This kit includes the bracket, actuator, switch, screws and wire harness.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Norge Washer Lid Switch Kit
Troubleshooting
This part fixes the following symptoms:
Will not drain
This part works with the following products:
Washer.
This part works with the following products:
Norge, Magic Chef, Admiral, Maytag.
Part# 12001187 replaces these:
AP4008752, 1456, 12001187, 21001137, 21001148, 33-4276, 33-6470, 33-6471, 33-7118, 33-7412, 33-7634, 33-7745, 33-8289, 33-8290, 33-8307, 33-8828, 33-8911, 33-9063, 33-9064, 35-0920
...
Show more
, 35-2795, 35-2805, 35-2814, 35-2819, 35-3076, 35-3382, 35-3612, 35-3613, LA-1057, LA-1058
Show less
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Stanley R - October 14, 2018
Verified Purchase
Lid Switch
Was great to be able to get a part in such short time. Glad not to have to purchase a new machine. Machine works like it is brand new.
★★★★★
★★★★★
John C - March 28, 2024
Verified Purchase
switch replacement
removed 6 small screws , replaced part , put screws back in , less than 10 min. , video on repair cleared up any issues
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 2 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Intermittent problem with lid switch, no high speed spin/pump out
Disconnect power, unsnap and raise machine top cover w/lid, remove old switch - two screws under lid, taking care to not drop loose actuator lever into machine. Remove control panel back and disconnect switch wire connector. Intall new switch, taking care to not drop loose actuator lever into machine, connect switch wires inside control panel. Replace panel cover and lower machine top cover w/lid and snap into place, reconnect power, verify operation...
Other Parts Used:
Linda from La Porte, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
47 of 62 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My 24 year old Maytag performance washer started occasionally not agitating. Eventually it did not agitate at all but would spin.
The lid switch is on the right side top of the washer under the lid. I took a putty knife and found the clips that hold the top of the washer and pushed them to release it. I then lifted it up to fully see the lid switch. I unplugged the washer from the wall socket and took out the 2 screws that holds the lid switch in. Then unplugged the lid switch from its electrical connection and put the new one in its place. Washer is working great so far.
Other Parts Used:
Loretta from LEBANON JCT, KY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Donald
April 16, 2018
Washer won't spin but will fill and agitate is this my problem lid switch
For model number W205KA
Hello Donald, thank you for your question. If the unit will function in every other function but agitate the most likely issue is the lid switch. I would recommend replacing this part to see if it fixes the issue. Per your model, the lid switch is Lid Switch Kit 12001187. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Oscar
December 17, 2018
Machine operates as soon as water gets to the level needed with the lid open.Could this be a defective lid switch?
For model number PAV2200AWW
Hello Oscar, thank you for your question. The unit shouldn't agitate or spin with the lid open. If it does the lid switch is defective and should be replaced. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lorenzo
November 2, 2021
Washer begins spinning, but water comes out slowly. Water then comes out forcefully after lifting, then immediately lowering lid. I though the problem was the lid switch, which I replaced from Partselect, but the problem persists. Any suggestions would be appreciated?
For model number HAV2460AWW
Hello Lorenzo, Thank you for the question. We suggest testing the Water Inlet Valve. Set your multitester to the R X 1 ohms setting to test for continuity. Place each of the multitester's leads on a terminal. Your multitester should display a reading between 200 and 500 ohms. Closely examine your water inlet valve. The exact ohm resistance rating you should test for may be marked on the valve. We hope this helps!
Hello. My Admiral washing machine will not spin. I believe it is the actuator. I see you sell a replacement part for just the actuator. There is also a whole replacement kit for sale. How do I know if I need to replace the whole unit or just the actuator? Thank you for your help!
For model number AAV7000AWW
Hello Sarah,Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is PartSelect Number: PS2002890.You can test the switch with a multi meter and check for continuity. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Frances
January 25, 2018
My washer machine stopped working when I pulled out the knob to begin the washing machine. I am not sure what is wrong? It seems like the lid is engaging but there is no power.
Hello Frances,
Thanks for your question. The exact parts needed may vary from model to model, but there are a few general parts we can recommend. The lid switch, start switch, timer, drive motor, and main control board should be tested with a multimeter for continuity. Replace them if they fail electrical continuity. Examine the door strike as well for any signs of damage and replace it if needed.
I hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesn't seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing help...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
