NOTE: This part has been updated by the manufacture to include the wiring harness.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Kenmore Washer Dispenser and Water Inlet Valve
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Kenmore, Whirlpool, Maytag.
Part# W10372095 replaces these:
AP4980184, 1817425, 8577407, W10045100, W10059320
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
5 Stars
1
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Benoît B - December 26, 2018
Verified Purchase
Cette pièce a réglé le problème de bruit intense de la laveuse.
Livraison rapide!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
September 26, 2019
The washer will only fill on "dark colors" and "rinse and spin" settings. We mostly use "towels sheets" cycle. It won't fill on the settings at all... just an "lf". i dirty old houses on it but put new ones on now. should l replace inlet water valve?
For model number WTW6600SW1
Hello John, thank you for your question. If the unit isn't filling on any cycle then the valve should be replaced, or tested first, then replaced if it fails that test. If the unit is only filling properly on some cycles and not others the issue would probably be the interface board which has, unfortunately, been discontinued. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
John
September 26, 2019
To test a "water inlet valve" - can I unplug the connectors and measure the resistance with a multi meter? You guys are awesome!
For model number WTW6600SW1
Hi John,
Thank you for your question. Here is a link from our website that you may reference on how to test a water inlet valve with a multimeter, https://www.partselect.com/Refrigerator+test-water-valve+repair.htm. This information can normally be found under the Instant Repairman link on our website either at the top of our home page or at the bottom of our home page under Free Repair Help. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Paul Wurtz
November 16, 2017
Machine starts with initial fill, after about 10 minutes into cycle valve only hums and will not fill leading to an eventual lf error. Machine did get very wet when i had my sprinkler system blown out for the season. Sprinkler valve was not secure and a sudden force of pressure entered the line and blew off hose from supply line. Could there have been damage to electronic valve from excess pressure or would it be the main brain itself? Fill valve filters are clear and all electronics are dry.
For model number WTW6400SW2
Hi Paul,
Thank you for your inquiry. The dispenser and water inlet valve is just one of the parts you will need to check. You will also need to check the electronic machine and motor control board. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Michael
January 22, 2019
When you turn on machine the water goes in for about 6 seconds then stops then it sounds like it starts to drain is their a way i can bring up a code ?
For model number wtw6600sb2
Hello Michael, thank you for your question. We have manuals on our site under the model information that might offer some help in getting the unit into a diagnostic mode. Usually if the unit goes from fill to drain, or fills and drains at the same time there is an issue with the siphon break kit PartSelect Number PS334490, or the water pressure sensor which is part of machine control board PartSelect Number PS11749893. We would also recommend checking the pressure hose that runs to the tub for any kinks, or breaks. I hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
