This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can be used for the front and the rear support, as designed by the manufacturer, and mounts to the inside cabinet wall. Replacing this part is an easy repair, and will require a small flat blade screwdriver, a putty knife, and a soft hammer. Remove the crisper and shelf from the refrigerator before replacing the support. The crisper cover front support is held in place with a locking pin. To remove the old part, you will first need to push the pin into the interior of the cabinet using the screwdriver, and then you can pull the support out with a putty knife. If you cannot get the pin out you can use a flat-blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator After removing the pin and attaching the new support, simply use the soft hammer to lock the new pin in place.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Refrigerator Crisper Cover Support - Front
Troubleshooting
This part fixes the following symptoms:
Door won’t open or close
This part works with the following products:
Refrigerator.
This part works with the following products:
Frigidaire, Kenmore, Crosley, Electrolux.
Part# 241993101 replaces these:
AP4427109, 1513082, 240423701, 7241993101
Customer Reviews
Average Rating:
★★★★★
★★★★★
13 Reviews
4.8
Filter By Rating:
5 Stars
10
4 Stars
3
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Bill T - July 8, 2023
Verified Purchase
Great
Easy repair, new part fit right in. Longer taking shelf out then putting new support in
★★★★★
★★★★★
Kevin E - March 10, 2020
Verified Purchase
Easy repair
5 minute job. The part fit perfectly.
★★★★★
★★★★★
Suzanne D - July 6, 2019
Verified Purchase
Great website easy to find part
Wonderfully easy to follow video instructions with a easy to use website! We will be back!
★★★★★
★★★★★
Paul H - March 26, 2019
Verified Purchase
Worked as it should
Easy to replace, and finally have solid refrigerator shelves again.
★★★★★
★★★★★
Joan B - March 18, 2019
Verified Purchase
one went in easily and the 2nd one is arguing
The part arrived in great condition and is holding up quite well
★★★★★
★★★★★
Vincent M - March 9, 2019
Verified Purchase
Worked as expected
Easy fix
★★★★★
★★★★★
Peter C - February 4, 2019
Verified Purchase
Perfect fit
Was an exact replacement part.
★★★★★
★★★★★
Yadu G - January 19, 2019
Verified Purchase
Thanks the part was perfect
I like how easy the shopping experience was parts came fast and in good condition excellent job
★★★★★
★★★★★
Shari S - January 7, 2019
Verified Purchase
Easy to Install
Thanks to the video, the parts were easy to replace, and work very well.
★★★★★
★★★★★
Peace A - December 11, 2018
Verified Purchase
Easy repair
Great
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 35 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Support studs were broken
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.
had broken sheves on the doors and the crisper drawers weren't suported
The only difficult aspect of the job was getting the old shelf support stud removed from the refrigerator wall - the support was broken off too short to allow vise grips to hold it. I had to use two screwdrivers to get under and then pop out the stud to the point I could get the pliers to hold. Everything eles pretty much just "fell together" very easily.
1.Got on line to Partselect ordered the parts we needed .they arrived Quickly and in good condition 2.Except the tray was sent in error delaying the repair. 3.contacted Partselect costumer services for assistance 4.Followed their direction and reorder the correct one hoping the correct one would arrive .it did the next day .5.On to repair, removed broken stud with panel stud puller with the aide of a putty knife to spread the pressure of tool stud came out 6.reinserted new stud 7.replaced the new upper crisper drawer cover glass not included . 8.Upper Crisper pan to complete the repair. 9.all in all successful with the help of Partselect superior parts and helpful guides.
Broken plastic guides on both crisper drawer covers. Upper crisper pan broken. Broken supports.
Remove both crisper pans and covers. Discard old frames and re-use glasses. Use two screw drivers to gently pry out broken supports. Top broken off smooth on one support. Unable to grasp with pliers to pull out. I drilled a small hole in the center of the large expansion pin. I screwed in a small sheet metal screw. Used side cutter pliers to grasp screw and gently rock back and forth to remove center of large pin. Plucked out broken pieces with needle nosed pliers. Gently tap in expansion pins to install new supports. The rest is simple re-assembly using new parts. "Nothing to it but to do it."
most importantly on the page with the necessary part..cripser support for the refrigerator--- there was a brief insructional video on how to properly dislodge the broken part and replace it with the new showing the simple tools needed. I am not handy at all but it took me all of two minutes thanks to the helpful video.
Replacement of bins were simple the crisper cover supports were a little more time consuming since the manufactured piece were glued in. I used a tool that has a 30% tip and hooked the support and pulled in out part of the way and pulled the rest out with my fingers. All in all a simple job...I took the opportunity to do an addition cleaning of the inside of fridge with my extra time. Would also like to say that my parts were delivered within 24 hours of ordering them and the website made purchasing easy and no second guessing, since the model had an exploded version of all the parts available. Thank you
The shelving brackets are install much like a blind rivet. I simply used a punch and gently pushed in the plastic center pin / mandrel. I then used a butter knife as a wedge to pull out the shelving supports enough to grab them with a pair of pliers. Simple to do!
Parts Supply had a YouTube video to show it was done. This is one of the best sites to get parts there is. Easy to use, tells you how to install them easily. Thanks Parts Supply, I'll be back whenever I need a appliance part.
I used pliers to get the remaining shelf support studs out, then the new ones just snapped right in place. Very easy repair!
Other Parts Used:
Kristina from Woodbridge, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
11 of 25 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
13 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Vince
July 20, 2017
When I try to pull pry the support off, the inner liner of the fridge is coming out with it. How do I take it out without breaking anything?
Hello Vince, in center of the supper there is a small circle, you will have to puncture this to remove the support without damaging your fridge. First, we recommend pushing it in, using a putty knife to pry the support off, and then using a pair of pliers to remove the pin. If you cannot get the pin out you can use a flat blade screwdriver to push it down and out of sight and it will not harm anything in your refrigerator. I hope this helps!
26 people found this helpful.
Was this helpful?
Thank you for voting!
Kesha
July 20, 2017
Just realized I need front AND back supports… can I order this part for both the front and the back of my fridge??
Hi Kesha, this crisper cover support 241993001 can be used for both the front and the rear of your fridge, as it was redesigned by the manufacturer. Best of luck with this repair.
18 people found this helpful.
Was this helpful?
Thank you for voting!
Rich
November 14, 2018
You answered another question saying that part# 241993101 is now used for the front and back support. The back support was just a pin so how does it work now?
For model number FFHS2611LBNA
Hello Rich, Thank you for the question. This would depend on the model number of the appliance. On the previous customers model it was the front and rear. For the model number you have provided, you need PartSelect Number PS2358879. There is a video listed under the part informatio0n on how to install. Hope this helps, good luck with this repair!
So my crisper drawers keep falling off and I assumed it was because my supports are broken. But I looked at them closely and they seem to be fine and the right make/model. Is my fridge expanding or my drawers shrinking? Is that a thing? How do I fix this
Hi Alice, sometimes the lines in a refrigerator can warp. What you can do is make sure your drawers are not damaged and that your supports are in good condition on the unit. Please let us know if you have any further questions.
6 people found this helpful.
Was this helpful?
Thank you for voting!
Joseph
March 27, 2019
My bridge element does not work anymore, I used a griddle and after the only thing that worked was the front and rear elements
For model number GLEF396AQC
Hello Joseph, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS820333. Thank you for your inquiry, good luck with this repair!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Winston
June 3, 2019
The coil is iced up
For model number Glhs238zds
Hello Winston, thank you for inquiring. The cause of this may be due to either a faulty Defrost Thermostat part PS469522, the Adaptive Defrost Control Board part PS2582247, or the Evaporator Fan Motor part PS3419839. We hope this helps.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Gail
November 15, 2018
Will the part still be able to install if there is a small break on the installation hole?
For model number ffhs2622mba
Hello Gail, thank you for your question. Yes, the part should still work. If you find its loose, you may want to glue it to the inside of the fridge. I hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Roger
March 3, 2018
My water filter will not release so that I can change filters. I had removed the old one to check the date and replaced it back into the fixture. Now when I push the release button, nothing happens. Can you help?
For model number GLRS234ZAB2
Hello Roger,
Thanks for your question. You may need a new water filter base to fix this issue, part number PS976499.
I hope this helps.
DOES THIS CRISPER COVER SUPPORT WORK FOR THIS MODE
IF YES ITS THE FRONT ONE
For model number FRS23KF6EM8
Hello Vivian, thank you for your question. Based on your model number, we find the correct part to be PartSelect Number PS2358880. We hope to hear from you soon.
1 person found this helpful.
Was this helpful?
Thank you for voting!
John
October 4, 2022
Something happened electrically that won't let my ice dispenser work. It makes ice but won't dispense. The same is happening to my ice water, it won't come out when lever is pushed. The main wires coming up to feed these 2 is dead. I want to get this working again even if I have to run 2 more wires manually from where the wires are hot. Is this possible?
For model number FRS6HR35KW1
Hi John,
Thank you for your question. There is a wire harness with light listed for the dispenser. The part number listed under your model number for the wire harness is PS12746212. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to the inside cabinet wal...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2358880
Manufacturer Part Number: 241993101
