Whirlpool 341241 - Multi Rib Belt - 92-1/4" | PartSelect.ca
Multi Rib Belt - 92-1/4" – Part Number: 341241
Multi Rib Belt - 92-1/4" – Part Number: 341241 Multi Rib Belt - 92-1/4" – Part Number: 341241 Multi Rib Belt - 92-1/4" – Part Number: 341241 https://partselectca.azureedge.net/Schematics/Maytag/UTGT4VNQ.gif

Multi Rib Belt - 92-1/4"

24 Reviews

Your Price

CAD$19.72

PartSelect Number PS346995
Manufacturer Part Number 341241
Manufactured by Whirlpool

This dryer drum belt has four ridges, three grooves and is 1/4" wide.

This part works with the following brands: Kenmore, Whirlpool, KitchenAid, Norge, Roper, Maytag, Magic Chef, Crosley, Admiral, Estate, Amana, Inglis, Jenn-Air, Hoover.

This part works with the following products: Dryer.

This part fixes the following symptoms: Will not tumble | Noisy | Will Not Start | No heat or not enough heat

Videos For installing this part.

Related Parts Additional or alternate parts to consider.

Part Photo
Description
Price
Availability
(1)
PartSelect: PS11743765
This part provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. This arm attaches to the idler pulley wheel.
$17.93
In Stock
(14)
PartSelect: PS373087
NOTE: This kit is for 29" wide dryers built in 1965 or later. Please verify model # before ordering as may not work for all models. This kit comes with one multi-rib belt, two drum support rollers, one idler pulley, fo...
$34.38
In Stock
Questions & Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 353 reviews What's this?
105 of 112 people found these instructions helpful
Parts Used:
  • Multi Rib Belt - 92-1/4"
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
Customer:
Michael from San Antonio, TX
Broken tumbler belt
1. Removed the screws from the lint catcher
2. Removed the bolts from upper rear of dryer
3. Pried off the dryer top from the front (it rests on rear hinges)
4. Disconnected dryer door wiring
5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall when it loses support)
6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance
7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler)
8. Placed new belt on tumbler; reinserted tumbler
9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first)
10. Made sure belt and tumbler seal were properly installed
11. Replaced parts in reverse order
The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

89 of 104 people found these instructions helpful
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers, Socket set
Customer:
Edward from Andover, NJ
Dryer was sqeaking loudly when running
I Looked on internet sites for this type of problem.
Most sites said the support rollers could cause this.
I found your site PartSelect and with help of your diagrams of the machine ordered the parts I thought were needed plus other parts that might cause the problem.
With machine torn down I replaced the rollers.
I had also ordered the main drive belt and idler assembly with the rollers and these also needed replacement. It is a good idea to order other suspect parts when doing this type of repair since you can return the parts not needed.
Your return policy is great.

Edward Brennan

Help other customers find the most helpful instructions.

Were these instructions helpful?   

54 of 60 people found these instructions helpful
Parts Used:
  • Multi Rib Belt - 92-1/4"
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Customer:
Gary from Oakland, MD
Broken belt - drum would not turn
Started out taking the back off, then found online that access is from the front and much easier to get to. Simply pop the hinges in the back of the top panel and then the front of the top is popped off. From there, it is easy to remove the old belt, clean the innards (found 31 cents) and replace the new belt. It was a little disconcerting to see the idler pulley laying loose inside, but the diagram showed exactly how to put it back in place, with the new belt keeping it in place.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

46 of 54 people found these instructions helpful
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers
Customer:
Thomas from Oneonta, NY
Dryer made a loud noise and vibrated badly
First I made sure the unit was unplugged. I popped the top of the unit with a slotted screw driver, lifted the top up and rested it against the wall behind the dryer. I removed the two screws - one on each side in front on top of the dryer cabinet. Then I tipped back the front panel of the dryer slightly with the door of the dryer closed. I unclipped the door switch with a slotted screw driver and then lifted the entire front panel including the door off of the the two floor clips on bottom. I set the front panel aside. Next I lifted the large drum slightly to dislodge the rollers in back and slid the drum back slowly while sliding the thin belt back on the drum until the drum was out of the unit and the belt was detached and loose. Then I cleaned the unit thoroughly, vacuumed all lint and dirt and wiped down the outside of the large drum with mineral spirits to make sure it was totally clean and smooth. Then I removed the two rollers and the roller shafts at the back of the unit following the directions enclosed. My slip-ring pliers came in handy to remove the retaining rings on the roller shafts. I replaced the rollers and roller shafts and the supplied washers and spacers as per the instructions. I sprayed a little WD-40 on the surface of the rollers and it stopped all squeaking and vibration of the drum. Next I replaced the front drum pads and runners as per the instructions. I then slid the drum back in place taking care to slide the new belt back around the drum in the same position as the old belt. Now came the difficult part - laying on the floor and reaching under the drum I positioned the belt around the motor shaft and tension pulley. This must be done by "feel" and must be done correctly!! Follow the instructions on the positioning of the belt very carefully and make sure it is in the correct position on the drum, motor shaft, and tension pulley! Next, get up and rock the drum up and down slightly to make sure it has engaged the two rear rollers properly. Rotate the drum manually one or two turns to make sure the belt is in the correct position. Then replace the front door panel by dropping it onto the two clips at the base of the unit and taking care to replace the door switch in reverse order of taking it out. Then replace the two screws at the top front on each side of the unit to secure the front panel. Lower the top of the unit back in place, plug in the dryer, turn it on and enjoy the lack of noise you have created.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

41 of 52 people found these instructions helpful
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Customer:
Angela from Houston, TX
Dryer would stop running after several minutes. Once cooled it would start again. Motor worn out and binding.
Remove back cover
Raise top
Remove filter assembly
Remove front cover and drum

Tip: Use an end wrench on the fan and another on the pully shaft of the motor to remove fan from motor prior to removing motor from cradle.

Vacuum everything while disassembled

Remember to take your time and not force anything and this will go smooth.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Customer Reviews
Average Rating:
24 Reviews
4.9
out of 5
Filter By Rating:
  • 5 Stars
    21
  • 4 Stars
    3
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:

Model Cross Reference

Brand
Model Number
Description
Kenmore
10686294140
Dryer
Kenmore
10686294340
Dryer
Kenmore
10686294540
Dryer
Kenmore
10686294740
Dryer
Kenmore
10686294840
Dryer
Kenmore
110.6085299
Dryer - Kenmore Dryer Model 110.6085299 (1106085299, 110 6085299) Parts
Kenmore
110.7080299
Dryer - Kenmore Dryer Model 110.7080299 (1107080299, 110 7080299) Parts
Kenmore
110.765340284414694
Dryer - Kenmore Dryer Model 110.765340284414694 (110765340284414694, 110 765340284414694) Parts
Kenmore
110.76702690
Dryer - Kenmore Dryer Model 110.76702690 (11076702690, 110 76702690) Parts
Kenmore
110.76862692
Dryer - Kenmore Dryer Model 110.76862692 (11076862692, 110 76862692) Parts
Kenmore
110.77834792
Dryer - Kenmore Dryer Model 110.77834792 (11077834792, 110 77834792) Parts
Kenmore
110.796228
Dryer - Kenmore Dryer Model 110.796228 (110796228, 110 796228) Parts
Kenmore
110.97263100
Dryer - Kenmore Dryer Model 110.97263100 (11097263100, 110 97263100) Parts
Kenmore
110.97263800
Dryer - Kenmore Dryer Model 110.97263800 (11097263800, 110 97263800) Parts
Kenmore
110.97561420
Dryer - Kenmore Dryer Model 110.97561420 (11097561420, 110 97561420) Parts
Kenmore
11060012000
Dryer
Kenmore
11060012001
Dryer
Kenmore
11060012002
Dryer
Kenmore
11060022010
Dryer
Kenmore
1106012510
Dryer - ELECTRIC DRYER
Kenmore
11060172000
Dryer
Kenmore
11060172001
Dryer
Kenmore
11060172002
Dryer
Kenmore
11060202990
Dryer
Kenmore
11060212990
Dryer
Kenmore
11060222510
Dryer - DRYER
Kenmore
11060222511
Dryer - ELECTRIC DRYER
Kenmore
11060232000
Dryer
Kenmore
11060232001
Dryer
Kenmore
11060232002
Dryer