Short Oven Sensor Kit

Repair tech checked oven and said the control panel was bad and needed to be replaced. The new control panel would cost over $450.00! I found that the oven sensor was bad and replaced it for $30.00. The old oven sensor had failed following a self cleaning cycle. I found that the wires coming out of it were burnt.

Replacing the oven sensor was very easy. I removed the back panels 6 screws to gain access to the sensor's connection. I then removed the 2 screw that hold the sensor in place inside the oven and pulled the old sensor out through the oven. I reversed this process to place the new sensor in the oven.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the element and attached the wires. Making sure I pushed the wires back through the hole far enough so the wires wouldn't touch the back of the stove. I then replaced the sensor by removing the two screws and pulling the wire through the hole so I could disconnect them. I reconnected the new sensor and made sure I pushed the wires back through the hole far enough away from the back of the stove. Replaced the screws and was all set to start the stove. I started the stove and it took about 10 min. to reach the set temperture. The stove worked great.

First I removed two screws that hold the oven sensor in place. I then removed the screws that held the panel on the back of the oven. I simply unclipped the plastic adaptor and replaced the old sensor with the new one. I screwed the sensor back in and put the back panel on. turned the power back on to the oven and hit the bake button. Voila!! The oven turned on and now it works like new!!!

Remove racks and pull out stove from wall. Remove back cover from stove. Unscrew and unplug sensor. Rethread new sensor wire through hole and plug in new sensor and rescrew plate that holds in place.

We had complications because of how the stove was installed, which delayed the "fix" time considerably.

Also installed ignitor. It was determined that both were bad. Gas would come on but not light. When oven would light, it would not re-light periodically to keep the temperature up, causing gas smell. This added time to repair of an additional 1 hour, and required removal of bottom drawer.

My oven stopped working and the display read F3 error. I looked up the code and found that it was probably the thermostat sensor. I ordered the part from partselect.com and when it arrived I went to install it but I ran into a somewhat scary issue. I found that I had to pull my oven out of the wall in order to replace the sensor.

After a minor nervous breakdown, I decided to go for it and found that it was much easier than I had imagined. Changing the sensor involves taking out the two screws that hold the sensor in place (inside of the oven), pulling it out to the point you can reach the connector, plugging in the new sensor and screwing it back in place. However, if you have an oven like my model, you have to pull out the whole oven from the wall in order to reach the plug on the sensor. This sounds like a lot of trouble but for me it was very easy. The oven is held in place with screws around the front side. Most are easily accessed and you don't have to take out any critical/complicated pieces of the oven. My screw gun made short issue of the problem and I found that the oven was out of the wall within minutes. I could then easily unscrew a small back cover, change the sensor and then screw the oven back into the wall. Being very careful, the whole operation took about 20 minutes. I recommend that you get help from a friend just because the oven is bulky. It is not heavy, an average sized male can handle the weight but it’s easier with a friend. Also, be careful that the gas hose which feeds the oven is long enough (and not tangled) for you to move the oven out of its space. Obviously, be careful about gas leaks.

Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven. Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

I removed the door by opening partially and pulling upward. It was a little heavy and you should make sure you have somewhere to put it. I removed screws and reinstalled the handle into the new door trim that had broken. It gave a great opportunity to clean the oven.
I then unscrewed the temp sensor from inside the oven and removed the back panel of the range to unplug the wires. I plugged in the new wires and tightened the screws.
The light bulb was easy. I pulled off the cover and unscrewed the old and screwed in the new. It was a lot of screwing and unscrewing but 3 easy tasks all the same.

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!