Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Dale P - November 20, 2021
Verified Purchase
Easy repair
Part was as expected. Very fast delivery. Machine back in working order. No more leaking
★★★★★
★★★★★
Laura B - August 6, 2018
Verified Purchase
Great Part
It was exactly what I needed and simple to install!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.9 / 5.0, 3 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
replaced drain hose that was missing
slipped the new drain hose on and with locking plyers slipped the wire clap in place after three trys
Other Parts Used:
Delmar from EAST TROY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
11 of 17 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Suspension rods were worn; washer is 10+ years old
Replaced the suspension rods, suspension rod supports, main drive belt, tub centering springs, water supply hoes, and washer drain hose. Taped new front suspension rods to side of tub to ensure that they did not slide down when raising the washer off its back from the floor. Had a helper lift the tub, which made attaching the new suspension rods easy. The tub is extremely heavy so by a helper lifting it up it made attaching the new suspension rods much easier. IMPORTANT: According to the technician's manual, which was taped to the inside of the washer, it is absolutely necessary to recalibrate the washer after replacing any suspension parts. We did this by following the instructions in the tech manual. Failure to recalibrate a washer could result in poor performance. The procedure is different for each brand or model of washer, but again is absolutely essential after replacing suspension parts of any kind. For some unknown reason, our washer did not have the tub centering springs. Our model should have had the springs.Facing the washer, we attached one to the front left tub housing and one to right rear of the tub housing. Recommend that anyone watch the installation videos for the suspension rods, center springs, and main drive belt before attempting the repairs.
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Other Parts Used:
Brian from DREXEL HILL, PA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers
2 of 9 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
10 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Victor
November 17, 2019
Hello i wanted to know how long this part is i need it to be 4-5ft to reach my drain
For model number W10468340C
Hello Victor and thanks for writing.
It is about 4 feet long. We hope this helps. Please contact us anytime
3 people found this helpful.
Was this helpful?
Thank you for voting!
Lois
July 2, 2019
Need a replacement hose as it is leaking.
For model number Kenmore 38 dehumidifyer
Hi Lois,
Thank you for your question. Before we can assist you further we would need the model number from your dehumidifier. The model number may be found behind the water reserve, behind the control panel or on the side or the back of the unit. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Carol
September 3, 2021
What is the length? I am looking for 6ft or longer.
For model number MVWX655DW1
Hello Carol, Thank you for the question. This hose is 4 feet long. You can order a Hose Extension to add to the existing hose to extend it to 8 feet total. PartSelect Number PS334681. This part is used to extend washing machine drain hose approximately 4 feet. You may also require the connector PartSelect Number PS334663 to connect the extension to the existing drain hose. We hope this helps!
Do parts PS334681 and PS334663 fit with our washer? Is there a shorter extension part that works with our model? We only need a foot or so.
For model number WTW5105HW
Hello Toni, thank you for your question. Both of the hoses fit your model but there is not a shorter one. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
JIM
May 15, 2023
How long is the replacement drain hose?
For model number MVW7232HW Maytag top loading washer
Hi Jim, thank you for reaching out. The drain hose, part number PS12578897, is approximately 4 feet long. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sean
January 13, 2020
What are the inside dimensions?
For model number RTW4641BQO
Hello Sean and thank you for writing.
The ID is just short of 1 inch. We hope this helps. Please contact us anytime if you require further assistance.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Barry
December 18, 2019
I see water leak just below panel of inlet hose connection
For model number wtw5500xw2
Hi Barry, thank you for your question. If you are having a leak from your hose then you may want to check that the connections are secure and that there are no breaks or damage to your hose. Good luck with your repair.
Was this helpful?
Thank you for voting!
Jennifer
September 11, 2021
I am looking for the diameter of the drain hose connector. Is it 1"? Thank you, Jennifer
For model number MVWC465HW2
Hello Jennifer, Thank you for the question. The Inner Diameter is just under 1 inch. We hope this helps!
Was this helpful?
Thank you for voting!
Tess
May 26, 2022
How many inches is the drain hose?
For model number WTW5000DW0
Hello Tess, Thank you for the question. This hose is 4 feet long. You can order a Hose Extension to add to the existing hose to extend it to 8 feet total Number PS334681. This part is used to extend washing machine drain hose approximately 4 feet. You may also require the connector Number PS334663 to connect the extension to the existing drain hose. We hope this helps!
Hello Robert, thank you for the question. According to our research, the drain hose for your model is part number PS12578897. This hose is 4 feet long. You can order a hose extension, part number PS334681, to add to the existing hose to extend it to 8 feet. You may also require the connector, part number PS334663, to connect the extension to the existing drain hose. We hope this information is useful!
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This solid element restorer is for ranges and cooktops. Solid element restorer restores and protects solid elements from rusting and spotting. Follow the instructions on the label when using this product.
This low-odor gel, easily cleans away tough burnt-on deposits at room temperature. Apply the gel evenly on the cooled oven surface. Leave the gel to set overnight then wipe away with a clean cloth.
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Model Cross Reference
This part works with the following models:
PartSelect Number: PS12578897
Manufacturer Part Number: W11244231
