Little to no heat when baking | Element will not heat
This part works with the following products:
Range.
This part works with the following products:
Frigidaire, Kenmore, Electrolux.
Part# 316505500 replaces these:
AP4322535, 316505501, 7316505500, 7316505501
Customer Repair Stories
Average Repair Rating: 3.0 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Bake element not heating correctly
Started with trying to take the door off for easier access to heating element.
I ended up lifting the door off and the front glass shattered and I sliced my hand open.
Ended up buying a new oven/range.
Other Parts Used:
Austin from GROTON, CT
Difficulty Level:
Very Difficult
Total Repair Time:
Less than 15 mins
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
10 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Doug
August 27, 2022
Some times the oven doesn't heat up, or when it does work it doesn't get up to temp, even though it beeps that if reaches the proper temp.
For model number LGEF3043KFN
Hey Doug, thank you for your inquiry. We have researched your model and found that the problem is with your temperature sensor. We recommend you change the temperature sensor, part number PS1528542. If you require assistance to place an order, please contact customer service. We hope that helps!
Hello Bernie, thank you for your question. Yes, this is the correct bake element for your model. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
TIM
December 27, 2017
My range suddenly would not heat up past temps in the 170's & it takes a while to get there. I replaced the temp probe & it did not make a difference. Getting heat from somewhere, both elements are warm but you can touch them with bare hand. Could both elements be bad? Or is the oven control board going bad?
For model number FGEF3055MFE
Hi Tim,
Thank you for your question. If you have just replaced the oven sensor, then you will need to check the electronic control board, the wiring connections between the electronic control board and temperature sensor as well as the bake and broil elements. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
David
December 5, 2018
Oven/bake does not heat over 370 degrees. Has a acrid, chemical smell. Supply power tests 155v @ each leg & 305v across the legs? Bake element tests 17 ohms bus has no burned areas or melt holes.
For model number 790.94463701
Hello David, Thank you for the question. I suggest Testing the Oven Probe, Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
TERI
January 2, 2019
Oven will not turn off
For model number LGEF3045KFJ
Hello Teri, thank you for your question. If the oven will not turn off at all we would recommend replacing the oven control board Part Number: PS9494055. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Pam
February 21, 2020
My brolier turns on when i put on the bake/quick bake. I've tested the thermostat and it is fine. We had an f10 error after a day trying to figure out what was wrong. Can it be that i need a new bake element? What's your opinion?
For model number Cgef3032mbb
Hello, Thank you for your question. You will want to look into the control board. Typically that is what causes the error F10. We hope this helps, good luck with this repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Khemraj
December 7, 2021
Is there a baking element on this model
For model number 79094462702
Hello Khemraj, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS1991807 for the Hidden Bake Element. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Patricia
July 14, 2021
Oven takes an hour to reach 400 degrees
For model number 79097459802
Hello Patricia, Thank you for the question. This is normally an indication the Temperature Sensor is defective and will need to be replaced. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. We hope this helps!
My oven takes for ever to get to 300. Was at 237 after an hour of being on. Could it be he bake element?
For model number CGEF3039RFA
Hi Marsha, thank you for reaching out. We would suggest checking the oven temperature sensor first. If it is fine, the issue could be with the oven control board, part number PS9494055. It monitors the temperature and controls the oven heat. You may need to replace it to fix the issue. We hope this solves your problem!
Oven shows set 350, 15-20m later up to 500 & F10code with alarm come on. Temp Sensor part 316490000 replaced. Still over heats but no F10code or alarm. Another part to try?
For model number EW30EF65GSA
Hello Mary, thank you for a very interesting question. The F10 code means that your electronic control board has detected a runaway temperature. To fix the issue, you may need to replace the control board, part number PS2378968. We hope this solves your problem!
