Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Eddie C - October 1, 2023
Verified Purchase
Easy repair
Easy repair. Hopefully no more issues.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 4 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Machine would stop at spin cycle
After disconnecting water lines and power, tip machine onto its back. The actuator is located under the drum. Remove the cover over the motor/ drive belt. Actuator is located by the transmission and held on by several screws. Unplug the wiring harness and remove three screws with Phillips screwdriver. Install new actuator..
Other Parts Used:
Steven from COHOES, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
5 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer was stuck on rinse cycle
Research showed it was the transmission and the actuator . Parts were super easy to install and it solved the issue 100%
PS - I put some light lithium grease on the transmission and it’s quieter than it was when new
When to PartSelect Web site, used their trouble shooting guide, Used their advice, which was to replace the actuator. bought and installed the actuator which took around 20 minutes or so. washer started working fine after replacing. Thanks to the website I save a lot of money. Thanks PartSelect
Other Parts Used:
Lee from FORT WORTH, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not Agitate
Tip the washer on its back remove the agitator install new one under 15 minutes
Other Parts Used:
Scott from HILBERT, WI
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
17 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ralph
February 10, 2022
I need actuator with "rev 011" stamped on it. Does this actuator have that revision on it
For model number wtw4800bq1
Hello Ralph, thank you for writing. We can confirm that this Actuator has "rev 011" stamped on it. Our part number is PartSelect Number PS16221077. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Sean
September 27, 2022
Washer agitated and drains, but won't spin at the end of the cycle.
For model number maytag washer mvwc565fwo
Hello Sean, thank you for your inquiry! Our research indicates that the issue is probably with the Drive Belt, part number PS11747978. If that is not the problem or if you have already fixed that, then the problem would be related to the Drive Hub Kit, part number PS6012095. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
actuator stim pops out hole pup backi works fine week or two
For model number mvwc565fw2
Hello Glenn, thank you for contacting us. If the issue is recurring, the most likely solution is to replace the shift actuator, part number PS11769864. Also, make sure it is mounted correctly. Please watch the attached video for proper installation instructions. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
Washer sticks on sensing mode, just keeps filling with water
For model number WTW5000DW1
Hello Ralph, Thank you for the question. When the Washer is stuck on Sensing Cycle and not proceed to the Wash cycle, it is most likely a defective Water Filter. We hope this helps!
My whirlpool washing machine stays in sensing mode and makes a buzzing noise sound. Is it the shift actuator that's messed up?
For model number WTW5000DW1
Hello Montona, Thank you for the question. Your washer senses the contents to determine the load size and balance to decide on the right amount of water to clean the load. If it is stuck in sensing mode, you can try to reset the appliance. To reset, unplug the washer and leave it for about 15 to 20 minutes before powering it on again. Lift and close the lid about six times within 12 seconds to reset the unit. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bill
November 11, 2023
THE MACHINE WAS STARTED. THE WATER TO THE MACHINE WAS CUT OFF. THE PUMPWAS RUNNING AND THE MACHINE CUT NOE BE CUT OFF. I UNPLUGGED THE MACHINE. THEN PLUGGED BACK IN AND THE PUMP WAS STARING TO RUN BUT STILL COULD NOT BE CUT OFF AT THE SWITCH AND NOW ALL THE INDICATER LIGHTS ARE OUT. WHEN PLUGGED IN THE PUMP RUNS, BUT NOTHING ELSE WORKS.
For model number MVWX655DW1
Hello Bill, thank you for reaching out to PartSelect. It sounds like your washer is in flood mode. If the unit is in flood mode, you just need to unplug the washer for 60 seconds, so the washer knows you are in front of it. Then plug the washer back in and give it 20 minutes to finish its flood mode sequence. The drain pump will continue to run until the sequence is finished. Nothing will be harmed, it is designed to do this. Once it is done, the drain pump will shut off and you can use the washer like normal. Just be sure the water is turned onto the washer, and you should be good to go. Now, if the unit does not reset, the control board inside your control board, part number PS12114298, needs to be replaced. Good luck with the repair!
My washer fills with water and agitates but wont switch to the rinse cycle. It says it doesn’t detect water, but it just got plenty of water to go through the wash cycle. And I recently changed the water inlet.
For model number MVW6230hc2
Hi Jared, thank you for contacting us. First, we recommend checking if the inlet valve is installed correctly. If this does not help, we recommend checking the wire harness, part number PS16730931. If the issue persists, then you may need to change the control board, part number PS16660484. We hope this sorts out your problem!
What is the OHM Rating for the Acutator PS16221077 on a Maytag MVWC565FW0
For model number MVWC565FW0
Hello Matt, thank you for contacting us. Based on our research, the ohm reading should be between 2000-3500 ohms. We hope this information helps!
Was this helpful?
Thank you for voting!
Steven
March 25, 2023
Crosley washer fill up but doesn’t agitate then drains and spins
For model number CAW9244DW1
Hi Steven, thank you for contacting us. We would recommend checking the drive pulley, part number PS10057144, and the drive belt, part number PS11747978. If the issue remains, the problem might be with the actuator, part number PS16221077, or the drive motor, part number PS11757089. We hope this helps!
My washer won't agitate, but it spins & drains without issue.
For model number atw4676bq1
Hello Rhonda, thank you for contacting us. A faulty shift actuator can cause the transmission to be stuck in spin mode, resulting in the washer not agitating. You may need to replace the shift actuator, part number PS16221077. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
