The Grate Foot is a black rubber part which attaches underneath the grate in order to protect your stovetop from being scratched, which it does by cushioning the grate on your gas range. If this part appears visibly broken or no longer holds in place, which can happen to these feet over time, then it should be replaced. Check your model number and user manual to see if this part is right for you. Because this part is sold individually, make sure to order the quantity that you require. We generally recommend checking all of the grate feet on your appliance and replacing them at the same time, since it is an inexpensive part and they tend to wear out at around the same rate. Spares are good to have in the event of future failures. Before beginning this repair, ensure that the surface is cool to the touch. Simply pull the worn or cracked foot out and install the new grate foot. This process should not require any tools or accessories.
Average Repair Rating: 4.2 / 5.0, 15 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The cooktop had a shorted out burner control.
Unpllug the cooktop and turn off the gas supply. Remove the grates and burners.(they just lift out). Using a torx screwdriver, remove all the torx screws below where the burners sit. There are three screws per burner, except the power burner which has only two screws. Genly lift the stainless steel cooktop, separating it from the rest of the enclosure. Hold the electrodes with one hand, while gently twisting and pulling the wire connector off. Now, remove the aluminum covered foam piece. You will now have acess to the wiring harness assembly. Disconnect the quick connectors and replace with the new assembly. Re-assemble in the reverse order and you're done. About 1.5 to 2 hours. Good Luck
A rubber grate foot on my range top had worn out. I pulled the worn foot out and installed the new grate foot with no tools or accessories. Good as new! Now I don't have to worry about the grate scraping my range top and scratching the paint. I also ordered extras so I won't have to wait if another wears out.
Upper left rack roller broke, had to replace rack adjuster assembly
First I had to take out the end caps on both sides of the upper rack - easy enough - you push in the direction of the arrows and they open up and come off. Then I took the rack off. Using the smallest allen wrench I could find in my ex-husband's set that he left behind (yay!), unscrewed the old rack assembly. The (blue) adjuster level doohickey popped out when the old assembly came off, but it was easy enough to fit that back in properly by looking at the right-hand one that was still in place. All I had to do was fit the new rack assembly into place, put back a few screws, and slide the rack back into place. Put the end caps back on and you're done. Maytag should offer free replacements for this part, IMO- the wheels are too flimsy to begin with, our dishwasher is only four years old, and the new part is pricey, at $29.45 a pop.
After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Other Parts Used:
Anne from Jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber Grate foot worn or missing.
Replaced worn or missing Grate Foot with new ones. Took less than 5 minutes.
Other Parts Used:
Terry L from Puyallup, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
Other Parts Used:
Richard from Stratham, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rubber grate foot failed
Cut off approx. 1/8" in length for correct fit.
Other Parts Used:
Gary from HENDERSONVLLE, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Yellow flame on large burner
Removed top grate. Removed burner head . replaced with new burner head. Replaced grate.Very simple replacement. Old burner head was warped with age.
Ask our experts a question about this part and we'll get back to you as soon as possible!
9 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barbara
November 21, 2017
How many grate foot come in an order?
For model number JGP329SET3SS
Hi Barbara, Thank you for the question. According to the online description,this part is sold individually.Hope this helps!
13 people found this helpful.
Was this helpful?
Thank you for voting!
Douglas
October 9, 2017
What type of glue works best on the grate foot? Thanks.
For model number WB02T10461
Hi Douglas,
Thank you for your inquiry. You should need no glue to install the part. Just insert the new grate feet right on the grates. I hope this helps. Thank you and have a great day!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Mark
November 19, 2017
The control panel does not work at all. The burners can be lit with a match, but the igniter does not work also. I tried pressing the range lock out for 3 seconds, and also 9 0 for 3 seconds. I also tried unplugging the range for a while. I am sure i have power and gas. Thank you.
For model number PGS975SEP3SS
Hi Mark,
Thank you for your question. It is likely that you will have to replace your electronic control board if your control panel is not functioning at all. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
John
February 25, 2018
In package
Grate foot
Part number: Ps2353327 how may come to one pack
For model number JGP975SEK1SS
Hi John, Thank you for the question. According to the online description for this foot," Because this part is sold individually, make sure to order the quantity that you require." Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Dave
January 25, 2022
1. How many grate feet/pkg? (doesn't say); also, $6 for how many? 2. Where's the WB00X7108 - 2oz tube of adhesive? Thx, - - dk - - Model is a GE Profile gas cooktop....No #....I can try to send a picture
Hello Dave, Thank you for the question. According to the discription "Because this part is sold individually, make sure to order the quantity that you require." In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. We are looking forward to hearing from you!
Was this helpful?
Thank you for voting!
Barb
April 11, 2022
Is the price really ONE knob for $8.00
For model number PC2S930SEL3ss
Hello Barb, Thank you for the question. The Grate Foot is sold individually. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Susan
January 27, 2023
Does part PS2353327 fit this model? If not, what part does?
For model number KSGG700ESS1
Hello Susan, thank you for your question. The correct part for your model is PS988447. They are sold as a kit of 4 Grate pads. We are pleased to have been able to help.
Looking for the little bumper feet for the bottom of the stove grates on my Kitchenaid gas stove. Found this: PS2353327, but it doesn’t look the same.
For model number YKSDB900ESS2
Hi Tracey, thank you for your question. Whirlpool provides a kit of 5 burner feet. The part number listed for the burner grate foot kit is PS389174. If you would like to place an order for it, please call our customer service line and anyone will be happy to assist you. If you receive them and they are not correct, we have a 30 day return period. We have included a link to our return policy. We look forward to hearing from you!
Is there rubber tape that will cover the underside of the grate so the grate does not scratch the stainless steel as it's being places on the stovetop?
For model number PGS930YP5FS
Hello Michael, Thank you for your inquiry. We do not show any rubber tape available for the grates, only the rubber grate feet. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
