Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Daphne H - September 24, 2022
Verified Purchase
Easy stove repair
Out largest burner wasn’t working on different temperatures but with this new part it’s back to normal. My husband installed it saving us h7ndreds of dollars in repair man services.
★★★★★
★★★★★
Lawrence M - December 17, 2019
Verified Purchase
Worked perfectly - easy to find in the catalogue
The installation instructions were easy to follow and the part is working very well.
★★★★★
★★★★★
Michael H - November 27, 2018
Verified Purchase
Worked as expected
Quick shipping, fit perfect, problem solved
★★★★★
★★★★★
Wendy G - November 3, 2018
Verified Purchase
painless--no drama
after hours of looking measuring-- ect part came and it was the right one--because the MODEL NUMBER ON STOVE was no a VALID number for it so we needed to go by visual--- all is good back cooking with element-- have given your site to small maintenance repair man. thanks again---Wendy in Flin Flon, Manitoba
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No control of right front burner (dual burner)
The burner would work but you could not regulate the heat. I ordered and replaced the control switch for that burner. The part was like for like and reasonably priced compared to other websites and dealer. The picture showed that it was identical. I ordered one day and it was here the next. I had drawn a diagram of where the wires went on the old switch so it was very easy to replace. Probably took me 15 minutes or so. Works perfectly and by buying from this website it saved me a few bucks.
Other Parts Used:
Jeff from Clinton, IA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
18 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner light was on - burner control spun freely
Looked up the part, ordered it, and it was there in 3 days. It was slightly different than the old control, but a very well-written set of instuctions detailed which wires to move to which terminal. The entire repair took about 30 minutes, including moving the range out, replacing the control, and push the range back in place. Works perfectly.
Dual burners stay on hi all the time. No regulation.
The hardest part was getting the correct part. I trusted the on line number and the first part I received was incorrect. I should have taken the part number off the old switch. When I did, I found out that the part number changed when I tried to order it. When the part came, the wiring instructions were not even close. I just took one wire at a time off the old switch and put it on the same terminal of the new switch. The repair was/is very simple made complex and too much time because of a wrong part and incorrect wiring instructions. As far as getting the incorrect and correct parts through the mail it was very fast. Received both parts in less than 3 days. A bonus is that I sent the old switch back for a rebate. Thanks for that.
Other Parts Used:
Peter from whitesboro, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
10 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rotary switch for the dual control burner failed
Removed range from cabinets then approximately 6 sheet metal screws from the front of the range and two 1/4" sheet metal screws from the side to remove the front and top of the range. Lifted the cook top removed the two screws from the rotary switch and followed the directions included with switch to connect the wires. In reverse order reassembeled the range. Quick & Easy
Other Parts Used:
Robert from Belvidere, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
7 of 10 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right front burner had no heat control. (High heat when on "Low")
Pull range out of the "hole", and spin so that back of range is accessible. Remove cover over top "control area" on back of range. (Four screws that happen to be the same size as the magnetic socket that holds the interchangeable tip on a cordless screw gun. Simply remove this tip, and use the tip holder as a magnetic nut driver!). Remove the knob by pulling gently straight off. Remove black plastic retaining nut under where knob was. Inside are two small screws that hold the switch in place. Remove these screws with a magnetic screwdriver (If you drop these screws and lose them, you'll have a hard time finding them. Very small!!). Carefully follow enclosed instructions to move the wires from the old switch to the new switch. Put back together in reverse order.
Other Parts Used:
John from Ocoee, FL
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
7 of 11 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Overheating dual element
Not only did we (my wife did help) replace the dual element but afterwards we realized the control switch was not functioning properly and so that was replaced as well, and now our appliance works as intended. Also the instructions, are helpful as well. We used care not to force or over tighten anything and with two sets of eyes and the extra hands everything went much better. Anything that was removed was noted as to it's location and replaced .
Remove the top back panel to expose the switch. Remove the switch knob & mounting bezel and then unscrew the 2 mounting screws from the front. Replace the wires one by one and follow the enclosed directions in the event that this is an upgrade for an older switch. Remount the switch from the front and replace the back panel.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
December 20, 2017
The smaller burner of my dual burner doesn't heat when the control is set to the #4 position, every other number setting heats up without hesitation. Will the switch, part # ps236785 correct this?
For model number JB940W0B4WW
Hi Robert,
Thank you for your question. It does sound like it is probably an issue with your switch. You can test it with a multi meter to be sure. If your switch is fine then it may be your element that is the issue. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Charlie
January 9, 2019
When i turn on the small burner on my dual burner, the whole burner comes on, not just the small burner. I am looking at your switch p/n wb24t10063. Is that the correct part for this Kenmore stove? Also am i correct in thinking the switch is the most likely part to replace?
For model number 911.99004990
Hello Charlie, thank you for your question. Yes, the burner switch would have to be replaced. The switch regulates the small or large burners separately. The part number is PartSelect Number: PS236785. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joe
December 2, 2022
What is the jumper for in the package with the WB24T10063 switch
For model number Jb900sk6ss
Hello Joe, thank you for your question. Jumper wires are electrical wires with connector pins at each end. They are used to connect two points in a circuit without soldering. You can use jumper wires to modify a circuit or diagnose problems in a circuit. We hope this information will help you.
Was this helpful?
Thank you for voting!
Ray
October 17, 2019
The front right dual element burner ; only the outer burner works when turned clockwise
When turned counter clockwise nothing even on inner burner
Would wb24t10063 fix this or do you think i need the burner itself/ thanks ray
586 372 1260
For model number jp989bkbb
Hello Ray, thank you for your question. The most likely issue is the switch itself. Before replacing the switch you can test the element itself, to be sure that isn't the issue. Here is a link for testing.
https://www.partselect.com/Range-Stove-Oven+Surface-Burner-Testing+repair.htm
I hope this helps!
Was this helpful?
Thank you for voting!
Russ
January 16, 2020
The hot light stays on all the time
For model number JP989BK1BB
Good Day Russ. Thank you for your question in regards to your unit (Model Number JP989BK1BB). Based on our research, you may need to replace the Infinite Control Switch (PartSelect Number PS1016429) for on of your burners, or the burner itself. You will need to test the elements with a multi-meter in order to determine which one is faulty and needs to be replaced. We hope this helps. Best Regards.
Was this helpful?
Thank you for voting!
Karl
May 27, 2022
I changed the Dual Burner Control Switch (WB24T10063) because it would not operate. The corrected the issue but now the red over light sis always on even when the control is off The oven goes off but the red light stays on.
Help!
Karl
For model number RB536WH4WW
Hi Karl,
Thank you for your question. If the indicator light remains on when the burner is off, check the wiring to make sure that it is not loose and that it is connected correctly. Usually if the indicator light remains on, there is an issue with one of the switches and it will need to be replaced. You should test the switches with a multimeter to if they have continuity. Unplug your appliance before beginning.
Remove the back panel in order to access them. Inspect the wires near the switch for any signs of burning, or overheated wires and terminals. If no issues are found, remove the switches in order to test them. Using a multimeter on Rx1 mode, test for continuity by touching the L1 and H1 terminals with the probes. Once you have completed that test, touch the probes to the L2 & H2 terminals.
If your test results indicate that there is no continuity between one or both sets of terminals, you need a replacement infinite switch. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
Go to U.S. site
Stay on this site
Special Order
