Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Clutch drive wore out and was making a clunking noise during operation.
I removed the front cover and the top cover. Then I unplugged all the,wires and removed the hangers. Then removed tub and drum together out the front. After beating on the tub nut for 2 hours and drenching it in liquid wrench I realized that the,tub nut was not going to release. Yes I was turning it clockwise. I bring out my chisel and hammer. After removing the,center shaft I chisel the,tube inward till I could get to the nut. Then I chisel the,tub nut into 3 pieces. It then appeared why it wasn't coming loose,earlier the powders,had gotten below the nut and had it cemenred on. So those youtube videos,are helpful to an extent.
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Todd
January 8, 2019
Is there a bearing in the drive pulley that could be making loud noise in spin cycle. Already replaced shaft
For model number GTWN2800D1WW
Hi Todd, thank you for your question. There is no separate bearing unfortunately. The pulley directly connects to the drive shaft and tube assembly. It could be that the inner part of your drive pulley has worn down a bit and that is the cause of the noise. You might actually be able to see that if you visually inspect the part. I hope that helps. Good luck with your repair.
Hello Ryan, Thank you for your inquiry. The most common causes are a damaged or loose belt, or a damaged or loose drive pulley. We recommend checking the belt for any fraying, and check the pulley nut holding the pulley to the shaft and mode shifter assembly. We also recommend checking the threaded end of the shaft if the nut is not staying snug. Good luck with your repair.
How much slop should there be between the drive pulley and the shaft and drive tube assembly. When I turn the drive pulley by hand it takes a bit before it will engage and rotate the tub and make a noise when it engages.
For model number gtwn4250d2ws
Hello Brian, thank you for your question. We have a Video on how to replace the Shaft & Drive Tube Assembly PS3652839. The should be of some assistance. We hope this helps.
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace...
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qu...
Also known as the gearcase or transmission. This part helps move the agitator back and forth during the wash cycle. New shifter mounting holes are NOT threaded, use original self tapping screws to install new part. Tub ...
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS1482349
Manufacturer Part Number: WH07X10019
