Part Location Diagram of 12002213 Whirlpool Transmission Pulley and Bearing Kit
See part 35 in the diagram
Replacing your Maytag Washer Transmission Pulley and Bearing Kit
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Transmission Pulley and Bearing Kit

 Fits your 6530A REV C!
★★★★★
★★★★★
10 Reviews
$88.76
  In Stock
 Fits your 6530A REV C!
PartSelect Number PS2003651
Manufacturer Part Number 12002213
Manufactured by Whirlpool
Product Description

Transmission Pulley and Bearing Kit Specifications

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY available in this kit. A worn bearing causes slow or no spin.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Maytag Washer Transmission Pulley and Bearing Kit

Replacing your Maytag Washer Transmission Pulley and Bearing Kit
Troubleshooting
This part fixes the following symptoms:
Spins slowly | Will not agitate | Will not drain | Burning smell
This part works with the following products:
Washer.
This part works with the following products:
Maytag, Norge, Admiral, Magic Chef.
Part# 12002213 replaces these:
AP4009132, 1042142, 12002213, 12001797, 12002213, 12002213VP, 12500036, 21001218, 21001298, 21001733, 21001734, 22004258, 22004259, 35-2016, 35-2078, 35-2119, 35-2318, 35-2439, 35-2441, 35-2683 ... Show more , 35-3455, 35-3457, 35-3829, LA-2007 Show less
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
10 Reviews
4.4
Filter By Rating:
  • 5 Stars
    5
  • 4 Stars
    4
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.8 / 5.0, 25 reviews. What's this?
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Washer tub would not spin, pump would empty water from tub.
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Other Parts Used:
Drive Belt - 52 inches long
  • James from Hueytown, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
349 of 397 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump Making Horrible Noise And Brake Stuck
The pump was very easy to replace (3) screws, easy to reach with front panel off. (Less than 5 minut job. The brake assembly and thrust bearing was a little harder to do, but not bad at all. I found it best to flip the unit upside down to do the brake assembly. Replaced #10-24 x 1/2" screws with 2" long ones. Remember to do this (1) at a time, then back all (6) off a little at a time to release tesion on the 200lb spring. Swap out parts and tighten back down with 2" screws and then swap them back out for the 1/2" ones (1) at a time. I tipped the unit back on its side to install the bearing & pully kit. This takes some of the weight off of the main shaft allowing you to insert the spacers and split ring. The replacement parts seem to be of eqal or better quality to the originals. Machine runs quiet and smooth.
Other Parts Used:
Drain Pump with Pulley Brake Stator Washer Brake Rotor
  • MICHAEL from PLYMOUTH, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
116 of 135 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would agitate, pump, but not spin
First I unplugged it, then removed the agitator and tub assemblies, then I tipped it back and removed the belt and pully and thrust bearings. After reading on here I learned the brake would stick and after installing the thrust bearing kit I found out I couldnt fit in the shims. That led me to believe the brake was siezed inplace so i couldn't fit in the parts. I removed the thrust bearing kit and removed the transmission assembley. I took apart the brake and found the two pieces had siezed together, after I got them apart I sanded both peices and lubed the shaft with high temp silicone like you would use on a cars brake system. I put the brake back together, BE VERY CAREFUL THE SPRING HAS ALOT OF PRESSURE! I then put the transmission back in, reinstalled the thrust bearing kit and it fit great. I put in the tub and agitator and washed clothes.
Other Parts Used:
Snubber Ring
  • steve from lebanon, OH
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench set
61 of 73 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would agitate, drain, but would not spin
I put the washer on the spin cycle and could see that the tub wanted to move. While it was trying to spin I leaned the washer forward and saw that the motor was spinning and the belt was turning, but the tub wasn't. Did some reading and it was the thrust bearing. I ordered the part and replaced them (very easy, follow the directions that come with the set). After install, the tub would spin.
Other Parts Used:
  • michael from mountain home, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
42 of 47 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would not spin water out in heavy loads
You do not have to remove any water lines to do this repair. Just unplug the machine from the electric outlet and tip it up on its back to make the repair. I removed the old belt and parts per the instructions. The new kit does not look like the old one. Make sure you mark the minimum and maximum marks with a sharpie on the plastic pulley before intalling it. This will help line up the cam bearing to test the spin cycle. The repair kit says to use the thickest washer but mine would not fit on so I used the thinner washer. Keep the other washer so that in the future if the plastic part wears down and you have spinning problems again you can replace it with the thicker washer. Also make sure you buy a new belt and replace the belt. I loaded it up with a full load of jeans and it works great.
Other Parts Used:
  • marcus from mansfield, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
42 of 47 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Load was to wet after last spin cycle.
Turned off water suply. Removed drain (pipe is short). Then slid washer out so I could tilt it back and work under the washer. I put a wood brace under the front of the washer for safety. I then followed the instructions that came with the parts.
Other Parts Used:
Washer
  • Earl from Crest Hill, IL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
33 of 46 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes were too damp after spin cycle finished.
Unplugged and removed the drain and supply hoses from the back; some water will run out so be ready for that. I laid the machine down on two 2x4s to keep from crushing the supply and drain nipples. Just follow the instructions included with the parts, all steps are straight forward accept for two things: 1. they talk about pulling down on the transmission shaft to slip on the retaining clip. With only the end of the shaft sticking out there isn't much to grab on to. I found by using a thin blade scraper inserted into the retaining clip groove, prying downward on the shaft I could then get a regular screwdriver blade into the same groove and expose the entire groove and slip on the clip. 2. they talk about "Adjusting Brake Disengagement" after studying this for a while it just refers to which thickness of thrust washer to use. After trying both the .062 and .032 I found that only the .032 would allow the retaining clip to engage. Rechecking the brake disengagement, everthing seemed to work fine. The machine now has a stronger spin cycle and even bath towels are ready for drying after the normal spin.
Other Parts Used:
  • Brian from South Holland, IL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
31 of 35 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Squealing noise in spin cycle this did not fix it!
This was easy except for the e-ring which was extremely difficult to remove. When I put the new one on I filed down the bottom of the front edges to make it easier to slide it on. Beware: If you have the washer tipped back against the wall when you do get the e-ring off everything will come sliding off the shaft all at once and go everywhere. These parts are covered with black grease and made quite a mess so you might want to have someone hold them in place so you can gently slide them off one piece at a time.
Other Parts Used:
  • Ron from Oxford, MI
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
24 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't spin
I took out all the tubs and the apparatus holding the gear and thrust bearing assembly. I used a homemade tool (long zipties) to pull the springs off and to put them back on. After that I just replaced the thrust bearing with the new kit and put everything back together.
Other Parts Used:
  • Elmer from Fort Campbell, KY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers, Socket set, Wrench (Adjustable), Wrench set
20 of 23 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Machine growned when washing, brake was slipping
Tried to remove brake stator with machine tilted back. Thisforced the stator off center. Removed the 6 holddown springs, water level hose and drain hose. Pull drum & transmission out of the case. Placed the drun on the ground, brake facing up. Replaced the short screws on the brake stator with 2" screws one at a time. Caution the spring has 200 lbs of force. Used 2" screws to back off spring. With spring tenshion released replace parts. Reversed proceedurer. Machine quite. Wife is happy.
Other Parts Used:
Brake Stator Washer Brake Rotor Brake Spring
  • Daniel from Sugar Land, TX
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set, Wrench (Adjustable)
19 of 25 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

38 questions answered by our experts.
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sherrie
March 7, 2018
I ordered the agitator; however, my Maytag washer still makes a horrible noise when washing. No noise when spinning.
For model number MAV6451AWW
PartSelect logo
Hi Sherrie, Thank you for your question. You might want to check out your transmission pulley and your lower bearing. I hope that helps. Good luck with your repair.

13 people found this helpful.

Was this helpful?
Thank you for voting!
Karl
November 14, 2019
I have a top load Maytag washer and it gets real loud while washing. I replaced the drain pump, belt and motor pulley cause originally it was loud during spin not anymore. Just when it washes it is loud. I took the belt off then put it back on wash cycle and it wasn't making loud noise so that let me know it's the thrust bearing or main valve bearing? What's your thoughts?
For model number AAV7000AWW
PartSelect logo
Hello Karl, Thank you for the question. I suggest checking the Lower Bearing Assembly PartSelect Number PS2003141 and the Transmission Pulley and Bearing Kit PartSelect Number PS2003651 for wear or damage. Hope this helps!

5 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Steven
April 29, 2019
Washer is having trouble building spin speed. Does this unit use a coupling or belt drive system. I have not taken it apart yet. Just trying to get price range of repair or replace unit. It still worked other than that.
For model number MAV208DAWW
PartSelect logo
Hello Steven, Thank you for the question. This model uses a Belt Drive System. The Belt is PartSelect Number PS11738882. Hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Larry
December 9, 2017
I replaced the brake rotor, snubber ring and the drive pulley and lower cam assembly, however, when i install the lower cam thrush washer, the shaft does not move out far enough to clear the thin thrust washer, much less the retained clip, even after using my screwdriver to pull the shaft out as far as possible. To verify different dimensions between the new and old parts, reinserted the old pulley and cam parts, and the problem still exists. (new brake rotor was left in place) any ideas on the cause?
For model number MAV7257AWW
PartSelect logo
Hello Larry. Thank you for your inquiry. I would double check to make sure everything is lined up correctly. Sometimes also the brake will stick, so you may want to check that to make sure it is not seized. We have a helpful repair video and installation stories available for this part. Good luck with your repair.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Rob
December 24, 2017
I replaced the thrust bearing kit and the bowl still don't spin is the transmission bad
For model number MAV2755AWW
PartSelect logo
Hello Rob, Thank you for your inquiry. This is one of the two top parts that have been reported to cause this issue, I would also check your drive belt as well. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Scott
December 31, 2017
Washer model mav755eww Maytag shakes drastically during the spin cycle even with washer tub empty (no water or clothes). Per the recommended fixes, i changed the suspension springs, the snubber ring, and leveled the washer but still shakes during spin cycle. I see that the transmission pulley/bearing kit is a possible cause but also the transmission/seal could also be a cause for shaking. The washer spins out fine, so it is more likely to be a bad/worn transmission pulley/bearing or the transmission. If it's the transmission, that is a $429 part which wouldn't make it feasible to fix on a 14 year old washer (could buy a new washer). The transmission pulley/bearing kit is only $53. What's the likelihood of doing the transmission pulley/bearing kit repair for $53 fixing the shaking issue?
For model number MAV7557EWW
PartSelect logo
Hello Scott, Thank you for your inquiry. We do show this part as being a more likelihood fix than the transmission. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Patsy
January 25, 2024
All at once after water filled and agitation began noise began, loud noise and proceeded through entire cycle to off. Any clue what could cause this. I would shut control off and on till turning to final spin out and then shut control off.
For model number HAV2357AWW
PartSelect logo
Hello Patsy, thank you for your inquiry. We have concluded that the issue is with the drive pulley, part number PS2003651. You may need to check it to solve the problem. Glad to be of assistance!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Al
November 17, 2019
Washer agitates but no spin. Attempted repair with thrust bearing kit.
For model number MAV4757AWW Washer
PartSelect logo
Hello Al and thanks for writing. If the washer will agitate but not spin the timer may be at fault. ... If the washer will agitate but not drain or spin then the usual suspect would be a bad lid switch. If the washer will drain but not spin then try turning the timer off then on again and see if the spin starts. We hope this helps. Please contact us anytime Timer Part Number: PS11738841 is in the list of compatible items for your model. We hope this helps. Please contact us anytime.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Rusty
December 13, 2021
I have a Maytag Performa, model # PAV2300AWW. It drains just fine, but more often than not, it won't spin, OR it spins too slowly to remove the all of the water from the clothes. I CAN get it to spin if I "help" it to get going. When it does spin, it is SO loud that ear plugs are needed. Is this fixable? Any help you can give me is GREATLY appreciated! Thanks!
For model number PAV2300AWW
PartSelect logo
Hello Rusty, Thank you for the question. We suggest checking the Drive Belt and the Transmission Pulley and Bearing Kit for wear or damage. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
RON
January 30, 2023
Pump works but would not spin clothes dry. When it works, spinning noise is loud. What part is needed to solve the problems? Appreciate your help. Thank-you!
For model number MAV9504EWW
PartSelect logo
Hi Ron, thank you for contacting us. If the spin is noisy, the problem is probably related to the transmission pulley and bearing kit, part number PS2003651. It includes the pulley that rotates the spin basket and the thrust bearing that fits between the pulley and the transmission shaft. Please reach out to customer service if you need help placing an order. Glad to be of help!

1 person found this helpful.

Was this helpful?
Thank you for voting!
  • 1
  • 2
  • 3
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS2003651
Manufacturer Part Number: 12002213
Brand
Model Number
Description
Norge
6002A
Washer - WASHER
Norge
6430
Washer - WASHER
Norge
6432A
Washer - WASHER
Norge
6432A REV A
Washer - Norge Washing Machine Model 6432A REV A (6432AREVA) Parts
Norge
6432A REV B
Washer - Norge Washing Machine Model 6432A REV B (6432AREVB) Parts
Norge
6432A REV C
Washer - Norge Washing Machine Model 6432A REV C (6432AREVC) Parts
Norge
6432A REV D
Washer - Norge Washing Machine Model 6432A REV D (6432AREVD) Parts
Norge
6433A
Washer - WASHER
Norge
6440A
Washer - WASHER
Norge
6440A REV A
Washer - Norge Washing Machine Model 6440A REV A (6440AREVA) Parts
Norge
6440A REV B
Washer - Norge Washing Machine Model 6440A REV B (6440AREVB) Parts
Norge
6440A REV C
Washer - Norge Washing Machine Model 6440A REV C (6440AREVC) Parts
Norge
6440A REV D
Washer - Norge Washing Machine Model 6440A REV D (6440AREVD) Parts
Norge
6440A REV E
Washer - Norge Washing Machine Model 6440A REV E (6440AREVE) Parts
Norge
6440A REV F
Washer - Norge Washing Machine Model 6440A REV F (6440AREVF) Parts
Norge
6440A REV G
Washer - Norge Washing Machine Model 6440A REV G (6440AREVG) Parts
Norge
6440A REV H
Washer - Norge Washing Machine Model 6440A REV H (6440AREVH) Parts
Norge
6440A REV J
Washer - Norge Washing Machine Model 6440A REV J (6440AREVJ) Parts
Norge
6440A REV K
Washer - Norge Washing Machine Model 6440A REV K (6440AREVK) Parts
Norge
6443A
Washer - WASHER
Norge
6443A REV D
Washer - Norge Washing Machine Model 6443A REV D (6443AREVD) Parts
Norge
6443B
Washer - WASHER
Norge
6530A
Washer - WASHER
Norge
6530A REV A
Washer - Norge Washing Machine Model 6530A REV A (6530AREVA) Parts
Norge
6530A REV B
Washer - Norge Washing Machine Model 6530A REV B (6530AREVB) Parts
Norge
6530A REV C
Washer - Norge Washing Machine Model 6530A REV C (6530AREVC) Parts
Norge
6530A REV D
Washer - Norge Washing Machine Model 6530A REV D (6530AREVD) Parts
Norge
6530A REV E
Washer - Norge Washing Machine Model 6530A REV E (6530AREVE) Parts
Norge
6530A REV F
Washer - Norge Washing Machine Model 6530A REV F (6530AREVF) Parts
Norge
6530A REV G
Washer - Norge Washing Machine Model 6530A REV G (6530AREVG) Parts
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service