can prevent the dishwasher from starting as well. Only if the prior two parts are testing for continuity should consider replacing the electronic control board itself, part number PS11746115. I hope this helps.

7 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Mary Beth
December 12, 2017
Replaced the fuse and it worked and finished cycle. The second wash it stopped again. Got another fuse and it worked for half of the cycle. What would cause a thermal fuse to continue to blow?
For model number DU945PWPQ0
Hi Mary Beth, Thank you for the question. When changing the fuse always use a new wiring harness.If the harness is not changed it will blow the fuse again. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Richard
September 29, 2017
Kenmore dishwasher......select option on control panel....push on button....immediately shuts off panel. is this the thermal fuse problem? or control panel?
For model number 66515822000
Hi Richard, Thank you for the question. In this case I suggest replacing the Electronic Control Board,PartSelect Number PS11746115. The thermal fuse would need to be replaced if the appliance worked but had no display. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
David
January 18, 2018
The only lights that come on are cancel, and heavy and normal. The heavy and normal come on at times and blink when i press and hold cancel for a few seconds. Then when i press cancel again they all go off. I press normal then both normal and heavy come on and stay lit (doesn't happen when just heavy is pressed). When i press start the lights go off. Press and hold cancel and heavy and normal start blinking, and when i let go they all stay lit. Press start and the cancel button stays lit and the heavy and normal turn off. Then hold cancel and the heavy and normal start blinking again, as in the second sentence. I replaced the main control board with a new one and get the exact same sequence of events.
For model number DU945PWSQ0
Hello David, Thank you for your inquiry. If you've already replaced the main control board, I would check the control panel and touchpad assembly. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jim
May 13, 2019
Unit shows lights on control panel push button for normal wash hear click to start but won't.Check thermal fuse it is black on top blown,can fuse just blow or possible thermostat cause this, so i should replace that also
For model number DU940QWDQ6
Hello Jim, Thank you for the question. We suggest replacing both parts at the same time. Normally if one blows it is an indication there is a issue with the other. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Mary
December 8, 2017
My husband replaced fuse a few months ago. It quick working again and now replaced a fuse and it worked for one load but second load it stopped before dispensing detergent. Water not drained. He didn’t replace the electrical that came with it. Could that be the problem?
For model number DU945PWPQO
Hello Mary, Thank you for the question. Yes, the electrical should also be replaced for proper operation of the fuse. Good luck with the repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Part Videos

Replacing your Whirlpool Dishwasher Thermal Fuse and Harness

Replacing your Whirlpool Dishwasher Thermal Fuse and Harness play video
Customer Repair Stories
 Average Repair Rating: 4.2 / 5.0, 4 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Touch pad on dishwasher dead
1. Remove the two screws that attach the bottom cover.
2. Remove the 2 screws that attach the door outer cover.
3. Remove the 8 screws that attache the door inner cover.
4. Remove the plastic cover over the electronic controller.
5. Remove the two connections to the thermal fuse.
6. Remove the thermal fuse.
7. Install the new thermal fuse.
Reverse the above steps.
Other Parts Used:
  • Jeff from Boaz, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
113 of 132 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No power to dishwasher.
Unplug the dishwasher. Simply removed 8 screws on the inside of the door, removed the interior door panel. Next popped of the plastic protective electrical panel cover. Locate the Thermal fuse that had simple instructions provided. Removed the fuse and replaced the harness. Put everything back together. Plugged dishwasher back into electrical outlet...Dishwasher resumed with the cycle that the dishwasher was in when the fuse blew. Simple, Fast AND Reliable!!!
Other Parts Used:
  • Brad from Woodbury, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
36 of 43 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher did not completed the drying cicle. heated dry button blinking
I just changed all parts that could make any effect in temperature control. even the thermal fuse. this was easy,looking in details all the drawings you have in your page. so I pulled out the dishwasher changed the parts and ready!! it work great now . thanks for your guide and help.
Other Parts Used:
Electronic Control Board Cycling Thermostat Kit High Limit Thermostat
  • Eduardo Figuera from miami, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
36 of 78 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The machine just quit in the middle of a cycle and there were no lights on the control panel
There were eight of the star head screws to remove to take the front off the dishwasher, then just followed the instructions that came with the part, which was a thermal fuse and the new wiring that accompanied the fuse in the order. The hardest part was getting the old wire out of the harness with the other three, but once I figured that out just slid the new wire into place and made the connections. I reinserted the screws, turned the power on and knock on wood shes still working.
Other Parts Used:
  • Ronald from Garland, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
30 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
13 Reviews
5.0
Filter By Rating:
  • 5 Stars
    13
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS382828
Manufacturer Part Number: 675813
Brand
Model Number
Description
Kenmore
66513402K900
Dishwasher
Kenmore
66513402K901
Dishwasher
Kenmore
66513409K900
Dishwasher
Kenmore
66513409K901
Dishwasher
Kenmore
66513442K900
Dishwasher
Kenmore
66513442K901
Dishwasher
Kenmore
66513443K900
Dishwasher
Kenmore
66513443K901
Dishwasher
Kenmore
66513444K900
Dishwasher
Kenmore
66513444K901
Dishwasher
Kenmore
66513449K900
Dishwasher
Kenmore
66513449K901
Dishwasher
Kenmore
66513492K600
Dishwasher
Kenmore
66513499K600
Dishwasher
Kenmore
66513592K600
Dishwasher
Kenmore
66513593K600
Dishwasher
Kenmore
66513594K600
Dishwasher
Kenmore
66513599K600
Dishwasher
Kenmore
66513692K600
Dishwasher
Kenmore
66513699K600
Dishwasher
Kenmore
66515632000
Dishwasher
Kenmore
66515634000
Dishwasher
Kenmore
66515637000
Dishwasher
Kenmore
66515639000
Dishwasher
Kenmore
66515652000
Dishwasher
Kenmore
66515654000
Dishwasher
Kenmore
66515659000
Dishwasher
Kenmore
66515682000
Dishwasher
Kenmore
66515684000
Dishwasher
Kenmore
66515689000
Dishwasher

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service