Part Location Diagram of 5304507354 Frigidaire Detergent Dispenser
See part 9 in the diagram
Replacing your Frigidaire Dishwasher Detergent Dispenser
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.ca

Detergent Dispenser

★★★★★
★★★★★
7 Reviews
$79.43
  In Stock

Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.

PartSelect Number PS11770680
Manufacturer Part Number 5304507354
Manufactured by Frigidaire
Product Description

Detergent Dispenser Specifications

This part releases the detergent and rinse aid into the dishwasher. NOTE: Color may vary but the part will function the same as the original.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Dishwasher Detergent Dispenser

Replacing your Frigidaire Dishwasher Detergent Dispenser
Troubleshooting
This part fixes the following symptoms:
Will not dispense detergent | Door latch failure | Leaking | Not cleaning dishes properly
This part works with the following products:
Dishwasher.
This part works with the following products:
Frigidaire, Electrolux, Kenmore.
Part# 5304507354 replaces these:
AP6038540, 154452704, 154542104, 154542107, 154574405, 154574406, 154860103, 5304454285, 5304475588, 5304484723, 7154574405, 7154574406
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
7 Reviews
5.0
Filter By Rating:
  • 5 Stars
    7
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 3.6 / 5.0, 7 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Dispenser door broken.
Disconnect from power
Unscrewed 4 phillips screws from top of outer door.
Unscrewed 2 screws each siide of door.
Lower outer door section drops away.
Note wiring sequence on dispenser, then disconnect wires.
Unscrew 6 screws on dispenser and lift dispenser out.

Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw.
Reconnect wires to dispenser correctly.
Slide lower outer door over tabs and secure with the 4 side screws.
Ensure lower door is up under control panel and secure with the 4 top screws.

Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..
Other Parts Used:
  • C from Covina, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
56 of 67 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken door on dispenser
The only difficultpart was to figure out how to remove the stainless cover from the door. Seems it slides upwards after screws are removed. After that it is self explainatory and goes back together in 5 minutes.
Other Parts Used:
  • Justin from Miami, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
14 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rinse aid dispenser leaking and empty after 4 wash cycles
Needed to replace detergent / rinse aid dispenser unit on the inside top of door.

1) Need to remove outer door cover / panel by removing just two (2) screws - bottom screws on lower side panel. Door panel will drop vertically 1" to remove it.

2) Mark and disconnect the four (4) wires connected to the dispenser unit. The connections were so tight, it required pliers and a screw driver to loosen them.

3) Dispenser unit has four (4) screws holding it in place. Unscrew them and remove unit through door interior - this requires a bit of angling to get it out.

4) Position new unit through interior. Screw in place.

5) Re-attach four (4) wires in same sequence as disconnected.

6) Re-attach outer door cover. This is the most difficult part and really requires two people. It consistents of two sets of guide channels that most be aligned for the door panel to be secured re-attached.. Once aligned, the door cover must be moved vertically about an 1" and the screws re-attached.
Other Parts Used:
  • Paul from Lorton, VA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
7 of 18 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent Dispenser didn't work..
After turning of the power to dishwasher, I opened the door took of the two bottom screws on both sides of door. Closed the door and front panel just slide off. Then I took a picture of the dispenser to make use I could figure out how to put the wiring back together. Removed the six screws holding it in place and popped the dispenser out. Easy .. popped new dispenser in and lightly put all six screws back in ,wired it back up after checking my photo. Closed the door ,slid front panel back on opened the door put the 4 screws back in that hold the front panel .Turned power back on and Boom!! All done.. Not bad for a girl...
Other Parts Used:
  • Lori from IRMO, SC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser door latch broke
removed the screws holding the door together, then removed the screws holding the dispenser to the interior door. replaced the wires and put the door back together
Other Parts Used:
  • Stephanie from Fort Wayne, IN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken lid of the detergent dispenser.
The video show a different model, the only difference is that the screws for the top part shouldn't be removed only the ones that hold the front. Replace the detergent dispenser once the cover is removed is easy. All works like brand new. Thanks.
Other Parts Used:
  • oscar from WOODBRIDGE, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Would not dispense dish washing tablets
Turned power supply off to dishwasher Opened door and removed screws holding font of door Unplugged soap dispenser and removed six screws. Popped out and installed new dispenser. Plugged wires into new dispenser and installed front of door. Easy
Other Parts Used:
  • David from VERSAILLES, KY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

15 questions answered by our experts.
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Judy
October 12, 2017
I want to know if i can purchase the cap for the rinse aid dispenser without getting the whole dispenser. The dispenser if fine. The cap melted on one side and should be replaced. Thank you.
For model number GLD2445RFS0
PartSelect logo
Hi Judy, Thank you for your question. Unfortunately with this part you would have to replace the whole dispenser. Good luck with your repair.

20 people found this helpful.

Was this helpful?
Thank you for voting!
Larry
August 4, 2017
I replaced the detergent dispenser, and the door still will not open to release detergent with the new dispenser in place. What else could be my problem? Appreciate any help.
For model number FDBB4365FC0
PartSelect logo
Hi Larry, Thank you for your inquiry. There a couple of reasons why your detergent dispenser may not be dispensing correctly. The rinse aid cap may be lose and just needs to be tightened or it may be warped if it was damaged from the heat of the water in the dishwasher. You will need to remove the cap to inspect it. Also, the spring and hinge pin on the dispenser door could be the problem. The dispenser door is spring loaded, and is held in the closed position by a catch. Check that the spring and pin are not bent or broken and replace if required. If the catch is not releasing the door, then you should inspect the timer, the bi-metal release or the wax motor. I hope this helps with your repair. Thank you and have a great day!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Dragi
September 20, 2017
Can I order just the gray knob. That knob somehow was broken and a small piece is missing. Thanks and regards
For model number PLD2855RFC1
PartSelect logo
Hi Dragi, Thank you for your question. Unfortunately nothing on your dispenser is sold separately. If you need to replace that part, you will have to replace the whole dispenser. Good luck with your repair.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Sandra
January 9, 2020
Need dispenser for this Samsung dish washer. Dont know model number. Can you tell me the model or part number and how much. The wire that controls the release think the piece that was atta6 to the release catch, fell off and not sure if i need to replace the whole thing. Please give me both prices.
For model number DW80M9960US/AA
PartSelect logo
Hello Sandra, thank you for your question. The dispenser for this unit is PartSelect Number PS9606363. Please enter the part number into the site for current price and availability. Good luck with your repair!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Tom
January 27, 2018
Hi, is the timer that releases the detergent dispensing reservoir door included if I buy this new unit? Or is that timer located elsewhere? My tab that holds the detergent door shut is broken off, but I want to make certain the release timer is working correctly too.
For model number FDB4050LHS1
PartSelect logo
Hello Tom, Thanks for your question. The wax motor is the timer that releases the detergent, and for this model it is only included with the detergent dispenser itself. I hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jamie
February 16, 2018
I am trying to find the p/n for a dispenser cap. I accidentally melted the cap and i am needing a replacement cap. Can you help me with this?
For model number FPHD2491KF0
PartSelect logo
Hi Jamie, Thank you for your question. You can only get that part with the whole dispenser assembly. I have linked that part down below for you. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Jeremy
April 16, 2018
Hello I have ordered the detergent dispenser for this model dishwasher. In order to install it, do I have the remove the inside cover to the door? Thank you. Jeremy
For model number FPHD2491KF0
PartSelect logo
Hi Jeremy, Thank you for the question. Yes, in order to replace the dispenser the inside panel will need to be removed. Hope this helps!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Joann
November 7, 2018
My rinse aid cover melted due to it not being properly in place. I just need to replace the small cap, not the whole Dispenser. Do you sell the cap only?
For model number FDB4315LFC0
PartSelect logo
Hello Joann, Thank you for your question. Unfortunately with the Rinse Aid Cap, you would have to replace the whole dispenser as it is not sold on its own. Good luck with your repair.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Flora Keniston
December 7, 2019
Just bought house with above Kenmore dishwasher, I do not know what type of detergent to use is it powdered or tablets has main wash and pre wash places to put "something" would appreciate help i have never had a dishwasher before and am 76, looking forward to using it when all of the family are home for a meal
For model number 970015323300A
PartSelect logo
Hi Flora, according to the manual, use automatic dishwashing detergent only. Other detergents can produce excessive suds that can overflow out of the dishwasher and reduce washing performance. I would reference the manual for further help. Thank you for your question and good luck with your repair!

Was this helpful?
Thank you for voting!
Lori
April 18, 2023
I need only the cap for the rinse aid dispenser but it’s not offered on your parts page. I don’t need the whole soap dispenser. Please advise.
For model number FPHD2491
PartSelect logo
Hi Lori, thank you for the question. According to our research, the part number for the dispenser cap on this unit will be PS421128. We hope this information helps!

Was this helpful?
Thank you for voting!
  • 1
  • 2
;
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11770680
Manufacturer Part Number: 5304507354
Brand
Model Number
Description
Kenmore
58714683110
Dishwasher - Kenmore Dishwasher Model 587.14683110 (58714683110, 587 14683110) Parts
Kenmore
58715202800
Dishwasher
Kenmore
58715202801
Dishwasher
Kenmore
58715202802
Dishwasher
Kenmore
58715202803A
Dishwasher
Kenmore
58715203800
Dishwasher
Kenmore
58715203801
Dishwasher
Kenmore
58715203802
Dishwasher
Kenmore
58715203803A
Dishwasher
Kenmore
58715313000A
Dishwasher
Kenmore
58715382100A
Dishwasher
Kenmore
58715382100B
Dishwasher - DISHWASHER
Kenmore
58715383100A
Dishwasher
Kenmore
58715383100B
Dishwasher - DISHWASHER
Kenmore
58715389100A
Dishwasher
Kenmore
58715389100B
Dishwasher - DISHWASHER
Kenmore
58715392100A
Dishwasher
Kenmore
58715393100A
Dishwasher
Kenmore
58715399100A
Dishwasher
Kenmore
58715412100A
Dishwasher
Kenmore
58715413100A
Dishwasher
Kenmore
58715423100A
Dishwasher
Frigidaire
BBBD2432KB0
Dishwasher
Frigidaire
BBBD2432KF0
Dishwasher
Frigidaire
BBBD2432KW0
Dishwasher
Frigidaire
BGBD2432KB0
Dishwasher
Frigidaire
BGBD2432KF0
Dishwasher
Frigidaire
BGBD2432KW0
Dishwasher
Frigidaire
BGHD2433KB0
Dishwasher
Frigidaire
BGHD2433KB1
Dishwasher
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service