Part Location Diagram of 131475320 Frigidaire Heater Assembly
See part 25 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Heater Assembly

★★★★★
★★★★★
2 Reviews
$231.69
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS2378363
Manufacturer Part Number 131475320
Manufactured by Frigidaire
Product Description

Heater Assembly Specifications

This dryer heating assembly has 5/16" terminal on the housing.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part works with the following products:
Washer Dryer Combo, Dryer, Washer.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Tappan.
Part# 131475320 replaces these:
AP4501537, 1553336, 131475320, 131234600, 131475300, 131475320
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
  • 5 Stars
    2
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.4 / 5.0, 8 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Dryer still turned, but would not heat
Had to remove tub to get to rear wall to make the repair and then put it back together in reverse order.
Other Parts Used:
  • CAROLE from MONTICELLO, AR
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
53 of 79 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Had a professional do the install. He had difficulty aligning the cabinet so that it did not rub against the dryer drum. The parts you mailed me worked fine and resolved the problem. Thanks. Even having to pay the installer saved me 50% on the total job.
Installer unscrewed the screws on the upper panel, loosened the pulley holding the rubber drum cable, and pulled the drum up and out of the unit. With the rear heating element exposed, he unplugged the wire connections to the heating element, unscrewed the four screws holding the element to the rear panel and took the element out. Then he installed the new heating element by re-applying the four screws into the rear panel. He then replaced the thermal limiter which was directly at the right of the heating element by unplugging the wire connections to the thermal limiter and then unscrewing the thermal limiter from the rear panel. The process to install the new thermal limiter was the reverse process. He didn't install a new High Limit Thermostat because there was one attached to the new Heater. When all the new parts were installed, he reinstalled the drum by pushing the rear nub of the drum into the whole at the center of the heating plate. He then placed the rubber drum cable around the drum with the rough service facing the drum, placed the cable on the pulley and adjusted the tension of the cable with a screw driver. He then reinstalled the front panel by aligned the screw holes and reinserting and tightening the screws.
Other Parts Used:
High Limit Thermostat Thermal Limiter - Limit 220
  • michael from jupiter, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
47 of 61 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer wouldn't heat
First: Remove front and top cover
Second: remove electrical cover assbly
Third: motor belt removed
Fourth: drum assbly and bearing shaft and bracket bearing replaced
Now I need urgently (already ordered) the thermostat and glide drum
Other Parts Used:
Rear Drum Bearing Kit Drum Support Bearing Dryer Drum Bearing Bracket
  • Ivan from Guaynabo, Puerto Rico, AL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
18 of 29 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced burned out heating element
Not having the repair manual made the repair more difficult. Prior experience made the job somewhat easy. Had to study every move to make sure no parts were not broken but overall the repair went without any problems. I found out that the bearing plate was removable to facilitate removal and replacement of the heating element. Advise if you are doing a repair of an appliance you don't know much about, take your time and everything should go well for you.
Other Parts Used:
High Limit Thermostat
  • George from ALLENTOWN, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer heater broken
Removed top cover.
Lowered control assembly.
Removed front door assembly.
Removed drum.
Removed heater assembly.
Removed support bearing and bracket using existing bonding ball.
Re-assembled in reverse order.
Other Parts Used:
Dryer Drum Bearing Bracket Drum Support Bearing
  • Johnny from PINEBLUFF, NC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
DRYER MADE A LOT OF NOISE
Took the top dryer cabinet apart to replace all the above parts plus the dryer belt. Because of its age decide to replace all the parts from the above list.
Three major problems: none of the video reviews showed this type of dryer. Some parts were practically impossible to get back together. Difficult getting the top square. The top of the cabinet picture did not indicate how the top was to be installed.
After 23 hours finally got it back together. Then it would not start. Discovered a wire had come loose. The dryer works fine now.
Other Parts Used:
Dryer Drum Bearing Bracket Drum Glide - White Lower Front Felt Seal with Adhesive Front Upper Felt Seal with Adhesive Drum Support Bearing
  • Jerry from ROCKWALL, TX
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My heating element had gone out
Don’t do like I did and undo the drummer from the back of that thing pulled off the bearing
Other Parts Used:
  • Van from BLUFFDALE, UT
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not heat at all.
I watched the video you had. Did what the man said, checked out the parts, and orded the new ones. Then installed , as per video. It was Fun.
Other Parts Used:
  • ricky from okeechobee, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
1 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

12 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gene
February 11, 2018
Does high level thermostat (ps446428) come with heater assembly ps2378363? I'm not sure if high level thermostat is ok.
For model number GLET1041AS2
PartSelect logo
Hello Gene, Thank you for the question. Yes the High Limit Thermostat that is at the top of the element in the picture comes with the new element. Good luck with the repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Mark
October 2, 2017
Does this part come with the thermostat that is in the picture? Thank you.
For model number GLEH1642DS1
PartSelect logo
Hi Mark, Thank you for the question. Yes the High Limit Thermostat that is at the top of the element in the picture comes with the new element. Good luck with the repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Paul
February 25, 2020
Dryer will not heat up is the heater element the answer
For model number 41794812301
PartSelect logo
Hi Paul, Thank you for your question. If the dryer is not heating up, there are some parts that you will need to check to see which one is causing the issue. You will need to check the heating element, the thermal limiter, the high limit thermostat, the cycling thermostat, the cover assembly and moisture sensor and the electronic control board. You will need to test the parts with a multi-meter. Here is a link to one of our videos on YouTube that you may use as a general reference on how to use one, https://www.youtube.com/watch?v=bWC44fHn0As. To check the electronic control board, you will need to inspect it for signs of damage, wear or burn marks. If it shows any of these signs, it will need to be replaced. If it is the electronic control board causing the issue, part number 134216300, it has been discontinued by Frigidaire and you will need to contact them for information on a replacement part. Their telephone number is 1-800-374-4432 extension 0. If they provide you with a part number for the replacement part, you may call us back with it and we can verify if we have it available for you. You may also be able to locate the part you need by trying the following: Using a search engine to type your part number and see if other retailers still have this part in stock. Visiting online stores such as eBay and finding sellers that have this part. Trying retailers and repair stores in your local area to see if they have the part in their inventory. Talking to a local repair technician, who may have the part you need, or may be able to repair your existing part. If you are unable to find one through these methods, there is a company called Circuit Board Medics that may be able to repair it for you. Their telephone number is 1-800-547-2049. We hope this helps. Thank you and have a great day.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Jerry
August 2, 2018
Are there any instructions available to aid in the installation of the new heating element.. ?
PartSelect logo
Hi Jerry, Thank you for your question. There is a video on our website that you can reference on how to install the heating element. The the dryer in the video may not show exactly like the one you have, but it will give you a general idea on how to install the part. You will find the video under part number PS418120. Also, here is the link to the video, https://www.partselect.com/PS418120-Frigidaire-131553900-Heating-Element-Assembly.htm?SourceCode=3&SearchTerm=131553900. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Sally
May 6, 2019
Takes forever to dry anything...very low heat...do you think i need the whole heater assembly or just the heater coil...in your opinion..thank you
For model number 417.98702891
PartSelect logo
Hi Sally, Thank you for your question. If the dryer is not heating as it should, there are some parts that you will need to check to see which one is causing the issue. You will need to check the heating assembly, the thermostat, the thermal limiter and the timer. If it turns out to be the heater assembly, the coil is available separately. The part number listed under your model number for the coil is PS451032. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Paul
January 27, 2022
SERIAL # XE90401404 I'm only getting partial heating. Top of the back of the dryer is very hot bottom no heat. Do I need a new heater?
For model number FEX831FS2
PartSelect logo
Hello Paul, thank you for your question. Not necessarily. We recommend trying Thermal Limiter - Limit 220 PartSelect Number PS419402 first. We have an installation video for you to access. Then try just the element PartSelect Number PS451032. We hope to hear from you soon.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Steve
February 10, 2020
Does the heater assembly come with high limit thermostat?
For model number FLSE60RGS1
PartSelect logo
Hello Steve thank you for your question. Yes the High Limit Thermostat will come with that assembly. Good luck with the repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Donald
April 4, 2022
Dryer is getting very hot. When door is opened while running the coil in the back is cherry red and little sparks fall off of coil. Is this caused by a bad element or?
For model number FEX831CS0
PartSelect logo
Hello Donald, Thank you for the question. We suggest testing the thermostats with a Multimeter to see if they are faulty and allowing the appliance to over heat. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

Was this helpful?
Thank you for voting!
Related Parts:
Maria
November 21, 2023
kenmore dryer 970-c90802-00 video on heating element 131475320.. can you send me the video We are so distort as we can not find it
For model number kenmore dryer 970-c90802-00 video on heating element 131475320
PartSelect logo
Hi Maria, thank you for contacting us. We have attached a relevant video, which may not be of the exact model but will help you with the process. We hope this helps.

Was this helpful?
Thank you for voting!
Christopher
November 23, 2019
What other parts are advised to replace with a heating element
For model number 41797812701
PartSelect logo
Hi Christopher, referring to model 41797812701, I am unsure what you are referring to. Do you have a specific symptom with your fridge you are trying to fix? Thank you for your question and good luck with your repair!

Was this helpful?
Thank you for voting!
  • 1
  • 2
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2378363
Manufacturer Part Number: 131475320
Brand
Model Number
Description
Kenmore
41790802990
Washer Dryer Combo
Kenmore
41790802991
Washer Dryer Combo
Kenmore
41790802992
Washer Dryer Combo
Kenmore
41790807990
Washer Dryer Combo
Kenmore
41790812990
Washer Dryer Combo
Kenmore
41790812991
Washer Dryer Combo
Kenmore
41790812992
Washer Dryer Combo
Kenmore
41790814000
Washer Dryer Combo
Kenmore
41790814001
Washer Dryer Combo
Kenmore
41790814002
Washer Dryer Combo
Kenmore
41790817990
Washer Dryer Combo
Kenmore
41791702000
Washer Dryer Combo
Kenmore
41791702001
Washer Dryer Combo
Kenmore
41792702200
Washer Dryer Combo
Kenmore
41793702200
Washer Dryer Combo
Kenmore
41793702201
Washer Dryer Combo
Kenmore
41793802200
Washer Dryer Combo
Kenmore
41793802201
Washer Dryer Combo
Kenmore
41793812200
Washer Dryer Combo
Kenmore
41793812201
Washer Dryer Combo
Kenmore
41793814200
Washer Dryer Combo
Kenmore
41793814201
Washer Dryer Combo
Kenmore
41794702300
Washer Dryer Combo
Kenmore
41794712400
Washer Dryer Combo
Kenmore
41794802300
Washer Dryer Combo
Kenmore
41794802301
Washer Dryer Combo
Kenmore
41794812300
Washer Dryer Combo
Kenmore
41794812301
Washer Dryer Combo
Kenmore
41794814300
Washer Dryer Combo
Kenmore
41794814301
Washer Dryer Combo
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service