Whirlpool 341241 - Multi Rib Belt - 92-1/4" | PartSelect.ca
Multi Rib Belt - 92-1/4" – Part Number: 341241
Multi Rib Belt - 92-1/4" – Part Number: 341241 Multi Rib Belt - 92-1/4" – Part Number: 341241 Multi Rib Belt - 92-1/4" – Part Number: 341241 https://partselectca.azureedge.net/Schematics/Maytag/UTGT4VNQ.gif

Multi Rib Belt - 92-1/4"

24 Reviews

Your Price

CAD$19.72

PartSelect Number PS346995
Manufacturer Part Number 341241
Manufactured by Whirlpool

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

This part works with the following brands: Kenmore, Whirlpool, KitchenAid, Norge, Roper, Maytag, Magic Chef, Crosley, Admiral, Estate, Amana, Inglis, Jenn-Air, Hoover.

This part works with the following products: Dryer.

This part fixes the following symptoms: Will not tumble | Noisy | Will Not Start | No heat or not enough heat

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part Photo
Description
Price
Availability
(1)
PartSelect: PS11743765
This part provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. This arm attaches to the idler pulley wheel.
$17.93
In Stock
(14)
PartSelect: PS373087
NOTE: This kit is for 29" wide dryers built in 1965 or later. Please verify model # before ordering as may not work for all models. This kit comes with one multi-rib belt, two drum support rollers, one idler pulley, fo...
$34.38
In Stock
Questions & Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 353 reviews What's this?
26-30 of 353
14 of 16 people found these instructions helpful
Parts Used:
  • Multi Rib Belt - 92-1/4"
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Customer:
Scott from Bayport, NY
Change dryer belt
I opened up the dryer as per the instructions I had received from PartSelect tech support. It was very easy to do. The only unexpected thing was that the original belt had snapped and in doing so the idler pulley was actually laying on the floor of the dryer's bottom. I had to figure out how it went, but that only took a minute and I popped it back into place. I held the drum by hand while pulling the dryer face away so it wouldn't fall and then I slipped the belt over the drum and quickly closed the front up again. I aligned the belt on the spot where the old one had been, pulled it through the idler pulley and over the motor and voila. Done. I closed up the dryer and was on to another "Honey Do" project within 20 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

13 of 14 people found these instructions helpful
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Customer:
Tim from Fremont, MI
How to un-screw the blower fan!
The dryer motor quit working. Learned, if you are changing one that is old, get the blower wheel fan too! I could not break mine loose from the motor shaft, and had to bust it off.

To un-screw the blower wheel fan from the motor shaft: from the front of the dryer, grab the plastic fan on the back of the motor with an adjustable wrench, and the motor shaft on the front of the motor with vice grips. Turn the motor shaft CLOCKWISE holding the fan still to un-screw the fan. If you have to remove the pulley, grab the shaft and turn the pulley COUNTERCLOCKWISE with a wrench.

Just make sure to pay attention to the orientation of the new motor in the instructions. If you match the old motor, it will not fit. It is all spelled out in the directions.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

17 of 27 people found these instructions helpful
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Socket set
Customer:
William from BURNET, TX
Dryer was getting hotter than blue-blazes, melted synthetics, damaged belt
Removed back of dryer, there were 3 screws on each side. There were two thermostats on the output vent and one thermostat on the heating element housing. Adjusted the temp settings on the thermostats per the instructions received with each thermostat (cross-refernece of original number required). Each thermostat had two screws and two wires. Terminals were coded "1" and "3," must get correct wires back in same place. The heating element thermostat required to splice new connector on one wire (per instructions enclosed with thermostat).. Easy as pie. BELT: Remove screws from lint screen housing, then pry up front of top of dryer and swing back (make sure you are next to the wall so it doesn't fall.) Remove the bottom front panel, remove the door tension springs, remove the two screws on the front of the front panel and remove the two top screws on the inside of the door panel (leave the door attached, but use tape to hold it shut so it doesn't hit you on the head) Careful of the door switch wire, carefully lean door up so it doesn't fall. The Drum will fall when front panel is removed, so have someone to help you hold it up. You do not have to remove the drum. With your frend holding the drum, go under and pull the tension spring roller back to slack up the belt and remove the belt from the tensioner and motor pulley. Remove belt from drum. Wrap new belt around drum (ribs down facing drum) and re-route belt around pulleys according to diagram in instructions (same way you pulled it off). I did it by myself, but I got konked in the head by the door, so be careful. Easy, but awkward. Watch for sharp sheetmetal edges.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 19 people found these instructions helpful
Parts Used:
  • Multi Rib Belt - 92-1/4"
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Customer:
thomas from bloomfield, NJ
The drum was not turning because a broken belt
I lifted the top of the dryer cabinet, like the hood of a car using a screwdriver to pry it open. I removed the two screws in the upper right corner of the cabinet front. I disconnected the safty switch on the front door. The front of the cabinet can then be removed by lifting up the front off the pins in the base. With the drum exposed you can place the belt on and thread it through the two pulleys on the motor. Consult the diagrams provided on the PartsSelect website for the proper positioning of the belt on the pulleys. After the belt is installed spin the drum by hand one turn to make sure that it is seated properly on the drum and pulleys. Reassemble the dryer in the reverve order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 10 people found these instructions helpful
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Wrench set
Customer:
Harry from Atco, NJ
Klunking noise and poor drying
The top was hard to figure out but I found that it pops off at the front with a flat screw driver. Be careful not to scratch the paint. I found that a rear drum roller was bad and the drum seals were deteriorated. I ordered a new belt, roller kit, front, and rear seals. This way I hoped I will not have to take it apart again. The seal were the hardest parts to replace. Make sure you look and remember how they were on before removing them. The directions were not to clear on the seals. The rest were good. It is much better to do it once. Take a picture if possible, it might come in handy as I took mine apart a week or so before the parts came in. I also cleaned out all of the accumulated lint buildup with a shop-vac, including the vent pipe, heater area, and front door. When I was done with this it worked like brand new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

26-30 of 353
Customer Reviews
Average Rating:
24 Reviews
4.9
out of 5
Filter By Rating:
  • 5 Stars
    21
  • 4 Stars
    3
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:

Model Cross Reference

Brand
Model Number
Description
Kenmore
10686294140
Dryer
Kenmore
10686294340
Dryer
Kenmore
10686294540
Dryer
Kenmore
10686294740
Dryer
Kenmore
10686294840
Dryer
Kenmore
110.6085299
Dryer - Kenmore Dryer Model 110.6085299 (1106085299, 110 6085299) Parts
Kenmore
110.7080299
Dryer - Kenmore Dryer Model 110.7080299 (1107080299, 110 7080299) Parts
Kenmore
110.765340284414694
Dryer - Kenmore Dryer Model 110.765340284414694 (110765340284414694, 110 765340284414694) Parts
Kenmore
110.76702690
Dryer - Kenmore Dryer Model 110.76702690 (11076702690, 110 76702690) Parts
Kenmore
110.76862692
Dryer - Kenmore Dryer Model 110.76862692 (11076862692, 110 76862692) Parts
Kenmore
110.77834792
Dryer - Kenmore Dryer Model 110.77834792 (11077834792, 110 77834792) Parts
Kenmore
110.796228
Dryer - Kenmore Dryer Model 110.796228 (110796228, 110 796228) Parts
Kenmore
110.97263100
Dryer - Kenmore Dryer Model 110.97263100 (11097263100, 110 97263100) Parts
Kenmore
110.97263800
Dryer - Kenmore Dryer Model 110.97263800 (11097263800, 110 97263800) Parts
Kenmore
110.97561420
Dryer - Kenmore Dryer Model 110.97561420 (11097561420, 110 97561420) Parts
Kenmore
11060012000
Dryer
Kenmore
11060012001
Dryer
Kenmore
11060012002
Dryer
Kenmore
11060022010
Dryer
Kenmore
1106012510
Dryer - ELECTRIC DRYER
Kenmore
11060172000
Dryer
Kenmore
11060172001
Dryer
Kenmore
11060172002
Dryer
Kenmore
11060202990
Dryer
Kenmore
11060212990
Dryer
Kenmore
11060222510
Dryer - DRYER
Kenmore
11060222511
Dryer - ELECTRIC DRYER
Kenmore
11060232000
Dryer
Kenmore
11060232001
Dryer
Kenmore
11060232002
Dryer