Product Description
Charcoal Filter Specifications
This Charcoal Filter traps grease from your oven's exhaust to help prevent it from entering the vent, which could cause damage over time. If the exhaust fan on your microwave is not working, you may need to replace your charcoal filter. This charcoal filter is located within the intake grille of your microwave, which will need to be unscrewed and opened to gain access to the filter. The manufacturer recommends that you change your charcoal filter every six months. This filter measures 5 inches by 5.375 inches by 0.375 inches. Be sure to measure your current filter to assure correct replacement. This product is sold individually. We recommend the use of gloves during installation to protect your hands from messy grease during your repair. You should also unplug your appliance at the electrical outlet or switch it off at the breaker. Using a Phillips screwdriver, unthread the screws securing the grill. Open the door and slide the grill to the left and lift it up to remove it. This will allow access to the filter so it can be either replaced or cleaned. Remember to insert the tabs of the grill into the frame and slide it to the right when you are done. To finish, shut the oven door and secure the grill with the screws.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Exhaust fan not working | Noisy | No heat
This part works with the following products:
Microwave, Microwave Oven Combo, Washer.
This part works with the following products:
Whirlpool, Maytag, Amana, KitchenAid.
Part# 8206230A replaces these:
AP4299744, 1266639, 8206230A, 8206230, 8206230A, 8206230ARP
Customer Reviews
Filter By Rating:
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Susan H - May 12, 2024
Verified Purchase
Easy repair, perfect fit
The part was exactly what was needed for my over-stove microwave. I have been unable to find it anywhere else so it was a relief to find a reliable supplier. Perfect fit.
Jim S - February 5, 2024
Verified Purchase
Simple part and good instructions
A little effort to replace but clear instructions made it esy.
Rick B - November 23, 2022
Verified Purchase
Microwave filter
Part was exactly as required. Great service. Would certainly use again.
Linda P - November 17, 2022
Verified Purchase
Prefect fit.
The part was exactly as described, with accurate info regarding models it would accommodate. Extremely quick delivery.
Jojo N - April 9, 2021
Verified Purchase
Easy to install and installation instruction is perfect
Part came in fast and installation is easy as instructed.
Benoit L - March 14, 2021
Verified Purchase
Easy repair and part in good conditions
My appliance is back in good order
Catherine L - October 13, 2020
Verified Purchase
Part is as described and functions great
Great service - fast delivery. Second order placed at PartSelect and very satisfied.
Gaity B - June 20, 2020
Verified Purchase
Was very easy to order and get your delivery
We were very pleased with the service we received from Part Select.
Marlene F - May 26, 2020
Verified Purchase
Easy repair.
Arrived very quickly. Very pleased.
Brian F - April 24, 2020
Verified Purchase
Good. Service
Part was perfect.
- < Prev
- 1
- 2
- 3
- Next >
Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 19 reviews.
What's this?
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Mounting brackets are fragile and plastic support is easily broken
Replaced the intake grille. The grille should be removed prior to cleaning. The entire part is plastic and easily broken so that the two tabs for the mounting screws are shattered and will not hold the part in place. If one attempts to clean the grille using only a moderate amount of pressure with a cloth the fragile plastic will break. The part is poorly designed. When the vent is removed to replace the charcoal filter, one may discover that the grille has already been broken in a previous cleaning operation.
Other Parts Used:
-
Richard from San Antonio, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
622 of 848 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
top plastic grill discolored
-
RUSSELL from RICHMOND HTS, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
333 of 527 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replacing Charcoal Filters
Remove two screws from Vent Grille, one on either side, and remove one screw inside Vent Grille on right side. Pull Vent Grille off exposing the two Charcoal filters. Remove the two Charcoal filters by hand and replace with new ones. Reinstall the Vent Grille and tighten screws. That's it. I'm not handy (ask my wife) and if I can do it so can you.
Other Parts Used:
-
Bud from GOODYEAR, AZ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
20 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Change broken 40W light bulb on Over-the-range Microwave
The original bulb came apart while unscrewing it from the back of the microwave, leaving the metal screw thread contact still in the socket. Since this is an over-the-range micriwave there isn't enough room to manuever needle nose pliers into the socket to remove the screw thread contact. So this is how we were able to remove it.
Unplug power cord.
Take a standard wine bottle cork and whittle down one end until it fits in the socket. Then, using a bit of pressure push the cork into the socket snd begin unscrewing the screw thread contact until it comes out of the socket. Works like a charm!
Unplug power cord.
Take a standard wine bottle cork and whittle down one end until it fits in the socket. Then, using a bit of pressure push the cork into the socket snd begin unscrewing the screw thread contact until it comes out of the socket. Works like a charm!
Other Parts Used:
-
Rosanne from BRIDGEVILLE, DE
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
13 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dirty filters
Remove top grill assembly and replaced filters,parts were delivered on time and fit as expected, Job well done!
Other Parts Used:
-
Mark from SCHAUMBURG, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
13 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
KMHS120ESS REQUIRES two charcoal filters
BEWARE: KMHS120ESS takes two charcoal filters. This site doesn't tell you that! I only figured it out after ordering one, receiving it, and removing the vent cover to replace it. So then I had to order another one and pay for shipping a second time (which cost almost as much as the filter itself). C'mon PartSelect, why are these not sold in a pair?
Other Parts Used:
-
Robert from AURORA, CO
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Install grease filter
Followed instruction already on your website
Other Parts Used:
-
Ben from PENNSVILLE, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Charcoal Filter clogged
Remove top grill screws [2] remove grill replace filter put back together.
Other Parts Used:
-
james from SHERRARD, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Prompt message appeared to change filters.
-
Frank J. from NORTHAMPTON, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic grille vent became brittle over time and broke when changing charcoal filter.
Replacing the grill is so ridiculously simple (two small screws) that it is hardly worth writing "instructions" for it.
However, ordering the right part is a problem. My microwave has a stainless steel exterior but on your parts list there is no part clearly identified as such. Only black and white. Then there's one for which an "image is not available" so I figured perhaps that might be it. However I received the white part in the mail.
I then enquired if the part with a stainless steel exterior was available, or just its broken plastic base so that I could transfer the stainless steel wrap from the broken piece. The white plastic part that I received does not have certain slots to attach the stainless steel wrap.
However, you merely confirmed that the part I received was white so that was not very helpful. I installed the white part and it looks absolutely horrible on top of a stainless steel oven but it is what it is. But not too happy with your service and website to be quite honest.
However, ordering the right part is a problem. My microwave has a stainless steel exterior but on your parts list there is no part clearly identified as such. Only black and white. Then there's one for which an "image is not available" so I figured perhaps that might be it. However I received the white part in the mail.
I then enquired if the part with a stainless steel exterior was available, or just its broken plastic base so that I could transfer the stainless steel wrap from the broken piece. The white plastic part that I received does not have certain slots to attach the stainless steel wrap.
However, you merely confirmed that the part I received was white so that was not very helpful. I installed the white part and it looks absolutely horrible on top of a stainless steel oven but it is what it is. But not too happy with your service and website to be quite honest.
Other Parts Used:
-
Henricus from GAINESVILLE, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- 2
- Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
- < Prev
- 1
- 2
- 3
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terry
May 7, 2019
I took the filter out to replace, but forgot if the mesh side is to be up or down.
For model number YKHMS2040BS-1
Hi Terry,
Thank you for your question. The mesh side should face up. I hope this helps. Thank you and have a great day!
21 people found this helpful.
Was this helpful?
Thank you for voting!
Rey
January 21, 2018
My microwave turns on but will not heat. I switched power setting to 90% and it warmed up some water but it i had to run it for four minutes. I took out the filters and they look good. I removed the unit from above the range. I am going to run it to see if the exhaust flue opens. I wont have time today but i will get to it tomorrow. The unit is two years old. I would like to avoid buying a new one and extended coverage is almost as much as a new unit. Any help would be appreciated. Thank you. Rey.
For model number WMH53520CS2
Hi Rey
Thank you for your question. There are a couple of parts you could check. I would suggest checking your door micro switches, your fuse, and your diode. I hope that helps. You should be able to test all three of those parts with a multi meter to see if they are working correctly. Good luck with your repair.
13 people found this helpful.
Was this helpful?
Thank you for voting!
Richard
December 27, 2017
How do i get to this filter do i have to pull the whole microwave to get to the grill to remove it?
For model number WMH1163XVS0
Hi Richard,
Thank you for your question. Before you begin any repair please unplug the appliance from the electrical outlet. Use a Phillips head screw driver to unthread the screws securing the grill. With the screws removed, open the microwave oven door then the slide the grill to the left and lift it up to remove. This will allow you to access the filter so you can either replace it or clean it. When you are done, insert the tabs of the grill into the frame and slide it to the right. Shut the oven door and then secure the grill with the screws. Restore power to the microwave. I hope this helps. Thank you and have a great day!
9 people found this helpful.
Was this helpful?
Thank you for voting!
Frances
July 23, 2017
How many charcoal filters does it take and do you have a pic to show this, not the parts pic's but how to install. Mine only has one, but one person stated it has 2.
For model number WMH1164XWS1
Hi Frances,
That is a good question. If your microwave only has one charcoal filter then just order one. I hope this helps. Thank you and have a great day.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Jimmy
October 11, 2017
When cooking it stinks up the house. When i checked the charcoal filter it only has one but there are two blowers so the one one the right is unfiltered and there is no way to install another filter.
For model number Whirlpool wmv1160cw-2 vent
Hi Jimmy,
Thank you for your inquiry. That is correct there is only one filter listed with your microwave. To verify if you can install another filter you will need to contact Whirlpool. Their telephone number is 1-800-626-2005. I hope this helps. Thank you and have a great day!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Greg Hensley
August 26, 2019
It appears i have 2 charcoal filters in my microwave. Is this True and what are the part no's. Also how do i order these parts, direct from Whirlpool or through supplier?
For model number WMH76719CZ-2
Hello Greg, thank you for inquiring. Your model microwave has one Charcoal Filter, this part number PS1871363. It has two Grease Filters, part number PS8769987. They are sold individually. To place an order, please feel free to contact customer service by phone or you may do so online. Thank you!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Chuck
February 25, 2018
When we place something inside to reheat and push the start button it wont turn on. The message "open and close door" displays. After many attempts it would turn on but after a couple weeks it got worse, but now it only beeps and the display is filled with lights. The unit was unplugged to stop the beeping.
For model number MMV4205DH
Hello Chuck thank you for your question. I would recommend replacing the door switches for your unit. There are three of them that should be replaced at the same time. Door Switch - 3 Terminal PartSelect Number: PS10057151, Door Switch PartSelect Number: PS2361111 and Door Switch PartSelect Number: PS2361113. If even one of these switches is not functioning properly the unit is not recognizing that the door is shut to allow the unit to run. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Toni
December 17, 2019
I've never replaced the charcoal filters and my unit is 2 1/2 years old and now won't heat. What is the part number on the charcoal filters?
For model number AMV6502
Hello Toni, thank you for your question. The Charcoal filter for your unit is PartSelect Number PS1871363. This charcoal filter is located within the intake grille of your microwave, which will need to be unscrewed and opened to gain access to the filter. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
William
February 18, 2020
Grease is showing up on doors of cabinets above microwave. Does this mean that 1 or more filters some where have to be replaced or is there more to it than this? What parts do i need and how many of them? How do i install them and is there a picture showing if they are on top, bottom or sides of microwave?Thanks.
For model number WMH31017AW-2
Hello, Thank you for your question. This model has 2 separate filters. Charcoal Filter- PartSelect Number: PS1871363, and Grease Filter- PartSelect Number: PS3650910. They both are sold individually. We hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Teresa
October 26, 2021
When my microwave says to check the filter, which one is it referring to? The charcoal or the grease?
For model number GMH3204XVS1
Hello Teresa, Thank you for the question. In most cases it is the Grease filter, however both are normally replaced at the same time. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- 3
- Next >
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1871363
Manufacturer Part Number: 8206230A
Manufacturer Part Number: 8206230A
Brand
Model Number
Description