Part Location Diagram of WH13X10037 GE Triple Water Inlet Valve
See part 805 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Triple Water Inlet Valve

★★★★★
★★★★★
1 Review
$114.11
  Special Order
PartSelect Number PS2354072
Manufacturer Part Number WH13X10037
Manufactured by GE
Product Description

Triple Water Inlet Valve Specifications

The triple water valve or inlet valve in your washer connects to the water source and solenoid wires, and ensures the tub has the right amount of water entering it. If your washing machine continues to fill after it is full, or if it fills slowly, you may need to replace this valve. Before you begin this repair, be sure to disconnect the water and power sources from your washer. This part is sold individually.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Leaking
This part works with the following products:
Washer.
This part works with the following products:
General Electric.
Part# WH13X10037 replaces these:
AP4412517
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 4.1 / 5.0, 4 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Water fill valve leaking
Got this 1 1/2 year old machine from a friend that was disgusted that it had leaked water and ruined her kitchen wood floor. She didn't want it anymore. I took it home & hooked it up in the driveway with a garden hose and located the leak at the water fill valve solenoid. The valve description is confusing as it's a two solenoid ( hot & cold ) valve , but described as a " triple water valve". The OEM part came and was exactly the same as the one I removed. The machine works great and replaces my 12 yr old Kenmore washer that has given me trouble free service.
Other Parts Used:
  • Mark from Peachtree City, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
61 of 82 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water kept dripping in washer
Shut water valves off to washer. Then Removed the two hoses from washer. Removed the top panel off the washer. Disconnected the two wires to the thriple water valves. Unscrewed the two mounting screws. Using a magnetic screw driver will help not dropping them and possibly-losing -them. Next-Removed the old thriple water valve and installed the new one. Reconnected everything back in the order that I had took it all part. Also, A good thing to do is replace the rubber washers in the two hoses connected to the washer. (As it was needing to be done). Turn water back on to washer. (Problem solved no-more constant dripping of water In Tank of Washer!
Other Parts Used:
  • stanley from SHARON, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
9 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
THE CELLULOID TRIPLE WATER INLET VALVE WAS LEAKING INTO THE WASHER.
FIRST, TURNED OFF THE MAIN VALVE INTO THE HOME..AND BLED THE LINES. USED A SMALL BUCKET AND DISCONNECTED THE LINES FROM THE WASHER. TOOK THE PLATE OFF THE WASHER AND DISCONNECTED THE OLD INLET VALVE CONNECTED THE NEW VALVE AND REPLACED THE COVER PLATE. SINCE I HAD THE MACHINE DISCONNECTED, I PUT NEW WATER LINES AND REPLACED THE HAT AND COLD WATER VALVES WITH NEW 1/4 TURN BOILER BALL VALVES. TURNED THE WATER BACK ONTO THE HOUSE AND RAN THE FAUCET SO THERE WOULD BE NO AIR IN THE LINES WHEN I TURNED THE WATER ON TO THE WASHER.
Other Parts Used:
  • BARBARA L. from WHITEHALL, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No hot water
Verified there was 110 volts at the connection at the triple water valve. Removed two 1/4" socket screws and used pliers to slide hose clamp off valve inlet. reversed procedure, turned water back on, problem solved.
Other Parts Used:
  • CHARLENE from BENSALEM, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

5 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Michael
February 27, 2019
So when the washing machine isn't running, it drips water into the tub. The inlet hoses have already been replaced. Should i try replacing the triple water inlet valve?
For model number gtwn4250m1ws
PartSelect logo
Hello Michael, Thank you for contacting us. I suggest to check the water valve with a multimeter. It should be reading between 200-400ohms. Good luck with your repair!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Pete
March 20, 2019
I can fill the washer with hot water, but the cold side will not work. It seemed to become a problem very quickly. At first, the cold would flow for about 10 seconds and stop. Then it would do it again until finally not working at all. Does it sound like the triple water inlet valve? Thanks.
For model number GTWN4250M0WS
PartSelect logo
Hello Pete, thank you for your question. Yes, it could be the Triple Water Inlet Valve part PS2354072, but may also be the Pressure Switch part PS2354068 or the Water Pressure Switch Hose part PS272183. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Sebra
September 9, 2021
Start the machine, it beeps twice and then nothing. Put in new board asm mounded and in didn't help. Do we need new inlet valves or something else
For model number GRWN5150MOWS
PartSelect logo
Hello Sebra, thank you for your question. We have researched the model you have provided, and we would suggest the lid switch. You can test the lid switch with a multimeter. Unplug the washer and set your multimeter to the lowest ohms of resistance. If it does not read any continuity, then your lid switch is indeed faulty. Part number PS1482372. It could also be the water inlet valve. Part number PS2354072. Inspect the screens found inside the valve. Clean out any debris you find. You should be able to pop them out with a flat head screwdriver. Do use caution when handling the screens as they are irreplaceable. Set your multimeter to the ohms resistance scale X 1. Place each of the meter's probes to one terminal. Because the reading can vary from brand to brand and from model to model, there is no one reading you should receive. However, if your test produces a reading of infinity, then the solenoid is bad and the water valve should be replaced. We hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Phil
November 28, 2022
When the water temperature on my GE washer is set to use a mixture of hot and cold water, I hear a loud pulsing or pounding in the pipes. It does not happen when set to use “tap cold” or “hot” water. Is this a mixing valve problem? Thanks!
For model number GCWN4950D 2WS
PartSelect logo
Hi Phil, thank you for reaching out. Yes, the triple water inlet valve seems to be faulty, you need to replace it with part number PS2354072. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.

Was this helpful?
Thank you for voting!
Lawrence
May 21, 2019
I'm have having a problem with my GE washer. When i set knob for hot water it only dispenses cold water. Sometimes i do receive hot water after a few attempts. But mainly it returns back to cold water after a few seconds. Please let me know if this is the part that i need or what part might solve problem thanks.
For model number GCWN4950D2WS
PartSelect logo
Hello Lawrence, thank you for your question. It sounds like the issue is either the valve or the temperature sensor probe. We would recommend replacing the PROBE SENSOR ATC Part #: PS2355966 and PartSelect Number: PS2354072. I hope this helps!

Was this helpful?
Thank you for voting!
  • 1
;
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2354072
Manufacturer Part Number: WH13X10037
Brand
Model Number
Description
General Electric
GCWN4950D2WS
Washer - WASHER
General Electric
GCWN5050M0WS
Washer
General Electric
GCWN5050M1WS
Washer
General Electric
GLWN5050M0WS
Washer
General Electric
GLWN5050M1WS
Washer
General Electric
GPRE8350K0WT
Washer
General Electric
GPRE8350K2WT
Washer
General Electric
GPRE8350K3WT
Washer
General Electric
GRWN5150M0WS
Washer
General Electric
GRWN5150M1WS
Washer
General Electric
GTAN4250M0WS
Washer
General Electric
GTAN4250M1WS
Washer
General Electric
GTAN4450M0WS
Washer
General Electric
GTAN4450M1WS
Washer
General Electric
GTAN5050M0WS
Washer
General Electric
GTAN5050M1WS
Washer
General Electric
GTWN4250M0WS
Washer
General Electric
GTWN4250M1WS
Washer
General Electric
GTWN4450M0WS
Washer
General Electric
GTWN4450M1WS
Washer
General Electric
GTWN4950L0WS
Washer
General Electric
GTWN4950L1WS
Washer
General Electric
GTWN5050M0WS
Washer
General Electric
GTWN5050M10WS
Washer
General Electric
PTAN6250M0WT
Washer
General Electric
PTAN6250M1WT
General Electric
PTWN6050M0WT
Washer
General Electric
PTWN6050M1WT
General Electric
PTWN6250M0WT
Washer
General Electric
PTWN6250M1WT
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service