The temperature sensor, also known as an oven probe, detects the temperature within the oven cavity. This temperature sensor is 9 inches in length and is a genuine OEM part. If your oven is too hot, not heating evenly, or has little to no heat when baking, you may need to replace the temperature sensor. Please make sure to disconnect the power to your range before starting your repair.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Frigidaire Range Temperature Sensor
Troubleshooting
This part fixes the following symptoms:
Oven is too hot | Little to no heat when baking | Oven not heating evenly | Element will not heat
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Blair S - September 29, 2021
Verified Purchase
The temp sendor works just fine
Easy to replace thermostat has been working well.
★★★★★
★★★★★
Robert K - November 11, 2021
Verified Purchase
Easy to repair. - solved my slow warm up problem
The part came fast and worked as expected. The lower element in my oven was erratic during the oven warm up. Also, the oven was not holding its temperature. I tested the element continuity, which was ok, and the 240 volts on the circuit board, also OK. Fortunately replacing the temperature sensor solved the problem.
★★★★★
★★★★★
Donna-Mae T - December 11, 2023
Verified Purchase
Great service
The part came quickly and was very easy to replace
★★★★★
★★★★★
Ed P - April 22, 2021
Verified Purchase
Easy DIY repair
Our oven is working again.
★★★★★
★★★★★
Dan S - April 11, 2020
Verified Purchase
Perfect Part
Probe received within promised delivery. Easy to install and works perfectly.
★★★★★
★★★★★
Mario S - January 18, 2020
Verified Purchase
Perfect match
The part is the exact one I needed. It fits and works great!Thank you!
★★★★★
★★★★★
Jack M - January 3, 2025
Verified Purchase
Painless Process
Was happy to find the part from a Canadian source for my older Kenmore Stove. Painless purchase process, quick deliver and an easy part to DIY.... and I could pay with PayPal.
★★★★★
★★★★★
Joe P - June 23, 2021
Verified Purchase
Oven working better than ever
The part easy to install. Came well packaged.part came quicker than expected.
★★★★★
★★★★★
James H - April 1, 2021
Verified Purchase
No complaints
Part arrived a few days after purchase. OEM part and resolved the appliances problem.
★★★★★
★★★★★
Alexandrine L - July 6, 2021
Verified Purchase
Easy repair
Delivery was quick and it was super easy to change the part.
< Prev
1
2
3
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 25 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
oven did not heat up
Replaced the probe because that's what this site recommended.The oven still does not heat up.
Other Parts Used:
Tim from ASHAWAY, RI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set
73 of 125 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven temp not consistent with setting
took off back cover and unplugged old unit and installed new unit. oven probe was not the issue. probally control panel malfunction of readings. will continue using oven temperatue gauge inside to get settings for temperture as temp is important for baking.
Other Parts Used:
john from spring, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
72 of 157 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
trouble code F10 low oven temperature, oven not overheating,low resistance reading on ohm meter
Turned off electric,removed rear panel and replaced part.oven is now operating good as new.
Other Parts Used:
Michael J from STATEN ISLAND, NY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
19 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven would not heat up error code F10 showing on veiw screen
move the range out and unplug power supply, removing the back cover allows access to the probe, this can be done with screw driver or nut driver, loosen clamp that holds power cord in place and move backing out of the way, be careful sheet metal can be sharp, locate the probe unplug the connector and remove screw holding probe, pull old probe out install new probe, fasten down and plug in connector. attach backing and tighten clamp on power cord, plug in to power supply, turn on oven and give it several minutes for probe to work, it took only 20 minutes to replace the bad probe and the oven works like new hop this helps
Other Parts Used:
Jess from DEWEY, OK
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
17 of 20 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Range would start beeping and needed to be unplugged.
Remove 4 screws on back panel. Unclip wire connector and remove probe and install new probe.
Other Parts Used:
George from TURNERSVILLE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
15 of 18 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
OVEN WOULD NOT HEAT UP OVER 100 DEGREES
I "You Tubed" disassembly and commenced by disconnecting electric power. Removed door via You Tube instruction, removed back panels of unit, and replaced the oven temp probe. Easy Peasy. Then removed bottom of oven, next level above the burner and started to remove the igniter. One nut refused to be removed so I removed the burner and cut the nut and drilled it out. I reinstalled the new igniter with a metal screw from the rear panel and reinstalled the burner. Through the tiny hatchway I reconnected the new igniter and reassembled the oven to test. Just fine heated to 350 in 7 minutes. Awesome. Then, I called my brother, Pat, to give his imprimatur to the hillbilly nut switch. He said ok, I am done.
To any reading this, I would order the igniter and the burner at the same time. That tough nut cost my one extra hour.
When the part arrived, I open the box. Cut off my breaker to the range. Pulled back the stove and unscrewed the back. Located the probe, unscrewed the one screw that held it in. I then unclamped the white connectors, remove the old probe, replaced it with the new one reclamped the connectors. Screwed it back into the range. Replaced the back and screwed that back together. It was so easy I was very proud of my self. I cut the breaker back on and cooked a can of biscuits just to see if it really worked. And it did. My bread was not burned, it was cooked to perfection.
Oven temp runaway tempreture, oven light out, sensor was changed for temp drifting low
The light and sensor were straight forward and easy. The EOC was as well but there was one glitch. You have to also purchase the black panel overlay, you cannot use the old one. While the adhesive will still adhere, the keypad is different and REQUIRES the new cover. This would have been good to know when I ordered parts as I did not know until I got the three parts and had to reorder the overlay creating a weeks delay in it's repair.
oven temp was not heating up to desired temp and using an oven thermometer to confirm
moved the range out to access back removed 5 screws from back panel removed 1 screw from thermostat installed new one replaced screws, done in 20 minutes problem solved
Other Parts Used:
philip from CLIFTON, NJ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
F10 code going off
Went well, and working thank you ??
Other Parts Used:
edward from BRISTOL, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
38 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Delano
November 24, 2019
Oven temp won’t go over 250 degrees. It also takes about 30mns to reach that temp.
For model number LGEF3045KFK
Hello DeLano, thank you for your question. The most common part that causes that issue is the oven sensor prob PartSelect Number: PS1528542. You can test it with a multi meter. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
51 people found this helpful.
Was this helpful?
Thank you for voting!
Edward
November 28, 2019
Used the self cleaner on the oven, and now it won't come on to bake. Broiler seems to be working. I have seen posts about a thermal fuse. Any help would be great. Thank you. I would like to repair it myself if possible. Not a good day to happen.....thanksgiving day!
For model number FFEF3017LSG
Hello Edward, Thank you for the question. I suggest testing the Oven Probe Sensor, PartSelect Number: PS1528542. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
17 people found this helpful.
Was this helpful?
Thank you for voting!
Rona
December 24, 2019
My oven does not heat evenly. I had the oven probe (sku# 31690003) replaced but it did not fix the problem.
For model number wfe324lw0
Hi Rona, thank you for your question. There are a few parts that could cause this issue in your appliance. First I would say test your elements with a multi meter to see if they are working correctly or not. They should be reading between 0 - 50 ohms to be working correctly. The other part you should check would be your oven temperature sensor. That can also be tested with a multi meter and should be reading between 1000 - 1100 ohms. If those three parts are fine however, then the issue may be in your control board. I hope that helps. Good luck with your repair.
10 people found this helpful.
Was this helpful?
Thank you for voting!
Desiree
October 26, 2021
Hi. Stovetop burners, clock and all displays working fine, but the oven is not coming to full temp. Last night it took over two hours to get to 227 degrees F. Have not seen either element glow orange, but by touch they are definitely heating up some, just not a lot. Have not been able to view bottom element, as one screw is rusted or stripped, and I haven’t been able to get it out yet. Are the heating elements a binary type thing? Are they ever “partially working,” or is it a case of: if they are heating at all, the issue is probably something else? Is it possible that this issue could be caused by a bad temperature sensor? If so, can that be tested without removing? Just trying to figure out what to check next, or what the issue likely is. Thanks so much for any help! Desirée
For model number LGEF3045KFB
Hello Desiree, Thank you for the question. This is normally an indication the Sensor is defective. In order to test it, the sensor will need to be removed. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. We hope this helps!
8 people found this helpful.
Was this helpful?
Thank you for voting!
IKE
November 2, 2021
What is the temperature sensor part number and the location of it in the oven?
For model number FGF368GQF
Hello Ike, Thank you for your inquiry. We have researched the model number you have provided and show the part number as PS1528542. It is located on the right hand side of your oven. We have included a link to our repair video on installing the part. We hope this helps.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Frank
October 29, 2019
The oven does not start up, replaced element. Still does not start up. Would it be the temp probe ?
For model number 79094142312
Hello Frank, Thank you for the question. It is possible the probe is defective. You can test it with a multi meter. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If both elements are not coming on, it is more then likley a defective Electronic Control Board PartSelect Number PS8689401. Hope this helps!
How do i know if it is an igniter or a sensor? My oven doesn't get hot igniter is orange.
For model number ffgf3023lwd
Hello Pat, thank you for your inquiry! We recommend replacing the Oven Bake Igniter if your oven isn't getting hot. If the element shortens out, is no longer glowing, or is only glowing red or orange, replacing the igniter is the solution. I hope this information helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Read
November 7, 2019
My oven will not start after cleaning. The igniter comes on and after about 10 seconds it trips the GFCI. I suspect a thermal fuse, but I cannot find one in the parts list.
For model number LGGF3043KFV
Hi Read,
Thank you for your question. There is no fuse for this model. According to your owner's manual, where your oven is a self cleaning oven, it cleans itself with high temperatures, which eliminates soils in the oven or reduces them to ash that you may wipe away with a damp cloth. The heat from the oven during the self cleaning may have damaged a wire in the oven that may be causing the breaker to trip. You will need to check with a technician to verify what is causing this issue. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Martin
November 10, 2019
Surface burners and oven is not working but clock setting is working.
For model number FEF368GBA
Hello Martin, thank you for your question. The oven control board is what control the oven. If the oven isn't working at all (bake or broil) the electronic board should be replaced. The surface burners are controlled by the infinite switches. We would recommend testing the switches to determine if they are faulty. I hope this helps.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Amanda
November 23, 2019
Can a temp. Sensor be going bad and still read good on a meter. Oven seems to lose heat and quit working after preheat. Sometimes u can turn it off and on and it will start back working group right everything going else works fine no codes either
For model number Ffef3015pwb
Hi Amanda, the temperature sensor is part PS1528542. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesn't seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing help...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
