NOTE: This part has been updated by the manufacturer. With this control the wiring could be different from the original. It will possibly need to be installed by an appliance repair person.
Average Repair Rating: 4.1 / 5.0, 6 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Yje electronic control panel was shorted out. I orderd a new one and in a timely mannor your service delivered the part via Fed Ex.
The repair was simple. All wires were color coded and the new part had the same color codes marked. Simply unplugged the wires from the bad part and plugged them into the new part a reinstalled the part to the back panel of the range.
Other Parts Used:
Gary from Wichita, KS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
28 of 36 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
blew out board by crossing wires..mistakenly toke out bulb assembly to replace bad bulb
Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..
Other Parts Used:
Ken from CALABASH, NC
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven could not be turned off once settings were turned on except by unplugging hookup.
Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.
Other Parts Used:
Charles from BENNETTSVILLE, SC
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not get come up to temperature
I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair actions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!
Other Parts Used:
Arthur from INDIANAPOLIS, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My electronic control board went out so I could not use my oven. My oven light blew as well.
I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right spots on the new control board and put it back together.
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Other Parts Used:
Ryan from COHOES, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
12 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
James
October 21, 2017
I have a code popping up f7-22. Does that mean a board or something else
For model number jbs55dom2ww
Hello James, thank you for contacting us. That error does indicate an issue with the control board. You would need to replace it. Good luck with the repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Rebecca
November 5, 2017
Neither element will heat, but i have no error message. Do i need a new control panel or new elements?
For model number JBS55SM8SS
Hi Rebecca,
Thank you for contacting us. I would suggest testing both your broil and bake elements. You should also test your temperature sensor as well to make sure that part is still working. If all of those parts are checking out to be fine, then it may be your control board that is the issue. You can test all of your inner over parts with a multi meter to make sure that it is not one of those that is giving you the trouble. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Patrick
September 17, 2019
I was cleaning stuff out of the back by the control panel 2 leads touched because one was not fully connected. Anyway, my burners work, the 2 red indicator lights work, however my oven is dead and my light display is dead. Work this be more than the control panel to replace?
For model number J BS55S M2SS
Hello Patrick, thank you for your question. It sounds like the control board shorted out, or fried. You would want to replace Part #: PS3491492 Electronic control board. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Steve
December 28, 2017
Bad line error code and beeping
For model number JBS55DM2BB
Hi Steve, Thank you for the question. The Bad Line error could be a few things. There could be a loose or bad wire or voltage spikes or surge in the outlet the appliance is plugged into. I suggest unplugging the appliance and resetting the outlet at the breaker. Plug the appliance back in to see if the error clears. You can also check the wiring to the electrical plug and the control board. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Tiffany
January 13, 2018
The control panel that works the start push button keeps burning and smoking when using only the oven. Do i need a new control board?
Hi Tiffany,
Thank you for your question. It sounds like yes you would need a new board. You may also need to check your touchpad as well. I hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Stan
February 24, 2018
The bake part of my oven does not heat up. My heating element popped and was replaced.The broiler part works fine. You hear the click when you turn on bake but no heat. Any ideas?
For model number jbs55dm2ww
Hello Stan,
Thanks for your question. You may wish to test the temperature sensor and the bake element with a multimeter to see if they have electrical continuity. Replace them if they do not have continuity.
I hope this helps.
My clock displays only partial digits, and my up button to adjust time/temp is hard to work. Would replacing this part help?
For model number JBS55DM2WW
Hi Torey, Thank you for the question. This sounds like an issue with the Control Board, PartSelect Number: PS3491492. It is not repairable so it will need to be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
TIMOTHY
May 5, 2018
My range was working fine one morning but then by the evening all of my burners and oven went out. The clock and indicator lights on the control board work. Replace the circuit breaker and still no burners or oven. What's wrong? Thanks!
For model number JBS66MM2BS
Hi Timothy,
Thank you for your question. If your stove is not working, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the temperature sensor, the bake element, the terminal block, the electronic control board, the oven light socket, the burner switches and surface burner elements. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Katrina
March 13, 2019
I need to get a integrated hot surface control for this electrical stove. I know that this model is no longer made can you please advise what part number I could use to replace this.
For model number JBS55WK3WW
Hello Katrina, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS3491492. Thank you for your inquiry, good luck with this repair!
Was this helpful?
Thank you for voting!
John Adams
September 3, 2019
My burners are working but the clock and stuff are not. Is that the electric control panel problem?
For model number JBS55D M5WW
Hello John, thank you for your question. The board is what controls the clock and other control panel functions. You will want to replace the board, Part #: PS3491492 and the overlay Part #: PS7320240. I hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
