Heating Element Connection Wire Kit

took a couple differant parts to fix the dryer. i ordered one part at a time. i was expecting to wait the 5 days for shipping but i got home from work the next day of odering parts and they were there waiting for me on my doorstep. all three times i ordered. this website is the best site to order parts. i wont go to another website or store if i need to order parts for appliances. u guys have my business for life. thumbs up.

I started by removing the Washer from the utility room. Then I disconnected the vent and the power supply. Put the dryer on its front, (you may want to lay a blanket down to protect the finish.) Then using a nutdriver I removed the nuts which hold the back in place. Removed and replaced the defective element. Replaced the back with the nuts. I then up-righted the dryer, moved it back into position, reconnected the vent and the power supply and tried it out. It worked!

removed the back panel. located the section for the heating element and unpluged the tow wiresand repalced the thermostat. it took only 15 to 20 minutes. and instead of buying one I saved a lot of money

This dryer is 30 plus years old. I am a 71 year old female that has never taken on this type of repair. First I very carefully ordered all parts possibly associated with this problem. Watched all videos available for this model. Could not find one at Parts Select that addressed this particular dryer. Model number was correct. Finally found YouTube video that addressed an "Old Kenmore Wood Top". It showed the correct way to remove the Heating Element unit. Also Parts Select never mentions that fuses and sensors are not "polarized". Very important info for a novice. But Google helped me with that. Heating Element is "polarized", very important not to cross wires. I did order a couple Heating Element Connection Wire Kits that were not needed for this repair. Got all parts replaced, put dryer back together, crossed my fingers and turned it on, so far it has been working really well. I chose to replace all the parts I did because of the dryers age, plus I am not familiar with multimeters. Didn't want to risk one old part messing up a new part. Thank you Parts Select.
It is not a 2 hr. repair, but I worked slowly, didn't want to make any mistakes. It would be good if everyone is aware of some of the above information and the YouTube video done by an individual on this particular dryer.

Boyfriend stated it was simple, he removed the back and replaced the part using a few everyday tools.

*as with all electrical repairs I unplugged dryer from the outlet*

I disconnected the wires to the heating element, removed the 2 nut screws holding the heating element in place and removed the defective heating element. It looked like the heating element had darkened on the lower end and the wire terminals definitely looked like they had built some resistance that lead to the connection wire melting.

I slid the new heating element in and replaced the 2 screws. I cut the melted portion of the connection wire about 1/2" beyond the melted area and stripped the wire jacket exposing clean wire. I took the connection kit & clean wire lead, divided the wires into 2 groups on each end and braided them together and twisted them to a hand tight grouping. I then took the lead cap and twisted into onto the braided wire connection until it was also hand tight and snug.

I then reconnected the heating element connection wire back to the terminal end of the heating element and made sure all connections were snug.

I plugged the dryer back in, reset the dryer by turning the dial to a timed setting then back to off. I set the heat to low turned the dial to a time dry and turned on the dryer to ensure the element heated up and that the wired connection was secure. After 20 - 30 seconds, the element maintained heat and no issues were found with the fixed wire.

I replaced the dryer back and all screws and reconnected the vent hose. Dryer has worked great for the last few weeks with no issues. I was really surprised it was that easy to fix.

The repair was really easy and I loved the DIY videos they were great, not many tools needed to do these repairs that was great. The only thing is this didn't solve my issue.

Good

I saw some videos suggesting you remove the back panel.Then I saw a video where only the kick plate was removed and the element was removed that way.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant amount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.

The replacement parts are truly easy to exchange. Everything is located behind the rear panel. A few fasteners needed to be undone. What's really important is another video that explained what should be "checked" when a dryer malfunctions. VERY IMPORTANT viewing. I spent an afternoon going over the front inside and rear of my dryer. I'll probably get another ten years from my dryer thanks to this site data and videos.