Part Location Diagram of WE14M124 GE Top Bearing
See part 313 in the diagram
Replacing your General Electric Dryer Top Bearing
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Open until 12am EST

customerservice@partselect.ca

Top Bearing

★★★★★
★★★★★
1 Review
$96.71
  Special Order
PartSelect Number PS1766010
Manufacturer Part Number WE14M124
Manufactured by GE
Product Description

Top Bearing Specifications

The drum slides are not included with this part. The top bearing helps your dryer operate as quietly as possible. This part will require two green drum slides and 2 white drum slides.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your General Electric Dryer Top Bearing

Replacing your General Electric Dryer Top Bearing
Troubleshooting
This part fixes the following symptoms:
Noisy | Marks left on clothes
This part works with the following products:
Dryer.
This part works with the following products:
General Electric.
Part# WE14M124 replaces these:
AP4297334, 1257069, WE14M124, WE14M106, WE14M120
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.5 / 5.0, 25 reviews. What's this?
  • 1
  • 2
  • 3
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
LOUD - screeching noise during drying cycle, in all modes of operation.
1. Removed top cap on lid by removing the 3 - phillips screws.
2. removed front digital display panel from PC board.
3. removed bolts with nut-driver on the top of the front panel, removed bottom screws with #2 square bit.
4. removed "snap-in" plastic top bearing ( paying attention to where wiring is routed within this frame.
5. cleaned all areas of plastic and felt debris, installed new bearing, felt, and glides.
6. Re-installed all wiring and panels.

*** make sure to order all of the glides, there should be a total of 4 for the top assembly.
Other Parts Used:
FELT TRAP DUCT Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • Bruce from Springfield, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
242 of 331 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
clothes having black marks and getting stuck on top of drum, tearing
Repair was easy, following the disassembly instructions from the video on your site. What I did not know is that it takes 2 pieces of plastic slides from each kind to replace (makes a total of 4). I was lucky in that one of the white ones was still okay and that I accidentally ordered a second one from the greenish kind, so I was set. This was also a great opportunity to clean out the dryer which must have been a bucket full of lint. So far no more complaints. Given that this problem seems to reappear once in a while I'll order a new set soon.
Other Parts Used:
FELT TRAP DUCT Drum Bearing Slide - White (Sold individually) Drum Bearing Slide - Green (Sold individually)
  • Markus from Austin, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
170 of 248 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer making noise
First i took the top cover off
2nd i took the front cover off disconnected the wires but make sure that you mark the wires first.
3rd I pull the drum forward removed the three scews holding the rear bearing .
4th I remove the four screws holding the bearing bracket from heating element.To remove the bracket you might have to remove the heating element i only remove three screws and was able to put my hand behind it and pull the bracket out.
To put back just go in the reverse order.
note: get some one to help you.
Other Parts Used:
Rear Drum Bearing Kit Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • carlos from modesto, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
45 of 51 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
noise in drum
i took the front load dryer apart found the parts that were bad ordered the parts which were a snap at partsselect at first i thought it would be tuff to put back together but the site has good pictures i put the dryer back together but had a tuff time with the belt after i watched a video it went right together i found that taking pictures with my cell phone while taking things apart helped a lot when putting it back together all in all im proud of myself i didnt think i could do it but i did and the dryer works great i will be using the site again i used it a few months ago for my washer it it worked great too!!
Other Parts Used:
BELT DRIVE Complete Duct Trap Assembly Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually) Rear Drum Bearing Kit
  • billy from kissimmee, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
29 of 50 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes were getting stuck in the top of the dryer and as a result they were basically getting chewed up (creating holes in clothes).
I googled the problem and found a forum where people were having the same problem. Luckily I found a post that told me the exact parts I needed. I then found a video on youtube, followed every step and completed the repairs in about 45 minutes. I'm a housewife and found this fairly easy. The dryer now works like a charm!
Other Parts Used:
Drum Bearing Slide - Green (Sold individually)
  • andrea l from tomball, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
27 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
squeeky noise and eating clothing
I basically watch the video on how to get to the top bearing assy. and to replace the guides and it went pretty easy. The only thing was the drum had to be moved back into the frame because it was sticking to far out. I now have a new dryer and its very quite and does not eat the clothing any more. I received the part fast and I will use parts select for my other appliances.
Other Parts Used:
  • jesse from fullerton, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
19 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud squeaking
remove top cover and lean front panel foreward.
remove old top bearing and snap new one in place.
Other Parts Used:
Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • Clay from Murfreesboro, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Load squeaking
I replaced the slides and the top bearing. Watched a video on here on how to replace the slides. Which helped me remove the door properly. Very easy. Was able to do by oneself. Parts came really fast. Only down for two days.
Other Parts Used:
Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • Robert from Jamestown, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
9 of 12 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
glides and top housing worn out
removed top of unit, control panel and front of dryer. Disassembled assembly and installed new housing and glides, reassembled and checked operation
Other Parts Used:
Door Plug - White Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • roger from rio rancho, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
7 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer drum loud sqeeking noise
Worn out top bearing plastic part and worn out felt. Removed top part of the front where the dial and buttons are, then the top, then the front where the parts I was replacing were. It was overall easy and didn't require a cdertified repair person. These were parts that were worn out. I am dissapointed in the GE product. It is only 3 1/2 yrs old and already worn out. Poor design and poor quality parts. I will look at other brands next time when replacing the front loading dryer and washer. Overall a faril;y easy repair that most mechnicaaly oreinted person can do. Also thaks to partselct for the diagrams which helped tremendously with meticulous parts.
Other Parts Used:
FELT TRAP DUCT Light Bulb Drum Bearing Slide - Green (Sold individually) Drum Bearing Slide - White (Sold individually)
  • James from Kennesaw, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
  • 3
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

3 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Garry
January 28, 2018
My dryer develops a loud thumping noise as it heats up. After 10 minutes it is thumping at its loudest im sure this is a heat related problem because it doesn't thump if i run it on fluff which uses no heat this problem started after i replaced the top front bearing because the slides were worn off and the drum had started wearing into the bearing itself. I even put a new motor in it. The original problem was the dryer stop tumbling during heat cycles after about ten minutes(about the same time the thumping is at its worst) but it wasnt thumping originally i created that problem somehow after i replaced the bearing. It will automatically start tumbling and drying again after it cools down after about 5 minutes. This process goes on and on until it finally has the clothes dry after about a hour or so. My question is. What could i have done replacing the bearing that would make it thump during heatup(by the way i replaced the long felt peice too that goes around the bottom piece of the bearing. And 2nd im guessing that one of the 3 thermostats is faulty and thats why its kicking off when hot(never kicks off during non-heat fluff cycles) my understanding is that the thermisters only control turning the heat elements on and off.(is that correct?) so thermisters wont turn dryer off they will just cause heating problems when failing. I need advice on what parts i need advice on what i did to create this thumping noise. Thank you very much.
For model number DCVH515EF0WW
PartSelect logo
Hello Garry, thank you for your question. In regards to the bearing; It sounds like the thumping might be a result of the bearing at the back of the drum. I would check the rear bearing part number WE25M40 to see if the part is bad. In regards to the temperature problem; I would check the safety thermostat part number WE4M160 which is located on the heating element. This thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element. If the unit isn't cycling properly this might be the cause. While you in there testing that thermostat you might want to test the other ones that are located on the heating element as well. I hope this helps!

8 people found this helpful.

Was this helpful?
Thank you for voting!
Bob
February 3, 2020
Clothes are getting caught between the drum and front panel. I replaced the felt gasket but the problem still exist. Any idea of what could be causing the problem?
For model number DCVH515EF0WW
PartSelect logo
Hello Bob, Thank you for the question. We suggest checking the Top Bearing and Bearing Slides for wear or damage. We hope this helps.

5 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Gisele
July 26, 2019
I have changed the back bearing and the slides but dryer still can handle a very light load or it shuts down. It is very noisy. How can i be sure that changing the front bearing will fix it?
For model number DBVH512EFOWW
PartSelect logo
Hello Gisele, thank you for inquiring. For what you describe you will want to consider either the Duct Felt Seal part number PS9861764 or the Drive Belt part number PS1766009 for your model. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
  • 1
;
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1766010
Manufacturer Part Number: WE14M124
Brand
Model Number
Description
General Electric
DBVH510EH0WW
Dryer - Electric
General Electric
DBVH510EH1WW
Dryer - Electric
General Electric
DBVH510EH2WW
Dryer
General Electric
DBVH510EH3WW
Dryer
General Electric
DBVH510GH0WW
Dryer - Gas
General Electric
DBVH510GH1WW
Dryer - Gas
General Electric
DBVH510GH2WW
Dryer
General Electric
DBVH510GH3WW
Dryer
General Electric
DBVH512EF0GG
Dryer - Electric
General Electric
DBVH512EF0WW
Dryer - Electric
General Electric
DBVH512EF1WW
Dryer - Electric
General Electric
DBVH512EF2WW
Dryer - Electric
General Electric
DBVH512EF3WW
Dryer
General Electric
DBVH512EFG
Dryer - GE Dryer Model DBVH512EFG Parts
General Electric
DBVH512EFW
Dryer - GE Dryer Model DBVH512EFW Parts
General Electric
DBVH512GF0GG
Dryer - Gas
General Electric
DBVH512GF0WW
Dryer - Gas
General Electric
DBVH512GF1GG
Dryer - Gas
General Electric
DBVH512GF1WW
Dryer - Gas
General Electric
DBVH512GF2WW
Dryer - Gas
General Electric
DBVH512GF3WW
Dryer - Gas
General Electric
DBVH512GF4WW
Dryer
General Electric
DBVH512GF5WW
Dryer
General Electric
DBVH512GFG
Dryer - GE Dryer Model DBVH512GFG Parts
General Electric
DBVH512GFW
Dryer - GE Dryer Model DBVH512GFW Parts
General Electric
DBVH520EJ0WW
Dryer
General Electric
DBVH520EJ1WW
Dryer
General Electric
DBVH520EJ2WW
Dryer
General Electric
DBVH520EJ3WW
Dryer
General Electric
DBVH520EJ4WW
Dryer
Customer Service Representative

Get in touch, we're here to help!

Open until 1am EST

Contact Customer Service