Maytag/Maytag_Thumb/50074.gif
See part 13 in the diagram
Replacing your Maytag Range Top Burner Igniter play video
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.ca

Top Burner Igniter

★★★★★
★★★★★
7 Reviews
$41.28   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS2082000
Manufacturer Part Number 74004053
Manufactured by Whirlpool
Product Description

Top Burner Igniter Specifications

This top burner igniter comes with a mounting bracket.
How Buying OEM Parts Can Save You Time and Money play video

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will Not Start | Gas igniter glows | but will not light | Element will not heat
This part works with the following products:
Range, Cooktop.
This part works with the following products:
Maytag, Magic Chef, Jenn-Air, Amana.
Part# 74004053 replaces these:
AP4093621, 704111, 74004053, 74004053, 7432P100-60
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

16 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Roi
August 22, 2017
Installed top burner igniter and can't get spark .Other burner works fine .Could new part be defective any ideas
For model number jdg8130ads
Hello Roi, thank you for contacting us. The electrode only makes the spark, unless it was corroded it would not be defective. Its the part that sends the spark to the electrode. The part you would need is a spark module PS11744058 Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Roi
August 22, 2017
Electricity not going to one of the igniters.Are both on same circut or seperate do i need new prong electrode and wire
For model number jenn air gas cooktop
Hi Roi, Thank you for your inquiry. If your stove will not start, element does not heat, or gas igniter glows but does not light, replacing the igniter can solve these issues. For this installation, you will need a Phillips screwdriver and needle nose pliers. First place the grate on top of the burner, then lift the burner and disconnect the wires. Next remove the two Phillips screws from the bottom of burner, pull igniter out of the burner and wiggle in the new one. Refer to the installation instructions provided by the manufacturer for more instructions. I hope this helps. Thank you and have a great day!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Derrik
November 22, 2019
Our jenn air gas range has two burners that won't light. Do we need to replace both ignitors? They quit working at the same time? Or could there be another problem?
For model number JDS9860ACB
Hello Derrik, thank you for inquiring. You will need to replace the Spark Igniter Set, part number PS11744110 for your model range. Good luck with your repair!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Debby
December 12, 2019
One burner will not auto light but the burner behind it will. When i turn the dial to ignite there is no clicking sound.
For model number JGD8345ADB
Hi Debby, thank you for your question. There are a couple of parts to check in this case. First you should check your burner electrode. Then you should take a look at your igniter switches/harness. If those parts are fine then you may have to look into your spark module being the issue. We hope that helps. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Patrick
February 7, 2020
No spark from burners on left side don't work but if I swap the burners from the right it works.
For model number JDS9860AAB
Hi Patrick. Try to clean out the igniters if this does not work than you will have to replace the igniter. Thank you for your question and good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Shengli
November 11, 2019
I was cleaning up my stove (jenn air/Maytag jds9860acp) and somehow two burners on same side did now start afterwards. I thought the igniters were somehow damaged because of wet. Bought two new ones and installed. Still did not work. The igniter module is fine for sure because other two burners work just fine. What is the mysterious thing and how I can fix this problem. Thanks!
For model number JDS9860ACP
Hello Shengli, Thank you for the question. I suggest testing the Igniter Switch PartSelect Number PS11744350. These sit behind the knobs on the valve. Check the switch to see if it has continuity in the light position. Hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Shengli
November 11, 2019
Thank you for your reply. The igniter switch must be good because the good burners work at both left and right sides. I believe the voltage is there at the ignitor and the gap looks good as well. But just no sparks. Can you please advise? Thank you!
For model number JDS9860ACP
Hi Shengli, I could only recommend to replace the burner igniters on the non-working burners. Thank you for your question and good luck with your repair!

Was this helpful?
Thank you for voting!
Alexander
February 1, 2020
Need igniter and the gasket also as mine is deteriorated
For model number 31213wav
Hello and thank you for writing. The top burner ignitor with electrode PS2082000 is in the list of compatible parts for your model. We hope this helps. Please contact us anytime if you require further assistance. The gasket is no longer available it has been discontinued.

Was this helpful?
Thank you for voting!
Hazem
February 5, 2020
I replaced the top burner igniter but still did not spark
For model number MGR5752BDQ
Hello and thank you for writing. It certainly sounds like it could be a faulty spark module PS2086288 you should check the part(s) for signs of damage or test with a multimeter, and replace the part(s) as needed. We hope this helps. Please contact us anytime if you require further assistance.

Was this helpful?
Thank you for voting!
Related Parts:
Sue
January 10, 2018
Neither of the burners on the right side will ignite. Neither of them have the necessary "clicking" sound when I turn the knob to the lighting position. They are getting gas. Both burners on the left side work fine. Thanks for your help.
For model number JDS9860AAP
Hi Sue, Thank you for the question. If the switch behind the knob is not making the click when the knob is turned they may need to be replaced. The switches are all attached to harness,PartSelect Number PS11744350. You can test the switches with a multi meter. The switch should have continuity when it is in the light position. Hope this helps!

Was this helpful?
Thank you for voting!
Related Parts:
Part Videos

Replacing your Maytag Range Top Burner Igniter

Replacing your Maytag Range Top Burner Igniter play video
Customer Repair Stories
 Average Repair Rating: 4.0 / 5.0, 16 reviews. What's this?
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
  • roy from East Providence, RI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
  • Parts Used:
    74004053
136 of 151 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Gas burner head on stove top rusted out producing blue flame where there shouldn't be
Removed stove top module and unscrewed the bottom panel. Burner head rotated out fairly easily. I ordered both the burner unit and the igniter just to be safe even though the old igniter still worked. I used the other module as a guide to reassemble the unit. The new burner head was little difficult to rotate back in and did not rotate quite as far as the original so the gas pipe was just a fraction out of alignment but there is some flex so it worked out OK when it was re-installed. Everything worked perfectly when I turned on the burner and there are no gas leaks and no blue flames where there shouldn't be!
  • Joellen from Castro Valley, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
  • Parts Used:
    WP3403M075-10, 74004053
65 of 68 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
porcelan on igniter broken (2)
remove 2 screws that hold element in place, remove element, replace with new element, and replace screws , replaced burner assy on other
  • paul from mc neal, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
  • Parts Used:
    74004053, WP3412D025-09
30 of 44 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not light; ignitor did not produce spark
Take a few screws off the back of the slide in burner module. Take off the back. Unscrew the ignitor screw, remove ignitor carefully, replace with the new ignitor, put the screw back in, put the back back on, try it out! Ours worked after a couple of tries - don't know if the ignitor had to "rev up" by several sparks or we just didn't have it properly installed at first. Anyway, very easy. Did it in my pajamas on a Saturday morning.
  • Candace L. from Woodinville, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
  • Parts Used:
    74004053
16 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners were leaking gas, igniters didn't work
I had to use a pipe wrench to remove the burners. They were pretty stubborn to remove from the insert. Once this was done, I installed the ingniters into the underside of the burner, then installed the venturi tubes. After that, installing the burners only took simple placement and a quarter turn to lock them in. I adjusted the burner with a screwdriver and wrench as per the manuals instructions and that is all it took. I did a repair that cost me approx $150.00 to all 4 burners instead of buying two complete new burner inserts for $600.00 and it took less than 1 hour to do. I would do it again anytime.
  • Mitch from San Jose, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable), Wrench set
13 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner igniter would not spark to light the burner.
I had to unscrew 4 screws on the burner unit and then 2 screws on each igniter. slip the olds out and the new ones in and then replace all the screws. And wa la they sparked and I was cooking again.
  • Margie from San Antonio, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
  • Parts Used:
    74004053
12 of 16 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner would not ignite
Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.
  • Scott from Sacramento, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
  • Parts Used:
    74004053
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lack of burner gas ignition
I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.
  • Andrew from Lufkin, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
  • Parts Used:
    74004053
5 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced igniter in right rear burner
Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!
  • Marty from Kennesaw, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
  • Parts Used:
    74004053
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Igniter insulation had cracked and spark was shorting out on the flame holder whatchmacallit.
The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.
  • Melvin from Santa Maria, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
  • Parts Used:
    74004053
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Average Rating:
★★★★★
★★★★★
7 Reviews
4.9
Filter By Rating:
  • 5 Stars
    6
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
    Sort by:
    Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
      Model Cross Reference
      This part works with the following models:
      PartSelect Number: PS2082000
      Manufacturer Part Number: 74004053
      Brand
      Model Number
      Description
      Magic Chef
      31003SAA
      Range - Freestanding, Gas
      Magic Chef
      31003SAW
      Range - Freestanding, Gas
      Magic Chef
      31203KAW
      Range - Freestanding, Gas
      Magic Chef
      31203PAA
      Range - Freestanding, Gas
      Magic Chef
      31203PAQ
      Range - Freestanding, Gas
      Magic Chef
      31203PAV
      Range - Freestanding, Gas
      Magic Chef
      31203SAA
      Range - Freestanding, Gas
      Magic Chef
      31203SAW
      Range - Freestanding, Gas
      Magic Chef
      31203WAA
      Range - Freestanding, Gas
      Magic Chef
      31203WAW
      Range - Freestanding, Gas
      Magic Chef
      31213SAA
      Range - Gas
      Magic Chef
      31213SAW
      Range - Gas
      Magic Chef
      31213WAA
      Range - Gas
      Magic Chef
      31213WAM
      Range - Gas
      Magic Chef
      31213WAV
      Range - Gas
      Magic Chef
      31213WAW
      Range - Gas
      Magic Chef
      31213XAA
      Range - Gas
      Magic Chef
      31213XAW
      Range - Gas
      Magic Chef
      61S04PAA
      Range - Gas
      Magic Chef
      61S04PAW
      Range - Gas
      Magic Chef
      61S14WAA
      Range - Gas
      Magic Chef
      61S14WAW
      Range - Gas
      Magic Chef
      61S14XAA
      Range - Gas
      Magic Chef
      61S14XAB
      Range - Gas
      Magic Chef
      61S14XAW
      Range - Gas
      Magic Chef
      8241RA
      Cooktop - Gas
      Magic Chef
      8241RB
      Cooktop - Gas
      Magic Chef
      8241RS
      Cooktop - Gas
      Magic Chef
      8241RT
      Cooktop - Gas
      Magic Chef
      8241RV
      Cooktop - Gas

      Get in touch, we're here to help!

      Open until 1am EST

      Contact Customer Service