Little to no heat when broiling | Element will not heat | Little to no heat when baking | Oven not heating evenly
This part works with the following products:
Wall Oven, Range, Microwave Oven Combo.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WB44K5009 replaces these:
AP2030967, 260838, WB44K5009, 344895
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
11 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
February 21, 2018
Does this come with the attachment (3) clips?
For model number JKP56B0A2BB
Hi John, Thank you for the question. The clips are sold separately. The part number is Part Number: PS243701. Hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
Eric Skidmore
May 6, 2019
My GE True temp broiler element burned out suddenly while using. What is the correct part # to order, and is it difficult to replace?
For model number JKP15WOA2WW
Hello Eric, thank you for inquiring. This Broil Element part PS249244 is the correct replacement for your model.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Esther
November 26, 2019
Will this broiling element work with my model number? Please let me know as I would like to order the part if it does work
For model number JRP15B0W5BB
Hello Esther, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS249244 for the top Broil Element int he oven. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Hector
November 28, 2019
Why the new broil element I purchase from you has a wider diameter than the one my wall oven had?
For model number JRP14G0T1BB
Hello Hector, Thank you for the question. Checking the model number you ordered the correct top broil element for your appliance. At times the manufactures will make changes to the parts over time and they may appear different but should still fit and work on your appliance. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jim
March 7, 2023
We are going to order Broil Element select number PS249244 and Baking Element PS249291. Do we need new screws or anything else or do we use the existing ones .
For model number JKP27BOA3BB
Hi Jim, thank you for reaching out. You will need screws, part number PS234427, for both heating elements. You will also need a single heating element support clip, part number PS243701, for the broil element. We hope this helps!
Is wb44k5009 the correct broiler element for this oven?
For model number JKP15AOA2AA
Hello Nan, thank you for your question. Yes, Broil Element part PS249244 is the correct replacement for your model.
Was this helpful?
Thank you for voting!
B
March 11, 2018
I cannot find the broiler element for our GE profile drop in oven. Can you help?
For model number JMP31WC2WW
Hello B,
Thanks for your question. The broil element compatible with your model is part number PS249244. Your model contained an extra 0 as part of a series digit which can be removed for the correct model list.
I hope this helps.
Was this helpful?
Thank you for voting!
Timothy
March 7, 2019
Heating elements for top oven, upper and lower element part numbers?
For model number JRP28BJ1BB
Hello Timothy, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Part Number: PS249244 for the top broil element and PartSelect Number: PS249249 for the bottom Bake element. Thank you for your inquiry, good luck with this repair!
Do you no if this will work on a GE model# j kp07g0j5bg?
For model number J KP07G0J5BG
Hello Lance, thank you for your question. That part will not work unfortunately. The broil element for this unit is PartSelect Number: PS249411. Please enter the part number into the site for current price and availability. Good luck with your repair.
Hello Marty, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS249244. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 23 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The broiler element caught fire and burned out while I was broiling a steak.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power. So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther. An appliance repairman was at my house that day fixing my dryer seal. He was able to pull the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky!
Other Parts Used:
Dianne from Rockville, MD
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
66 of 74 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top broiler element went out
FIRST MAKE SURE THE OVEN IS OFF!!!! I chose to shut it off at the breaker panel. Remove the two screws that attaches the broiler element to the oven. Gently pull it out. Unplug the two cable wires that are attached. Replace it and install the same way.
Other Parts Used:
Kim from Garland, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
39 of 42 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacement of heating element
If I'd had the Nut driver, it would have taken 15 -20 minutes or less. Went to Ace Hardware, bought the nut driver for $4.99.
Turn off the power at the box! Turn off the oven as well. Four screws total. Two to hold it in place and two that connect the element to the source.
First I removed the two screws that hold the element in place. I pulled the element out about 2 inches. Two more screws connect the element wires. I disconnected the element, threw it away, then connected the new element. I put the element in place, then replaced the screws that connect the power. Finally, I replaced the screws that hold the element in place.
Kimberly, El Cerrito, California
Other Parts Used:
Kimberly from El Cerrito, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
16 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broiler element would not heat; bake element did heat
Removed the oven racks, removed screws holding element hanging support from roof of oven, removed screws holding plate of element to rear of oven. CAREFULLY worked element loose from back of oven and gently alternated pulling each side of element (near the base) until connecting wires came free of insulating batting. Pull too hard and the connecting wires can break loose and disappear behind the batting. Once freed, disconnected both wires with socket (use pliers for extra grip on flat part of connectors, if necessary), removed element, braced new element on bottom of oven, aligning connectors to now-free wires. Re-attached with the new screws that came with the element (attachment points on element are threaded; do not reuse old screws as the threads may not match), gently re-inserted element into insulating batting at rear of oven, reattached hanging support, then replaced element plate screws.
Can be difficult to work in small, deep ovens....many oven doors can be removed. If so, remove oven door and use a chair as a support...lie on your back on the chair and hang your head and arms in the oven.
Other Parts Used:
Brad from San Carlos, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
12 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The upper element for broiling went kaput!
The two dollar socket set from Xmas 20 years ago had the right size socket..
Long arms are advisable.
The lower element still plugged in while the upper wires were just hanging there surrounded with fluffy white insulation fuzz, I wondered, " Could I bake a potato for my yearning and hungry family?"
When I explained the situation to my retired father in Arizona he said simply, "I wouldn't."
The new element popped in. It got really red, and, kinda like watching my toaster toast, the show was pretty much over after it heated up.
took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping
Other Parts Used:
Becky from Piedmont, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
7 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
element burned out
It's so simple most people could mannage the repair. Turn oven off. Remove oven door and shelves. Use a nut driver to remove mounting screws. Pliers to pull quick connect terminated wires off element terminals. Use pliers to push connectors onto new element,wires may connect to either terminal. Nut driver for screws to mechanically mount new element. Replace shelves and door. First time element gets hot it will burn off oils and dirt, not a problem but do it now not later.
Other Parts Used:
John from Durham, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
5 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
TOP OVEN BROILER ELEMENT BURNED OUT & BROKE
1) TURNED OFF THE POWER TO THE OVEN. 2) REMOVED THE TOP DOOR AND RACKS. 3) REMOVED THE 2- 1/4 HEAD HEX NUTS AND PULLED THE ELEMENT FORWARD ENOUGH TO EXPOSE THE ELECTRICAL CLIPS TO THE ELEMENT. REMOVED THE CLIPS WITH A PAIR OF NEEDLE NOSE AS ADDED GRIP. 4) PUT THE WIRE CLIPS ON THE NEW ELEMENT AND REVERSED THE ABOVE PROCEDURES.
Other Parts Used:
HIDDEN HILLS from TONASKET, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace the heating coil in convection oven
[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.
[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back into the rear oven wall. [3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them. [4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone. [5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.
Other Parts Used:
Victoria from San Jose, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old broil element started burning with being on OFF position requiring need to turn off breaker and cut element in two to stop progression of burn
1. Turn breaker off at breaker box. 2.Disconnect old broil element. Pull electric wires out 3-4 inches from BACK of oven. Clamp wires or tie off so they do not retreat behind back oven wall. INSTALL wires to new element and secure back plate. Install NEW clamps to new element. Switch on breaker and check operation.
