Please keep in mind this housing is for single drain outlet models only. This part will not work for dual outlet port models.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Leaking | Not draining
This part works with the following products:
Dishwasher.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WD19X10020 replaces these:
AP2039468, 876925, WD19X10023
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water pump leaking at value stem.
Removed built-in washer and turned on side. Removed complete motor and pump to work on bench (easier). Removed pump and replaced with new unit. Instructions did not tell what to do with white plastic tube for shaft(goes with lip facing motor onto shaft)Be sure rubber seal is pressed into pump fully. Inch pound instructions were not helpful. Remember how much pressure it took to take off it helps to install new pump. Inch pounds is not what most people know or use. Reassemble unit, flipped on end and tested for leaks before replacing under cabinet.
HOUSING LEAKED AROUND WIRE.ROLLERS WERE BROKE,LOWER ARM DIDN'T WORK RIGHT HALF THE TIME
REPLACE 2 THE ROLLER WHEELS THAT WERE BROKE.THEY JUST POPPED ON AND YOU JUST POP THE STOPPER BACK IN. THE CHANNEL LOCKS WERE USED THE UNSCREW THE LOWER SPRAY ARM TOWER.ONCE IT STARTED,ALL I HAD TO DO WAS REACH IN AND FINISH UNSCREWING IT WITH MY HAND THEN SCREW THE OTHER BACK IN.I HAD MY HUSBAND TO MAKE SURE IT WAS SNUG AFTER I DID IT. MY HUSBAND CHANGED THE DRAIN PUMP HOUSING BUT I DON'T KNOW WHAT HE DID.ALL I KNOW IS IT DIDN'T TAKE VERY LONG FOR HIM TO DO IT.
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Len
April 17, 2018
I have standing water in the tub of my dishwasher after the cycle is complete. The pump is working but not completely emptying the tub. Could the solenoid be the cause?
For model number GSD3360D00SS GE DISHWASHER
Hello Len, thank you for your question. If there is water left in the dishwasher after the unit has finished the cycles, you would want to replace the Drain Solenoid and Bracket Assembly Part Number: WD21X10268. This valve opens in order for the water to drain out of the dishwasher. If it is "stuck" open it can let water back in. I hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Nancy
January 17, 2023
My dishwasher is leaking from below. The repairman thinks it is pump #311. Why is there calcification on the metal next to the pump housing and on my floor? Could something else be wrong also?
For model number GSD2300V00BB
Hello Nancy, Thank you for writing. This could be caused by hard water that is leaking from the faulty pump. We hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Richard
August 16, 2017
Won't drain. I did replace the solenoid, but draining is very weak. Any ideas?
For model number GSC3500R20WW
Hi Richard,
Thank you for your inquiry. I would suggest checking to see if there are any blockages in your drain tubes and the drain pump. If you do not have any blockages you might want to test your pump mechanism (or drain pump and motor assembly). I hope that helps. Good luck with your repair.
