Part Location Diagram of WH43X10033 GE Agitator
See part 300 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Agitator

$181.57
  Special Order
PartSelect Number PS1482518
Manufacturer Part Number WH43X10033
Manufactured by GE
Product Description

Agitator Specifications

This part does not include the agitator cap. Must order separately.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Will not agitate
This part works with the following products:
Washer.
This part works with the following products:
General Electric, Hotpoint.
Part# WH43X10033 replaces these:
AP3995147, 1264703, WH43X0135, WH43X0141, WH43X135, WH43X141
Back to Top
Customer Repair Stories
 Average Repair Rating: 3.5 / 5.0, 10 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
agitator would not turn during wash cycle
First raise the lid on the washer then remove the agitator by placing hands under the agitator 180 degrees apart and pulling up. Pulling up one side and then the other until the agiator lifts up and off. Mine was stuck tight so I had to really work it back and forth to get it loose. Be careful while lifting on the agitator because when it comes loose it could hit you in the face since you are over it while lifting. Once you get the agitator off use a 7/16 socket and 3/8 rachet and remove the coupling. Place the new coupling on the shaft, making sure to line up the splines on the shaft and the coupling and install the 7/16 bolt and thighten it. Place the agitator on the coupling by lining up the splines and pushing down on the agitator until it seats. Time to repair was 30 minutes.
Other Parts Used:
Agitator Coupling Kit
  • James from Rineyville, KY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
135 of 154 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator will not spin
Agitator would not spin and it was going to cost me I've a hundred soars for someone to come and fix it. I looked on this sight and found out what I thought was the problem and ordered four parts to fix it. I was amazed because they came in two days later. I started withe coupling which was the cheapest part and instaled it and it fixed it to return the other parts I called the 800 number and they emailed me a return authorization and I sent it back so it cost me 15 dollars and five minutes to fix it.
Other Parts Used:
Agitator Coupling Screw - 1/4-20 MCH HXW 5/8 S V-Style Drive Belt
  • Jared from georgetown, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable)
52 of 70 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
stripped agitator, would not move during wash cycle
drilled off top plate of agitator to gain access ot bolt, removed bolt, removed agitator, replaced coupler and new bolt, snapped in place new agitator.
Other Parts Used:
Agitator Coupling Kit
  • John from Savannah, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
36 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator came off of spline and broke
The bolt that held the agitator assembly on had sheared off. Had to drill out the old bolt out of the spline. After that, it was very easy. Just bolt the agitator assembly onto the spline and it worked like a charm
Other Parts Used:
Agitator Coupling Kit Screw - 1/4-20 MCH HXW 5/8 S
  • Michael from Lebanon Junction, KY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers
22 of 28 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator stripped
removed the old one and replaced with new
Other Parts Used:
Agitator Coupling Kit
  • Ron from Benton, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
13 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old one had developed rough or little jagged edges on the side
Just used hands to pry open the old agitator from the washer. If one angle does not work try another and go in a clockwise direction. The new agitator had a new coupling at the bottom, so I needed something to push it out from the top, found a long metal rod and easily pushed it down and out. Verified that new coupling was exactly the same as the old one. The old one was good so I just pushed the new agitator down on the old coupling and it worked fine.
Other Parts Used:
  • Ganesh from Miami, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The wife told me that the wash just wasn’t coming out very clean.
The wife told me that the wash just wasn’t coming out very clean. So I went to check it out and found that the agitator was just moving freely. Upon closer inspection I found that the coupler had stripped.
I was unable to get the agitator free from the coupler so I had to drill out the inside top of the agitator in order to get at the bold that held the coupler in place. Once I got that out the rest was real simple.
Just bolt in the new coupler and snap in the new agitator into place. That can be harder that you think.
I used a block of wood laid across the top and just tapped it with a hammer to set the unit in place.
Make sure that when you take it apart to save the bolt and the old cap unless you ordered a new cap.
Other Parts Used:
  • Joseph from Poughkeepsie, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking shaft seal
This sounds like an easy fix to replace the shaft seal after watching the video, Oh how WRONG was I.....Firstly the video and parts list show just pull the agitator off..... NOOOOOO the bolt (Screw) is deep inside the agitator and that has to be removed to get the agitator off.....maybe in some models they have changed this poor design but not mine....As the screw is open to all the water and detergent guess what, it was so corroded you could get a sock to grip on it. Only solution was to cut the agitator in half at the bolt head level to get a vice grip on the rounded bolt head to undo it........It doesn't stop there, then you have to remove the fins in the remaining part agitator to get get the vice grips on. OK so far so good, now try and undo the big left hand thread nut....good luck, totally corroded, tried penetrating oil, heating it up you name it, nothing. I had a 1 11/16 socket but you need a deep socked as the shaft protrudes too far...solution drill the nut in three places to break it off the thread....OK so far we are winning....Now try to get the split spacer off the corroded shaft, no way was that going to happen it did eventually span in half so had to buy that too.....NOW WE STILL have to get the washer off the shaft...Run out of space to continue...
Other Parts Used:
Tub Seal Screw - 1/4-20 MCH HXW 5/8 S
  • Donald from SAINT JOSEPH, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Socket set, Wrench (Adjustable)
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Slow agitation from worn out plastic groves and broke coupling
This might quite possibly be the easiest repair I have ever done!

I followed provided instructions for installing the agitator. No tools needed for installation.

I used a wrench to take a bolt off from the old coupling as it broke away agitator. Basically taking the old one completely off was more complicated than installing the new. Installation was a couple/three minutes tops.

Clothes washing machine works like a new one now.
Other Parts Used:
  • Goldie from CHEVIOT, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench (Adjustable)
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Exchange Agitator And Switch Rotary
Take out 1 1/4" bolt, slide adgitator off and new one back on. This job about 5 min. The rotary switch I took 3 screws off back of top housing and twisted old rotary off and twisted new rotary on. Then exchanged the 4 wires one at a time. About 15 min. For both jobs.
Other Parts Used:
Temperature Switch - 3 Position
  • JOHNNY from EADS, TN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

6 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
TINA GARCIA
February 6, 2018
Fills up and drains dont aggitate
For model number WJSR1070A1WW
PartSelect logo
Hello Tina, thank you for your question. If the unit is filling, and will drain, but will not agitate the defective part might be the lid switch, part number WH12X1043. I would recommend replacing that part first as that is the most common part to fix the issue you're having. I hope this helps!

3 people found this helpful.

Was this helpful?
Thank you for voting!
Steve
December 12, 2018
My daughter was washing a large pillow and from what she tells me that the seem on the pillow must of got caught on the agitator and ripped the pillow open spilling the contents into the water and tub. She stated there is alot of pillow filling mixed into the water and settled to the bottom of the tank. When she turns the washer on in various cycles the agitator does not move and makes a humming sound. She removed the rear drain and drained some of the water into a bucket and the water level in the tub went down. I don't know if some of the cloth fiber got tangled up around the shaft under the agitator or if it is the pump. Any help is appreciated....thanks
For model number WCSR2090D5WW
PartSelect logo
Hello Steve, Thank you for the question. I suggest removing the agitator and tub assembly to clean out any filling that would have got between the tubs and the agitator. You may also need to remove the drain pump and hoses to clear out any clogs. Hope this helps, good luck with this repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Miguel
January 10, 2019
The washer work for a few min and them stop and show a error code with reads le according to the manual is a problem with the motor but when i turn it off and on again it works and the motor does a few spins back and force any idea what could be the problem?
PartSelect logo
Hello Miguel, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the unit. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Andrew
February 12, 2019
I need a agitator for the model
For model number S1070A5WW
PartSelect logo
Hello Andrew, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PS1482518. If you also need to replace the agitator cap, it is part number PS12073992. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Johnella
January 28, 2020
Can i use the old cap instead of buying a new one?
For model number GTWP1000M1WW
PartSelect logo
Hello and thank you for writing. You certainly should be able to do that, just make sure there is no damage to the cap PS12073992. We hope this helps. Please contact us anytime if you require further assistance.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jason
December 5, 2021
Agitator won’t go under load. Will move some if you push down on it
For model number WJSR1070A1ww
PartSelect logo
Hello Jason, thank you for your question. We recommend checking the Agitator Coupling Kit PartSelect Number PS1517844. We have an installation video for you to access. Good luck and have a great day.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
  • 1
;
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1482518
Manufacturer Part Number: WH43X10033
Brand
Model Number
Description
General Electric
52120TAWB
Washer
General Electric
56021A0WW
Washer
General Electric
56031A0WW
Washer
General Electric
56041A0WW
Washer
General Electric
56051A0WW
Washer
General Electric
56121T2WW
Washer
General Electric
56121T3WW
Washer
General Electric
56121T4WW
Washer
General Electric
56121T5WW
Washer
General Electric
56121T8WW
Washer
General Electric
56121TAWW
Washer
General Electric
56121TBWW
Washer
General Electric
56200T2WB
Washer
General Electric
56200T3WB
Washer
General Electric
56200T5WB
Washer
General Electric
56220T6WW
Washer
General Electric
56220T8WW
Washer
General Electric
56220TAWW
Washer
General Electric
56220TBWW
Washer
General Electric
56221B0WW
Washer
General Electric
56221B1WW
Washer
General Electric
56221B2WW
Washer
General Electric
56221B3WW
Washer
General Electric
56221T6WW
Washer
General Electric
56411D0WW
Washer
General Electric
56411D5WW
Washer
General Electric
57131T2WW
Washer
General Electric
57131T3WW
Washer
General Electric
57131T4WW
Washer
General Electric
57131T5WW
Washer
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service