Whirlpool 8193951A - Impeller and Seal Kit. | PartSelect.ca
https://partselectca.azureedge.net/Schematics/Whirlpool/46WLNAIP.gif
See part 23 in the diagram
https://partselectca.azureedge.net/Schematics/Whirlpool/46WLNAIP.gif

Impeller and Seal Kit.

7 Reviews

Your Price

CAD$85.40

PartSelect Number PS12069388
Manufacturer Part Number 8193951A
Manufactured by Whirlpool

This is the replacement impeller kit for your dishwasher. This impeller kit comes with 4 pieces, including the impeller and seals which you will need for the repair. The impeller and seal kit is mounted on the dishwasher motor. If your dishwasher is not cleaning dishes properly, it may be an indication that your impeller has gone bad, and you are not getting proper water pressure. If the seals have gone bad, your dishwasher may start to leak. If you are having either of these problems, you may need to replace the impeller kit. Be sure to disconnect the water and power source from the dishwasher before you begin this repair. This is an OEM part sourced directly from the manufacturer.

This part works with the following brands: KitchenAid, Kenmore, Whirlpool, Maytag, Amana, Estate, Magic Chef, Jenn-Air, Inglis, Crosley, Roper.

This part works with the following products: Dishwasher.

This part fixes the following symptoms: Not cleaning dishes properly | Leaking | Noisy

Videos For installing this part.

Questions & Answers
Ask our experts a question on this part and we'll respond as soon as we can.
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Installation Instructions Provided by PartSelect customers like you.
Average Repair Rating: 2.4 / 5.0, 6 reviews
What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Chauncey from Menan, ID
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Parts Used:
W10827015, W10874836, 8193951A, W10083957V
Started with a grinding noise in the bottom of the dishwasher, and then the thing just stopped cleaning the dishes. It wasn't pumping any water,
I removed the plasic inner parts, used the torx drivers to remove the internal platic plate that covered the sump. Found the food chopper cover and removed it. It had gotten a piece of plastiic wrapped around it. As it spun it had ground the teeth off the end of the drive on the impellor and the food chopper. I replace both as a set and it works fine.
83 of 145 people found this instruction helpful.
Was this instruction helpful to you?
Kathryn from Gordon, NE
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Parts Used:
8193951A
Dishes would not clean
Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.
33 of 39 people found this instruction helpful.
Was this instruction helpful to you?
Jerome from Greensburg, IN
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Parts Used:
8193951A
The ceramic seal had failed, allowing water to destroy the front motor bearing.
Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.
19 of 26 people found this instruction helpful.
Was this instruction helpful to you?
Gerald from Simsbury, CT
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Pliers, Socket set, Wrench (Adjustable)
Parts Used:
8193951A
Dishwasher would not pump water
.The easiest way to complete the impeller and chopper motor replacement is to disconnect the power, water and drain line, remove the dishwasher from the cabinet, set the washer on its back.

From this point everything is visible, pump housing, motor, etc. and it's a matter of disassembly and reassembly. Make note or a drawing of where all the wires are connected so you reconnect them in the right spots.

Reinstall water lines and power and check for leaks before replacing shield or kick plate.
17 of 34 people found this instruction helpful.
Was this instruction helpful to you?
Ashley from EDMOND, OK
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
8193951A, W10083957V
Chopper assembly failure
If your chopper assembly has a catastrophic failure like mine did, chances are it took out the teeth on the circulation motor as well. This will lead to the teeth on the chopper being destroyed by the impeller as soon as you turn the dishwasher back on. First, follow the instructional video to remove the motor (found on this site on the circulation motor page) and chopper assembly (also found on this site on the chopper assembly page). The impeller is screwed onto the input shaft of the motor, and you must keep it from turning so that you can unscrew the impeller assembly. I removed the back cover of the motor (there are four screws holding it on) and held a flat pry bar on the rotating assembly inside the motor to keep it from turning, then unscrewed the impeller from the shaft. Mine came off very easy, but be careful not to let your pry bar slip or damage the motors internals. After that, install the washer and grommet from the impeller seal kit on to the impeller, and screw it back on while keeping the motor from turning with your pry bar. Lastly, reinstall the motor and chopper assembly per the aforementioned instructional videos. The whole thing took around an hour to do, and it is much cheaper than replacing the entire circulation motor.
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
stephen from REDMOND, WA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Parts Used:
8193951A
Surprise, I'm not a plumber - replacing impeller and seal kit 8193951A
When the top rack stopped cleaning, I tracked down the problem to the food shredder/chopping blade, and then to the impeller that drives the blade. The knob on the impeller had sheared/broken off. That meant removing the motor, and replacing the impeller. Four hours, a band-aid, and a trip to Home Depot later, here are my suggestions

1. Look for videos – this site is awesome, but they don’t have a video on this particular repair. I found 4 that got me close to knowing what I was doing.
2. Do all the “remove internal stuff” - you had to anyway to find the issue with the shredder/cutting blade
3. Take pictures as you move along, you’ll need them when you have to remember the placement of the water line, drainage hose, wired connections etc.
4. You need a 1/4 inch socket set. A 3/8 drive will NOT work (it won’t fit between the shroud and the base). Don’t start working on the repair, unless you have a 1/4 in socket with about a 6" extension
5. Someone at Kitchenaid should be shot for having the waterline connection facing the back of the unit. Use a short adjustable wrench
6. The order comes with a washer, but when you take the impeller off this model, you’ll see you don’t need it.
7. Placement is everything – there was zero clearance between the bottom of the unit and the floor. Placement of the water line, drain hose, and power line was critical – had to re-position the unit about 7 times to get it to “play nice”.
8. Hindsight – only needed to remove the wire harness for the motor (take pictures)
9. Hindsight – gloves are a great idea – sheet metal is unforgiving
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
7 Reviews
4.7
out of 5
Filter By Rating:
  • 5 Stars
    5
  • 4 Stars
    2
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".

Model Cross Reference

Brand
Model Number
Description
Kenmore
665110739120
Dishwasher
Kenmore
665110739130
Dishwasher
Kenmore
665110739140
Dishwasher
Kenmore
665110739190
Dishwasher
Kenmore
66513102K900
Dishwasher
Kenmore
66513102K901
Dishwasher
Kenmore
66513102K902
Dishwasher
Kenmore
66513103K900
Dishwasher
Kenmore
66513103K901
Dishwasher
Kenmore
66513103K902
Dishwasher
Kenmore
66513104K900
Dishwasher
Kenmore
66513104K901
Dishwasher
Kenmore
66513104K902
Dishwasher
Kenmore
66513109K900
Dishwasher
Kenmore
66513109K901
Dishwasher
Kenmore
66513109K902
Dishwasher
Kenmore
66513112K700
Dishwasher
Kenmore
66513112K701
Dishwasher
Kenmore
66513112K702
Dishwasher
Kenmore
66513113K700
Dishwasher
Kenmore
66513113K701
Dishwasher
Kenmore
66513113K702
Dishwasher
Kenmore
66513114K700
Dishwasher
Kenmore
66513114K701
Dishwasher
Kenmore
66513114K702
Dishwasher
Kenmore
66513119K700
Dishwasher
Kenmore
66513119K701
Dishwasher
Kenmore
66513119K702
Dishwasher
Kenmore
66513212K901
Dishwasher
Kenmore
66513212K902
Dishwasher