TO GO BACK TO NATURAL WILL NEED QTY 4 PRT# PS2332486
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Range.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Westinghouse.
Part# 316243723 replaces these:
AP4427119
Customer Repair Stories
Average Repair Rating: 3.3 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Had to go from nat gas to lp
Replaced uper orifice n adjusted oven as instructed.
Other Parts Used:
Tom from Wappapello, MO
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wood Burning Oven
The Appliance light was installed in a wood burning oven used by a commercial bakery. The entirely masonry oven is used to cook a specialty product with origins in Brazil. We first drilled a 11-3/4 hole from the inside of the oven starting at the fire brick that passed through the concrete block outer shell of the oven to accommodate the insulated wiring to the on/off switch outside the oven. Then we commissioned a special steel cowling to enclose the the back and sides of the lamp so that the lamp faced down, instead of out and the back of the fixture was protected. The back of the lamp was attached to the insulated switch wires, then the custom lamp housing with filled with fire proof insulation. The entire lamp housing was then attached to the upper face of the masonry wall with 1/4" x 4" masonry bolt head screws. This type of installation was required because the oven overall size of 6' tall x 4' wide X 4' ID dimensions required a heat resistant light to illuminate 15 shelves of product being produced. The oven lamp purchased works perfectly for the new oven. By the way, the oven does not have a brand, as it was created as a one of a kind, the brand of the oven lamp was taken from a Kenmore Gas Range.
Other Parts Used:
Thomas from YAMHILL, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Stanley
November 6, 2018
Just asked about oven do you have part number for that pressure regulator
For model number Ffgf3012twa
Hello Stanley, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is PartSelect Number PS438464. Thank you for your inquiry, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Eddie
January 10, 2019
I need to change the range to natural gas for the stove top. It is currently lp
For model number FGF316DSE
Hello Eddie, thank you for your question. To go back to NAT gas you will need to order a quantity of 4 of part number PartSelect Number PS2332486. To change the oven you would adjust the components on the valve itself. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Eddie
January 10, 2019
I need a conversion kit to natural gas from lp gas
For model number fgf316dsf
Hello Eddie, thank you for your question. The conversion kit for this unit is PartSelect Number: PS2358939. the conversion kit part number PS2358939 is necessary to change the top burners to LP gas. To change the oven you would adjust the components on the valve itself. I hope this helps!
Was this helpful?
Thank you for voting!
Stan
November 6, 2018
Your showing conversion kit for top burners don't i need to change anything for oven
For model number Ffgf3012twa
Hello Stan, Thank you for the question. You'll need to convert the pressure regulator to LP and adjust the orifice on the gas valve turning it two and a half turns down. Hope this helps!
Was this helpful?
Thank you for voting!
BILL
November 21, 2018
Is a lp gas conversion kit necessary for this range? Is the range converted by adjustment of the components?
For model number ffgf3012twa
Hello Bill, thank you for your question. Yes, the conversion kit part number 316243723 is necessary to change the top burners to LP gas. To change the oven you would adjust the components on the valve itself. I hope this helps!
Was this helpful?
Thank you for voting!
Linda
March 2, 2020
Does this kit convert from lp to natural gas?
For model number Ffgf3012twa
Hello Linda, Thank you for the question. This is for converting to LP for use with LP Gas. We hope this helps.
Was this helpful?
Thank you for voting!
Ingrid
February 17, 2022
I have changed the top burners what do I do for the oven. Do I need an additional part
For model number Ffgf3011lbf
Hi Ingrid,
Thank you for your question. To convert your oven from natural gas to propane you will need to access the regulator and adjust the plastic plug on the cap. Take a wrench and unscrew the cap. Under the cap, you will find a plug. The gas type that the regulator is set for is closest to the cap which would be natural gas. Take the plug out, rotate and place the opposite end inside the cap and snap it in. The plug will have the gas type molded into it. If you need more information, you will need to consult your owner's manual. If you have any questions, please let us know. We are open 7 days a week. We look forward to hearing from you!
Hello Bernard, thank you for you question. If you want to convert this to LP Gas, then you will need to have the propane orifice in the LP Conversion Kit PS2358939. Good luck with this repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.