Part Location Diagram of W10410997 Whirlpool Drive Motor - 115V
See part 015 in the diagram
Replacing your Maytag Dryer Drive Motor - 115V
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Drive Motor - 115V

★★★★★
★★★★★
4 Reviews
$207.15
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS3500892
Manufacturer Part Number W10410997
Manufactured by Whirlpool
Product Description

Drive Motor - 115V Specifications

This part has a D-shaped motor shaft and this motor runs at 1/4 horsepower and carries 4.5 amps.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Maytag Dryer Drive Motor - 115V

Replacing your Maytag Dryer Drive Motor - 115V
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer, Washer Dryer Combo.
This part works with the following products:
Maytag, International.
Part# W10410997 replaces these:
AP5272723, 2118675, W10410997, 33001753, 33001853, 33001854, 33002237, 33002462, 33002478, W10410997VP, WFR181207
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
4 Reviews
5.0
Filter By Rating:
  • 5 Stars
    4
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.6 / 5.0, 21 reviews. What's this?
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Motor buzzed and dryer drum would not spin when pressing start
From the first time the motor buzzed (but dryer tumbler then started to turn), 2 weeks elapsed for the dryer drum to stop turning altogether. If this occurs, DO NOT continue to push the start button because the motor armature wiring will heat up and the insulation will begin to melt and smell - a SAFETY HAZARD. Unplug dryer and lockout/tagout as appropriate.

Through basic troubleshooting, discovered the motor had seized up. Since the unit was about 10 years old and it had to be disassembled for replacement, the decision was made to replace "likely to fail mechanical components including motor, belt, both rear drum rollers/shafts, idler arm pulley/assembly/wheel, associated washers, snap rings and both front glides. Reviewed the PartSelect website and drawings, ordered the parts and they delivered on time. Buy the correct sized snap rings at a local hardware, they're much less expensive. Also once inside your dryer, you'll likely find alot of lint to vacuum out...have fun.

I went online and Googled several resources that showed how to remove the front dryer panels, as well as PartSelect repair stories. From that point on, I took photos as I was disassembling so I would know how to put it back together. Utilize pictures or whatever system you prefer to keep track of taking something apart and putting it back together.

Remove the dryer door, then the front panel Disconnect wires to the light, dryness sensor and door switch. Note belt and pulley configuration that is near the motor-this will help you later when reinstalling the belt. Also note if the ribbed side or the flat side of the belt is against the outer drum wall. Remove the door shroud.

Slip the belt off the idler pulley wheel. Remove front drum support, then dryer drum Note which end of the dryer drum is the front and the orientation of the glides on the drum support. Discard old belt. Drill out and remove the old front glide supports, then install/rivet the new glides.

Remove both old rear drum rollers/shafts, washers, etc. The rear drum roller shafts are secured to a back bracket by a hex nut....feel around you'll figure it out. Replace new roller shafts. Lightly grease using a high quality silicon grease, then replace new washers, roller, snap ring, etc

Carefully unplug wiring harness on motor, there are fragile clips on each end. Don't forget a separate ground wire from the harness is attached to the motor mount bracket. Carefully release tension on the idler arm spring. Using the correct size nut driver, remove three screws (on this model) then take out the motor/idler arm assembly. Remove the old idler arm/pulley assembly. Remove the motor mount clips on each end of the mount (I used a wide blade screwdriver). Remove and replace the motor. Motor configurations changed after Whirlpool bought Maytag, so orient it correctly insuring mounting gasket "nubs" on each end of the motor correspond to the cutouts on the motor mount. Reinstall the motor mount clips. Replace the new idler arm assembly/pulley wheel; grease moving parts with high quality wheel bearing grease. Replace motor/mount bracket assembly back into the dryer. Replace ground wire to motor mount bracket and plug wiring harness back in. Reinstall idler arm spring.

Place belt back on the dryer drum and move into place on rear rollers. Reinstall front drum support. Dryer drum should turn relatively easy. Insure belt is oriented on the drum correctly before connecting belt to motor shaft end and idler arm wheel pulley (the picture you took comes in handy here).

Reinstall the rest of the parts in reverse.
Other Parts Used:
Idler Arm and Shaft Idler Pulley Wheel and Bearing Roller Shaft Idler Pulley Shaft Washer Multi Rib Belt - 91-5/8 Inches Drum Roller Shaft Washer Front Glide Kit Drum Support Roller Kit
  • Frederick W. from Austin, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench set
198 of 280 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Over the last year the 'start' button has had to be held to 'start' the dryer, with a humming noise during the process. Eventually it hummed, stank, and wounldn't start.
Yanked the front panel, observed motor operation while my smoking hot wife started the unit. Our washer and dryer get beaten like rented mules with kid laundry. I tried this site, and decided to spend a little $$ on a replacement motor. I was impressed with the operator, she even asked what the symptoms were and helped to avoid wasting time and money.
The part arrived on time, and installed quickly. I am a hero in my wife's eyes, and that certainly carries weight.
Then again, I didn't have to dispose of the old dryer, pay for a new one, or haul the replacement upstairs.
Win-win!
Other Parts Used:
  • Ryan from Raleigh, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The dryer drum would not rotate when the start button was pushed.
First this I did was to disconnect the power cord. Then I removed the screws that held on the door and the two on the other opposite side. This allowed the front panel to be removed. Next I removed the top two screws which allowed the top to hinge up and out of the way. Then I removed the rest of the screws that held the front drum support and moved it to the side. I did have to unclip the wires that ran to the interior light. I did not how ever have to disconnect any wires at the front of the dryer. Next I reached in from the bottom of the drum and released the drive belt from the spring loaded pulley. at this point the drum was able to be removed out the front of the unit. This gave access to the motor. It was necessary to remove the several screws that held on the front half of the fan housing. Again I did not remove any wires as this too could be moved to the side out of the way. I then removed the snap ring and clamp from the fan end of the motor shaft and pulled the fan off of the shaft. Next I unclipped the wiring connector from the top of the motor and used a screw driver to pry the connector off. Next I used a socket on a long extension to push down on the motor clamps while tilting the socket out to allow the clips to release. I then removed and replaced the motor and assembled in the reverse order. While I had the drum out I inspected the rear support wheels and noted that one would hardly turn. I removed both wheels via a nut on the back side of the shafts. I found that one had shifted on the bushing and was making contact with the frame. I used a vise to press the wheel back into the correct location. I also applied anti seize with a small amount of dry graphite to both wheels and insured that the both rotated freely. I then installed the front two glide slide pads using the pop rivets provided in the kits. I used a shop vac and cleaned any lint from inside the dryer. I then reassembled the front covers in reverse of the disassembly process. I rotated the drum by hand prior to applying power. I also ran the unit with the heat off for the first five minutes. Total cost was under $160.00 or half of the replacement cost.
Other Parts Used:
Front Glide Kit
  • Bruce from Gladstone, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor burnt a phase
If you are cursed with owning a Maytag product then you'll be glad PartSelet.com is in business. I get all my parts here.

My dryer motor burnt a phase. The tear down was very straight forward since there isn't much to a dryer. I did the tear down in the driveway. The dryer was full of lint so I blasted it with compressed air to clean it up. Keep all your parts in labeled baggies as you do the tear down. Reassembly goes much faster. The hardest part about changing the motor was getting the motor clips off. They are tough buggers. I used slip-joint pliers & finally popped them off. This job is simply enough for the average monkey. Just use the diagrams on partselect.com if you forget where something goes.

I shipped everything via fedex 2-day. It took 5 days to get here. partselect shipped it fast. fedex was the problem. I guess the boys at fedex have a public education is they think 5=2.
Other Parts Used:
Multi Rib Belt - 91-5/8 Inches Dryer Drum Felt Seal Drum Support Roller Kit
  • Jim from Bellevue, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blower wheel had broken fins, motor bearings loose
This was fun! Kill the power!
Remove door, remove from panel, remove front drum support, remove drum and belt, remove blower cover, remove blower wheel, remove electrical connector from motor, take two clips off motor mount to remove motor. Put it all back in with new parts. 200 bucks and back in business. Go for it.
Bob
Other Parts Used:
Blower Wheel
  • Robert from Lebanon, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
5 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would not run
Removed door and front and drum. Removed fan assembly. Be careful when working fan off of motor shaft. Unhooked wiring from motor. Removed clips. Replaced motor. Reverse procedure to put dryer back together. Now works like new. Very, very, happy. Part came in 2 days using standard shipping. Way better than buying a new dryer.
Other Parts Used:
  • Beverly from Oakland, MD
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer made a buzzing sound when start button pushed. Would not start.
Took off front. Removed door. Removed drum support. Removed drum and belt. Made sure motor was correct size and fit. Removed blower wheel. Disconnected wire plug from motor and slid motor out of blower wheel. Replaced everything in reverse order. Figuring out belt tensioning position was a trip, but finally got it. Vacuumed out all the lint. Amazingly it worked!
Other Parts Used:
Multi Rib Belt - 91-5/8 Inches
  • Joe from Nashville, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Socket set
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
motor hummed but wouldn't turn drum
Unplugged dryer and removed screws that hold door in place. removed screws that hold front panel. removed front panel. took drum belt off idler pulley. pulled drum out of dryer cabinet. unhooked wiring harness and removed motor. replaced motor and reversed steps to put back together. Thanks to partselect for getting me the parts so quickly. I ordered the motor on line on Friday and it was at my house on Saturday.
Other Parts Used:
  • Yvonna from Mulberry Grove, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers, Wrench set
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer motor went bad
Unplugged the dryer (don't forget this step guys!!!)

Pulled the front off the dryer (4 screws) and swapped the motor out - take off the belt, pull the blower wheel (by removing the snaprigs and squeeze collar), then pull off the motor retaining clips... unplug the motor and install the new one in reverse. Took me less than 2 hours and my dryer works like new.

WAY CHEAPER than a new dryer!!!
Other Parts Used:
  • Sandy from Brookshare, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldn't start
My Husband did the repair. He had to take the entire dryer apart to get to the motor. Removed door, front pannel, drum. During this repair he also replaced the belt since it had cracks and since the dryer was taken apart. placed new motor in and put all back to gether many screws he had to remember where they all went. Have to be very careful with the felt liner around drum. we started dryer has never ran more smoothly. Two people recommended to put dryer back together.
Other Parts Used:
  • Heather from Charlevoix, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

5 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Leroy
December 16, 2017
On the back of the motor is a pulley that is grooved. I believe it is to keep the belt tracking on the drum. Can this part be replaced without buying another motor? Where can I buy the part? Instructions for replacing the part?
PartSelect logo
Hello Leroy, Thanks for your question. The pulley is only included with the motor itself. You will need to disassemble most of the dryer to install the part, but we have a video on the part page itself with exact steps on doing so. I hope this helps.

5 people found this helpful.

Was this helpful?
Thank you for voting!
Cath
November 8, 2019
Need new motor. Online search indicates part no: W10410997 but told by another company that I need w10197708. Are they interchangeable? Which part do I need to order?
For model number MDE16CSAGW
PartSelect logo
Hello Cath, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Manufacturer Part Number W10410997. I am not showing the w10197708 is a compatible motor for this appliance model number. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Gery
January 2, 2018
Serial number 75859812cr of dryer. P/n on motor 63719070. Current motor will not turn without use of a wrench. You have several motors displayed, all saying they fit my dryer with different numbers and prices. Which one fits my dryer?
For model number MLE2000AYW
PartSelect logo
Hello Gery, Thank you for your inquiry. Part# W10410997 is the drive motor for the dryer. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Nadarajah
September 3, 2021
Buzz sound when pushed start button. Suggested replace motor What is the correct part number for this model
For model number WED4851EW
PartSelect logo
Hello Nadarajah, thank you for writing. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS334304. A buzzing or whining noise while the dryer runs is a good example of when the motor is the issue. We hope this helps.

Was this helpful?
Thank you for voting!
Related Parts:
Dave
June 12, 2023
My dryer does not list a series number, and I can’t find a serial number look up. What motor do I need for serial number :28673917wz
For model number Mde4000azw
PartSelect logo
Hi Dave, thank you for the question. The drive motor, part number PS3500892, that you have mentioned is compatible with your model and serial number. We hope this helps!

Was this helpful?
Thank you for voting!
  • 1
;
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS3500892
Manufacturer Part Number: W10410997
Brand
Model Number
Description
Maytag
MDB9206AWW
Dryer - Maytag Dryer Model MDB9206AWW Parts
Maytag
MDE14PDACL
Dryer - Electric
Maytag
MDE14PDACQ
Dryer - Electric
Maytag
MDE14PDACW
Dryer - Electric
Maytag
MDE14PDADL
Dryer - Electric
Maytag
MDE14PDADW
Dryer - Electric
Maytag
MDE14PDAGW
Dryer - Electric
Maytag
MDE14PNAYW
Dryer - Gas
Maytag
MDE14PNAZW
Dryer - Gas
Maytag
MDE14PRAYW
Dryer - Gas
Maytag
MDE16CSAGW
Dryer - Electric
Maytag
MDE16CSAYA
Dryer - Electric
Maytag
MDE16CSAYQ
Dryer - Commercial
Maytag
MDE16CSAYW
Dryer - Electric
Maytag
MDE16CSAZA
Dryer - Electric
Maytag
MDE16CSAZQ
Dryer - Commercial
Maytag
MDE16CSAZW
Dryer - Commercial
Maytag
MDE16MNAGW
Dryer - Electric
Maytag
MDE16MNAYW
Dryer - Electric
Maytag
MDE16MNAZW
Dryer - Electric
Maytag
MDE16PDAGW
Dryer - Commercial
Maytag
MDE16PDAUW
Dryer - Commercial
Maytag
MDE16PDAYA
Dryer - Commercial
Maytag
MDE16PDAYQ
Dryer - Commercial
Maytag
MDE16PDAYW
Dryer - Commercial
Maytag
MDE16PDCZW
Dryer - Electric
Maytag
MDE16PRAGW
Dryer - Residential
Maytag
MDE16PRAYW
Dryer - Residential
Maytag
MDE16PRAZW
Dryer - Residential
Maytag
MDE16PSAZW
Dryer - Gas
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service