GE WD12X10304 - RACK SLIDE END CAP | PartSelect.ca
RACK SLIDE END CAP – Part Number: WD12X10304
( Grid squares measure 1x1 inch )
RACK SLIDE END CAP – Part Number: WD12X10304 RACK SLIDE END CAP – Part Number: WD12X10304 https://partselectca.azureedge.net/Schematics/GE/00125643i03.gif

RACK SLIDE END CAP

Your Price

CAD$5.23
Special Order

PartSelect Number PS2370502
Manufacturer Part Number WD12X10304
Manufactured by GE

The Rack Slide End Cap is a white one-inch plastic part which replaces the end cap for your dishwasher rack, preventing your rack from sliding too far. If you find the dish rack is causing the door to not close properly, it may be due to the part being worn out or damaged. All you need to complete this repair is a small flat blade screw driver. Simply pop out the cap with a smaller flat-blade screwdriver and snap the new one into place. If the rear cap needs to be replaced you will need to remove both front caps and slide the rack completely off for full access. It is important to note that this part is sold individually, and more than one may be required, depending on your repair. An inexpensive part, it can be a good idea to purchase several at a time to have on-hand when needed.

This part works with the following brands: General Electric, Hotpoint, Kenmore.

This part works with the following products: Dishwasher.

This part fixes the following symptoms: Not cleaning dishes properly | Door latch failure | Door won’t close

Videos For installing this part.

Questions & Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Peggy
July 20, 2017
How do I remove the upper end cap …
Hi Peggy, try using a smaller flat blade screwdriver to press in on the retainer clip. This is the small part that would be sticking out through the back of the metal rack slide. Once this has been pushed in, you should be able to pull it out by the end to remove it. I hope this helps!

15 people found this helpful.

Was this helpful?
Jimmy
July 20, 2017
I need to replace the right and left end cap on my top dishrack, is this what I need? Does the purchase come with one or two end caps and can I use this one for L and R?
Hi Jimmy, yes this is the part you will need. This replacement end cap WD12X10304  can be used for the left or the right side. Only one will come with this purchase. Best of luck with this repair!

7 people found this helpful.

Was this helpful?
Tracey
July 20, 2017
I was able to get the end caps off but I cant get them back on. How do I reinstall the rack and caps?
Hi Tracey, to reinstall simply press down on the retainer clip on the end caps WD12X10304 and push them into the slot until you hear them click into place on the railing. Please let us know if you have any further questions.

2 people found this helpful.

Was this helpful?
Scot
February 8, 2019
The soap is still in the soap compartment after the the dishwasher is done. It acts like no water is being used at all.
For model number GSD6200J00CC
Hello Scot, thank you for your question. If the soap isn't being released automatically the most likely issue is the dispenser itself. You would want to to replace the dispenser PartSelect Number: PS958966. Good luck with your repair!

1 person found this helpful.

Was this helpful?
Alex
February 18, 2019
Machine has started making a roaring noise but only when spraying. It is still cleaning fine and drains properly. I have checked and cleaned a small amount of debris from the filters removed the spray arms and checked them, they are clean, flow freely, and spin freely. Any thoughts?
For model number GLD4408R10BB
Hello Alex, thank you for your question. It sounds like an issue with the circulation pump, PartSelect Number: PS1017766. I would recommend replacing that part. I hope this helps!

1 person found this helpful.

Was this helpful?
Kelley
February 3, 2020
Do not know the model but i need the part that spins in the bottom and cleans the dishes.
Hi Kelley. We would be happy to do some research to find you the correct parts. However, we need your model number and the brand name to locate any information on this. Model numbers can be short or long, and could have a mixture of numbers and letters. Thank you for your question and good luck with your repair.

1 person found this helpful.

Was this helpful?
Alex
February 18, 2019
I asked a question earlier and it was suggested that the problem was with the circulation pump. How is this accessed on this model....need i pull it from under the counter and turn it over. thanks for your help.
For model number GLD4408R10
Hello Alex, thank you for your question. The circulation pump and motor, part number PartSelect Number PS3652479, can be accessed by pulling the dishwasher out and laying it on its back. I hope this helps!

Was this helpful?
Elaine
December 23, 2019
Soap dispenser door does not open to release soap when machine is started.
For model number GDF520PGD1BB
Hi Elaine, most likely replacing dispenser will fix this issue. Thank you for your question and good luck with your repair!

Was this helpful?

Customer Repair Stories

Average Repair Rating: 4.5 / 5.0, 73 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Joseph from Haymarket, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Parts Used:
WD35X20994, WD35X21041, WD12X10304, WD35X21038
Worn/broken plastic parts were causing misery
Order arrived two days after being placed. Super easy to remove the old, worn, broken plastic parts and replace with new. Everything popped right on just as shown in the diagram. Our happiness with our dishwasher has increased 100%. BTW, thanks to the very helpful, friendly and knowledgeable staff at PartSelect.com -- next job, replace the ice maker in the freezer!
414 of 433 people found this instruction helpful.
Was this instruction helpful to you?
michael from perry hall, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Parts Used:
WD35X21038, WD12X10327, WD12X10304, WD12X271
wheel replacement
Pulled the end cap off and replaced the wheel.
most of the parts were for future repairs
229 of 430 people found this instruction helpful.
Was this instruction helpful to you?
Dave from Littleton, CO
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WD30X98, WD12X10327, WD12X10304, WD12X332
Parts were old and worn out
The repair was easy. A couple turns of a screwdriver was all that was necessary to remove the rollers and slide assembly. The I simple installed the new rollers. Slid the slide into place between the rollers and then added the back caps to the slide. Replaced the rack rollers on the top basket and then slid it into position between the new slides. Once in place, I attached the end caps to the front of the slide. Simple and quick.
29 of 40 people found this instruction helpful.
Was this instruction helpful to you?
Warren from Stillwater, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WD35X20994, WD28X10391, WD28X25960, WD12X10304, WD12X10054, WD12X10391
Top and bottom rack were rusted thru
Bottom rack - slide the old one out, slide the new one in. The rack came came with the wheels, so I didn't use the replacement ones.
Top rack - remove the rail end caps - they will likely break so order new ones. Slide the rack out. Remove the rotating spray arm and then remove all the brackets. I was able to re-use the old brackets and didn't need the replacements. Install the old brackets on the new rack, install the spray arm, and slide the new rack back into the rails. The new top rack also came with wheels installed, so I didn't use the replacement ones. Once the rack is back in the rails, install new rail end caps. Put them in sideways and facing into the washer. Straighten the caps and turn them into place. Be careful with the rail caps - they break easy and are expensive. Make sure they hold the top rack in place, and that's it.
29 of 41 people found this instruction helpful.
Was this instruction helpful to you?
Patrick from San Jose, CA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Parts Used:
WD28X10284, WD28X10049, WD12X10304
Upper and lower racks starting to rust
Removed the lower rack and upper rack after removing the end caps on the rail. Order new replacement end caps. The originals will likely break because the plastic becomes more brittle over time. Unsnap the upper washer arm from the original upper rack and snap onto the new one before inserting it into the rails.

The trick is replacing the end caps. Using needle-nose pliers, bend the indented edge of the rails out so you can attached the new end caps without trouble. After they are in place, use the tip of the needle-nose pliers to restore the indentation on the edge of the rails to lock the caps in place.
24 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Tracey from Cedar Hill, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Parts Used:
WD12X10304, 61005520, 12001991, W10857122
No Ice or water dispencing
I first read about others with the same problem on your web sight and figured if they could do it so could I. Anyway the directions are a little hard to read but it was very informative and straight forward. I took the advice of one of the do it your-selfers when it came down to removing the spring. Be careful not to loose it. Everything was there that I needed and went on without a hitch. Now it was time to see if my repairs were done correctly. Pow! Everything worked. This is a great web-sight to buy parts if you are a do it your selfer. Easy to follow instructions.
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Roger from Simi Valley, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
Parts Used:
WD35X20994, WD35X20994, WD12X10304
broken wheels and attachments
Everything snapped on quite easily. I was releaved to not have to replace "everything."
7 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Raymond from ansonia, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers
Parts Used:
WD12X10304
Very, very easy. Took about 5 minutes. The end cap was on and working. And the repair company would charge $65 just to come out and look at it. It costs $9.00 to fix it. I am moving on to the refrigerator next. Very satisfied. Shipping is well worth the money. Ray D, Ansonia, CT
Old cap was already off and had string on it. Cut the string. Placed end cap over. Used needle nose pliers to open metal rail a little and put in new cap. Locked right in. That was easy. Thanks again.
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
William from Nacogdoches, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Wrench set
Parts Used:
WD01X10175, WD12X10304
Dishwasher wouldn't drain completely
Removed the dishwasher from the cabinet. Turned it on it's top side. Removed the exit hose from the pump with a nut driver and replaced the flapper. Reconnected the hose to the pump.
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Robert from Old Lyme, CT
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WD12X10327, WD12X10304
2 rollers and end caps were broken were broken
Pulled the basket out the appliance and took what was left of the roller off and replaced them and slid the basket back onto the slide channel into the appliance. Then snapped the end caps on. Almost too simple. Less money than it costs to have the service man ring your door bell.
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
4 Reviews
4
out of 5
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    1
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
5
-
Verified Purchase
Fit perfectly and easy to install.

Easiest part to replace. Fit as it should.

5
-
Verified Purchase
Dishwasher part

Received quickly. Easy to install.

5
-
Verified Purchase
worked

I have been fighting with my old dish washer for about 5 years now, and was going to get a new 1 so I debated the cost difference, new dish washer $1000, new part $5.......hmmmm

1
-
Verified Purchase
Wrong part

After inputting my Brand Model number the site led me to a part. Took the chance. Stupidly bought two thinking it’d be good to have a spare but it was the wrong size and did not work for me

Model Cross Reference

Brand
Model Number
Description
General Electric
1200L02
Dishwasher - DISHWASHER
Kenmore
18385
Dishwasher - DISHWASHER
General Electric
3000B10
Dishwasher - DISHWASHER
General Electric
3000W10
Dishwasher - DISHWASHER
Kenmore
361402891
Dishwasher - Kenmore Dishwasher Model 36.1402891 (361402891, 36 1402891) Parts
Kenmore
3631401190
Dishwasher
Kenmore
3631401191
Dishwasher
Kenmore
3631401590
Dishwasher
Kenmore
3631401591
Dishwasher
Kenmore
3631401592
Dishwasher
Kenmore
3631401890
Dishwasher
Kenmore
3631401891
Dishwasher
Kenmore
3631401892
Dishwasher
Kenmore
3631402190
Dishwasher
Kenmore
3631402191
Dishwasher
Kenmore
3631402192
Dishwasher
Kenmore
3631402590
Dishwasher
Kenmore
3631402591
Dishwasher
Kenmore
3631402592
Dishwasher
Kenmore
3631402890
Dishwasher
Kenmore
3631402891
Dishwasher
Kenmore
3631402892
Dishwasher
Kenmore
36314031000
Dishwasher
Kenmore
36314031001
Dishwasher
Kenmore
36314032000
Dishwasher
Kenmore
36314032001
Dishwasher
Kenmore
36314038000
Dishwasher
Kenmore
36314038001
Dishwasher
Kenmore
36314039000
Dishwasher
Kenmore
36314039001
Dishwasher

All brand logos are trademarks of their respective owners.

The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.

Copyright © 1999-2021, Eldis Group Partnership. All rights reserved.